[1/3] ARM: dts: Add support for OX820 and Pogoplug V3

Message ID	20161021151037.20112-2-narmstrong@baylibre.com (mailing list archive)
State	Changes Requested, archived
Delegated to:	Neil Armstrong
Headers	show Return-Path: <listmaster@tuxfamily.org> From: Neil Armstrong <narmstrong@baylibre.com> To: linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-oxnas@lists.tuxfamily.org, devicetree@vger.kernel.org CC: Neil Armstrong <narmstrong@baylibre.com> Subject: [linux-oxnas] [PATCH 1/3] ARM: dts: Add support for OX820 and Pogoplug V3 Date: Fri, 21 Oct 2016 17:10:35 +0200 Message-ID: <20161021151037.20112-2-narmstrong@baylibre.com> In-Reply-To: <20161021151037.20112-1-narmstrong@baylibre.com> References: <20161021151037.20112-1-narmstrong@baylibre.com> Precedence: list Reply-To: linux-oxnas@lists.tuxfamily.org

diff --git a/Documentation/devicetree/bindings/arm/oxnas.txt b/Documentation/devicetree/bindings/arm/oxnas.txt index b9e4971..ac64e60 100644 --- a/Documentation/devicetree/bindings/arm/oxnas.txt +++ b/Documentation/devicetree/bindings/arm/oxnas.txt @@ -5,5 +5,10 @@ Boards with the OX810SE SoC shall have the following properties: Required root node property: compatible: "oxsemi,ox810se" +Boards with the OX820 SoC shall have the following properties: + Required root node property: + compatible: "oxsemi,ox820" + Board compatible values: - "wd,mbwe" (OX810SE) + - "cloudengines,pogoplugv3" (OX820) diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index befcd26..3b0c74f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -604,7 +604,8 @@ dtb-$(CONFIG_ARCH_ORION5X) += \ dtb-$(CONFIG_ARCH_PRIMA2) += \ prima2-evb.dtb dtb-$(CONFIG_ARCH_OXNAS) += \ - wd-mbwe.dtb + wd-mbwe.dtb \ + cloudengines-pogoplug-series-3.dtb dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8060-dragonboard.dtb \ qcom-apq8064-arrow-sd-600eval.dtb \ diff --git a/arch/arm/boot/dts/cloudengines-pogoplug-series-3.dts b/arch/arm/boot/dts/cloudengines-pogoplug-series-3.dts new file mode 100644 index 0000000..bfde32e --- /dev/null +++ b/arch/arm/boot/dts/cloudengines-pogoplug-series-3.dts @@ -0,0 +1,94 @@ +/* + * cloudengines-pogoplug-series-3.dtsi - Device tree file for Cloud Engines PogoPlug Series 3 + * + * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com> + * + * Licensed under GPLv2 or later + */ + +/dts-v1/; +#include "ox820.dtsi" + +/ { + model = "Cloud Engines PogoPlug Series 3"; + + compatible = "cloudengines,pogoplugv3", "oxsemi,ox820"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory { + /* 128Mbytes DDR */ + reg = <0x60000000 0x8000000>; + }; + + aliases { + serial0 = &uart0; + gpio0 = &gpio0; + gpio1 = &gpio1; + }; + + leds { + compatible = "gpio-leds"; + + blue { + label = "pogoplug:blue"; + gpios = <&gpio0 2 0>; + default-state = "keep"; + }; + + orange { + label = "pogoplug:orange"; + gpios = <&gpio1 16 1>; + default-state = "keep"; + }; + + green { + label = "pogoplug:green"; + gpios = <&gpio1 17 1>; + default-state = "keep"; + }; + }; +}; + +&uart0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; +}; + +&nandc { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "hamming"; + + partition@0 { + label = "boot"; + reg = <0x00000000 0x00e00000>; + read-only; + }; + + partition@e00000 { + label = "ubi"; + reg = <0x00e00000 0x07200000>; + }; + }; +}; + +&etha { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_etha_mdio>; +}; diff --git a/arch/arm/boot/dts/ox820.dtsi b/arch/arm/boot/dts/ox820.dtsi new file mode 100644 index 0000000..4592075 --- /dev/null +++ b/arch/arm/boot/dts/ox820.dtsi @@ -0,0 +1,298 @@ +/* + * ox820.dtsi - Device tree file for Oxford Semiconductor OX820 SoC + * + * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com> + * + * Licensed under GPLv2 or later + */ + +/include/ "skeleton.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/oxsemi,ox820.h> +#include <dt-bindings/reset/oxsemi,ox820.h> + +/ { + compatible = "oxsemi,ox820"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "oxsemi,ox820-smp"; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,arm11mpcore"; + clocks = <&armclk>; + reg = <0>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,arm11mpcore"; + clocks = <&armclk>; + reg = <1>; + }; + }; + + memory { + /* Max 512MB @ 0x60000000 */ + reg = <0x60000000 0x20000000>; + }; + + clocks { + osc: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + gmacclk: gmacclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + sysclk: sysclk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + clock-div = <4>; + clock-mult = <1>; + clocks = <&osc>; + }; + + plla: plla { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <850000000>; + }; + + armclk: armclk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + clock-div = <2>; + clock-mult = <1>; + clocks = <&plla>; + }; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges; + interrupt-parent = <&gic>; + + nandc: nand-controller@41000000 { + compatible = "oxsemi,ox820-nand"; + reg = <0x41000000 0x100000>; + clocks = <&stdclk CLK_820_NAND>; + resets = <&reset RESET_NAND>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + etha: ethernet@40400000 { + compatible = "oxsemi,ox820-dwmac", "snps,dwmac"; + reg = <0x40400000 0x2000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "rgmii"; + + clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>; + clock-names = "gmac", "stmmaceth"; + resets = <&reset RESET_MAC>; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + status = "disabled"; + }; + + apb-bridge@44000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0 0x44000000 0x1000000>; + + pinctrl: pinctrl { + compatible = "oxsemi,ox820-pinctrl"; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + pinctrl_uart0: uart0 { + uart0 { + pins = "gpio30", "gpio31"; + function = "fct5"; + }; + }; + + pinctrl_uart0_modem: uart0_modem { + uart0_modem_a { + pins = "gpio24", "gpio24", "gpio26", "gpio27"; + function = "fct4"; + }; + uart0_modem_b { + pins = "gpio28", "gpio29"; + function = "fct5"; + }; + }; + + pinctrl_uart1: uart1 { + uart1 { + pins = "gpio7", "gpio8"; + function = "fct4"; + }; + }; + + pinctrl_uart1_modem: uart1_modem { + uart1_modem { + pins = "gpio5", "gpio6", "gpio40", "gpio41", "gpio42", "gpio43"; + function = "fct4"; + }; + }; + + pinctrl_etha_mdio: etha_mdio { + etha_mdio { + pins = "gpio3", "gpio4"; + function = "fct1"; + }; + }; + + pinctrl_nand: nand { + nand { + pins = "gpio12", "gpio13", "gpio14", "gpio15", + "gpio16", "gpio17", "gpio18", "gpio19", + "gpio20", "gpio21", "gpio22", "gpio23", + "gpio24"; + function = "fct1"; + }; + }; + }; + + gpio0: gpio@000000 { + compatible = "oxsemi,ox820-gpio"; + reg = <0x000000 0x100000>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <32>; + oxsemi,gpio-bank = <0>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + + gpio1: gpio@100000 { + compatible = "oxsemi,ox820-gpio"; + reg = <0x100000 0x100000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <18>; + oxsemi,gpio-bank = <1>; + gpio-ranges = <&pinctrl 0 32 18>; + }; + + uart0: serial@200000 { + compatible = "ns16550a"; + reg = <0x200000 0x100000>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <0>; + fifo-size = <16>; + reg-io-width = <1>; + current-speed = <115200>; + no-loopback-test; + status = "disabled"; + clocks = <&sysclk>; + resets = <&reset RESET_UART1>; + }; + + uart1: serial@300000 { + compatible = "ns16550a"; + reg = <0x200000 0x100000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <0>; + fifo-size = <16>; + reg-io-width = <1>; + current-speed = <115200>; + no-loopback-test; + status = "disabled"; + clocks = <&sysclk>; + resets = <&reset RESET_UART2>; + }; + + rps@400000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0 0x400000 0x100000>; + + intc: interrupt-controller@0 { + compatible = "oxsemi,ox820-rps-irq", "oxsemi,ox810se-rps-irq"; + interrupt-controller; + reg = <0 0x200>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <1>; + valid-mask = <0xFFFFFFFF>; + clear-mask = <0>; + }; + + timer0: timer@200 { + compatible = "oxsemi,ox820-rps-timer"; + reg = <0x200 0x40>; + clocks = <&sysclk>; + interrupt-parent = <&intc>; + interrupts = <4>; + }; + }; + + sys: sys-ctrl@e00000 { + compatible = "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd"; + reg = <0xe00000 0x200000>; + + reset: reset-controller { + compatible = "oxsemi,ox820-reset", "oxsemi,ox810se-reset"; + #reset-cells = <1>; + }; + + stdclk: stdclk { + compatible = "oxsemi,ox820-stdclk", "oxsemi,ox810se-stdclk"; + #clock-cells = <1>; + }; + }; + }; + + apb-bridge@47000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0 0x47000000 0x1000000>; + + scu: scu@0 { + compatible = "arm,arm11mp-scu"; + reg = <0x0 0x100>; + }; + + local-timer@600 { + compatible = "arm,arm11mp-twd-timer"; + reg = <0x600 0x20>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3)|IRQ_TYPE_LEVEL_HIGH)>; + clocks = <&armclk>; + }; + + gic: gic@1000 { + compatible = "arm,arm11mp-gic"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x1000 0x1000>, + <0x100 0x500>; + }; + }; + }; +};

[1/3] ARM: dts: Add support for OX820 and Pogoplug V3

Commit Message

Patch