| Message ID | 1539667641-26024-2-git-send-email-hayashi.kunihiko@socionext.com (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
| Series | add new UniPhier PCIe host driver | expand |
On Tue, Oct 16, 2018 at 02:27:20PM +0900, Kunihiko Hayashi wrote: > Add DT bindings for PCIe controller implemented in UniPhier SoCs when > configured in Root Complex (host) mode. This controller is based on > the DesignWare PCIe core. > > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > Reviewed-by: Rob Herring <robh@kernel.org> > --- > .../devicetree/bindings/pci/uniphier-pcie.txt | 81 ++++++++++++++++++++++ > 1 file changed, 81 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/uniphier-pcie.txt > > diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt > new file mode 100644 > index 0000000..46a2754 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt > @@ -0,0 +1,81 @@ > +Socionext UniPhier PCIe host controller bindings > + > +This describes the devicetree bindings for PCIe host controller implemented > +on Socionext UniPhier SoCs. > + > +UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core. > +It shares common functions with the PCIe DesignWare core driver and inherits > +common properties defined in > +Documentation/devicetree/bindings/pci/designware-pcie.txt. > + > +Required properties: > +- compatible: Should be "socionext,uniphier-pcie". > +- reg: Specifies offset and length of the register set for the device. > + According to the reg-names, appropriate register sets are required. > +- reg-names: Must include the following entries: > + "dbi" - controller configuration registers > + "link" - SoC-specific glue layer registers > + "config" - PCIe configuration space > +- clocks: A phandle to the clock gate for PCIe glue layer including > + the host controller. > +- resets: A phandle to the reset line for PCIe glue layer including > + the host controller. > +- interrupts: A list of interrupt specifiers. According to the > + interrupt-names, appropriate interrupts are required. > +- interrupt-names: Must include the following entries: > + "dma" - DMA interrupt > + "msi" - MSI interrupt > + > +Optional properties: > +- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate > + phys are required. > +- phy-names: Must be "pcie-phy". > + > +Required sub-node: > +- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI > + interrupts. > + > +Required properties for legacy-interrupt-controller: > +- interrupt-controller: identifies the node as an interrupt controller. > +- #interrupt-cells: specifies the number of cells needed to encode an > + interrupt source. The value must be 1. > +- interrupt-parent: Phandle to the parent interrupt controller. > +- interrupts: An interrupt specifier for legacy interrupt. > + > +Example: > + > + pcie: pcie@66000000 { > + compatible = "socionext,uniphier-pcie", "snps,dw-pcie"; > + status = "disabled"; > + reg-names = "dbi", "link", "config"; > + reg = <0x66000000 0x1000>, <0x66010000 0x10000>, > + <0x2fff0000 0x10000>; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&sys_clk 24>; > + resets = <&sys_rst 24>; > + num-lanes = <1>; > + num-viewport = <1>; > + bus-range = <0x0 0xff>; > + device_type = "pci"; > + ranges = > + /* downstream I/O */ > + <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000 > + /* non-prefetchable memory */ > + 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>; > + #interrupt-cells = <1>; > + interrupt-names = "dma", "msi"; > + interrupts = <0 224 4>, <0 225 4>; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie_intc 1>, /* INTA */ > + <0 0 0 2 &pcie_intc 2>, /* INTB */ > + <0 0 0 3 &pcie_intc 3>, /* INTC */ > + <0 0 0 4 &pcie_intc 4>; /* INTD */ This is not correct and we must fix this concept for all DWC based host bridges bindings. We are mapping INTX to inputs [0,1,2,3] of the host bridge interrupt controllers and the binding should reflect that. This should be the correct mapping: interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ <0 0 0 2 &pcie_intc 1>, /* INTB */ <0 0 0 3 &pcie_intc 2>, /* INTC */ <0 0 0 4 &pcie_intc 3>; /* INTD */ Lorenzo > + > + pcie_intc: legacy-interrupt-controller { > + interrupt-controller; > + #interrupt-cells = <1>; > + interrupt-parent = <&gic>; > + interrupts = <0 226 4>; > + }; > + }; > -- > 2.7.4 >
Hi Lorenzo, On Mon, 19 Nov 2018 11:40:36 +0000 <lorenzo.pieralisi@arm.com> wrote: > On Tue, Oct 16, 2018 at 02:27:20PM +0900, Kunihiko Hayashi wrote: > > Add DT bindings for PCIe controller implemented in UniPhier SoCs when > > configured in Root Complex (host) mode. This controller is based on > > the DesignWare PCIe core. > > > > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > > Reviewed-by: Rob Herring <robh@kernel.org> > > --- > > .../devicetree/bindings/pci/uniphier-pcie.txt | 81 ++++++++++++++++++++++ > > 1 file changed, 81 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/pci/uniphier-pcie.txt > > > > diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt > > new file mode 100644 > > index 0000000..46a2754 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt > > @@ -0,0 +1,81 @@ > > +Socionext