new file mode 100644
@@ -0,0 +1,73 @@
+* Mobiveil AXI PCIe Root Port Bridge DT description
+
+Mobiveil's GPEX 4.0 is a PCIe Gen4 root port bridge IP. This configurable IP
+has up to 8 outbound and inbound windows for the address translation.
+
+Required properties:
+- #address-cells: Address representation for root ports, set to <3>
+- #size-cells: Size representation for root ports, set to <2>
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- compatible: Should contain "mbvl,gpex40-pcie"
+- reg: Should contain PCIe registers location and length
+ "config_axi_slave": PCIe controller registers
+ "csr_axi_slave" : Bridge config registers
+ "gpio_slave" : GPIO registers to control slot power
+ "apb_csr" : MSI registers
+
+- device_type: must be "pci"
+- apio-wins : number of requested apio outbound windows
+ default 2 outbound windows are configured -
+ 1. Config window
+ 2. Memory window
+- ppio-wins : number of requested ppio inbound windows
+ default 1 inbound memory window is configured.
+- bus-range: PCI bus numbers covered
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- interrupt-parent : phandle to the interrupt controller that
+ it is attached to, it should be set to gic to point to
+ ARM's Generic Interrupt Controller node in system DT.
+- interrupts: The interrupt line of the PCIe controller
+ last cell of this field is set to 4 to
+ denote it as IRQ_TYPE_LEVEL_HIGH type interrupt.
+- interrupt-map-mask,
+ interrupt-map: standard PCI properties to define the mapping of the
+ PCI interface to interrupt numbers.
+- ranges: ranges for the PCI memory regions (I/O space region is not
+ supported by hardware)
+ Please refer to the standard PCI bus binding document for a more
+ detailed explanation
+
+
+Example:
+++++++++
+ pcie0: pcie@a0000000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ compatible = "mbvl,gpex40-pcie";
+ reg = <0xa0000000 0x00001000>,
+ <0xb0000000 0x00010000>,
+ <0xff000000 0x00200000>,
+ <0xb0010000 0x00001000>;
+ reg-names = "config_axi_slave",
+ "csr_axi_slave",
+ "gpio_slave",
+ "apb_csr";
+ device_type = "pci";
+ apio-wins = <2>;
+ ppio-wins = <1>;
+ bus-range = <0x00000000 0x000000ff>;
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <1>;
+ interrupts = < 0 89 4 >;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pci_express 1>,
+ <0 0 0 2 &pci_express 2>,
+ <0 0 0 3 &pci_express 3>,
+ <0 0 0 4 &pci_express 4>;
+ ranges = < 0x83000000 0 0x00000000 0xa8000000 0 0x8000000>;
+
+ };
@@ -197,6 +197,7 @@ lwn Liebherr-Werk Nenzing GmbH
macnica Macnica Americas
marvell Marvell Technology Group Ltd.
maxim Maxim Integrated Products
+mbvl Mobiveil Inc.
mcube mCube
meas Measurement Specialties
mediatek MediaTek Inc.
@@ -9162,6 +9162,13 @@ Q: http://patchwork.linuxtv.org/project/linux-media/list/
S: Maintained
F: drivers/media/dvb-frontends/mn88473*
+PCI DRIVER FOR MOBIVEIL PCIE IP
+M: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
+L: linux-pci@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/pci/mobiveil-pcie.txt
+F: drivers/pci/host/pcie-mobiveil.c
+
MODULE SUPPORT
M: Jessica Yu <jeyu@kernel.org>
M: Rusty Russell <rusty@rustcorp.com.au>