UniPhier PCIe host controller bindings > > + > > +This describes the devicetree bindings for PCIe host controller implemented > > +on Socionext UniPhier SoCs. > > + > > +UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core. > > +It shares common functions with the PCIe DesignWare core driver and inherits > > +common properties defined in > > +Documentation/devicetree/bindings/pci/designware-pcie.txt. > > + > > +Required properties: > > +- compatible: Should be "socionext,uniphier-pcie". > > +- reg: Specifies offset and length of the register set for the device. > > + According to the reg-names, appropriate register sets are required. > > +- reg-names: Must include the following entries: > > + "dbi" - controller configuration registers > > + "link" - SoC-specific glue layer registers > > + "config" - PCIe configuration space > > +- clocks: A phandle to the clock gate for PCIe glue layer including > > + the host controller. > > +- resets: A phandle to the reset line for PCIe glue layer including > > + the host controller. > > +- interrupts: A list of interrupt specifiers. According to the > > + interrupt-names, appropriate interrupts are required. > > +- interrupt-names: Must include the following entries: > > + "dma" - DMA interrupt > > + "msi" - MSI interrupt > > + > > +Optional properties: > > +- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate > > + phys are required. > > +- phy-names: Must be "pcie-phy". > > + > > +Required sub-node: > > +- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI > > + interrupts. > > + > > +Required properties for legacy-interrupt-controller: > > +- interrupt-controller: identifies the node as an interrupt controller. > > +- #interrupt-cells: specifies the number of cells needed to encode an > > + interrupt source. The value must be 1. > > +- interrupt-parent: Phandle to the parent interrupt controller. > > +- interrupts: An interrupt specifier for legacy interrupt. > > + > > +Example: > > + > > + pcie: pcie@66000000 { > > + compatible = "socionext,uniphier-pcie", "snps,dw-pcie"; > > + status = "disabled"; > > + reg-names = "dbi", "link", "config"; > > + reg = <0x66000000 0x1000>, <0x66010000 0x10000>, > > + <0x2fff0000 0x10000>; > > + #address-cells = <3>; > > + #size-cells = <2>; > > + clocks = <&sys_clk 24>; > > + resets = <&sys_rst 24>; > > + num-lanes = <1>; > > + num-viewport = <1>; > > + bus-range = <0x0 0xff>; > > + device_type = "pci"; > > + ranges = > > + /* downstream I/O */ > > + <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000 > > + /* non-prefetchable memory */ > > + 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>; > > + #interrupt-cells = <1>; > > + interrupt-names = "dma", "msi"; > > + interrupts = <0 224 4>, <0 225 4>; > > + interrupt-map-mask = <0 0 0 7>; > > + interrupt-map = <0 0 0 1 &pcie_intc 1>, /* INTA */ > > + <0 0 0 2 &pcie_intc 2>, /* INTB */ > > + <0 0 0 3 &pcie_intc 3>, /* INTC */ > > + <0 0 0 4 &pcie_intc 4>; /* INTD */ > > This is not correct and we must fix this concept for all DWC based host > bridges bindings. We are mapping INTX to inputs [0,1,2,3] of the host > bridge interrupt controllers and the binding should reflect that. > > This should be the correct mapping: > > interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ > <0 0 0 2 &pcie_intc 1>, /* INTB */ > <0 0 0 3 &pcie_intc 2>, /* INTC */ > <0 0 0 4 &pcie_intc 3>; /* INTD */ I see. Although this numbering has been affected by pci_irqd_intx_xlate(), I understand it's wrong for DWC based host. I'll fix the numbering next. Thank you, --- Best Regards, Kunihiko Hayashi
diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt new file mode 100644 index 0000000..46a2754 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt @@ -0,0 +1,81 @@ +Socionext UniPhier PCIe host controller bindings + +This describes the devicetree bindings for PCIe host controller implemented +on Socionext UniPhier SoCs. + +UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Required properties: +- compatible: Should be "socionext,uniphier-pcie". +- reg: Specifies offset and length of the register set for the device. + According to the reg-names, appropriate register sets are required. +- reg-names: Must include the following entries: + "dbi" - controller configuration registers + "link" - SoC-specific glue layer registers + "config" - PCIe configuration space +- clocks: A phandle to the clock gate for PCIe glue layer including + the host controller. +- resets: A phandle to the reset line for PCIe glue layer including + the host controller. +- interrupts: A list of interrupt specifiers. According to the + interrupt-names, appropriate interrupts are required. +- interrupt-names: Must include the following entries: + "dma" - DMA interrupt + "msi" - MSI interrupt + +Optional properties: +- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate + phys are required. +- phy-names: Must be "pcie-phy". + +Required sub-node: +- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI + interrupts. + +Required properties for legacy-interrupt-controller: +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupt-parent: Phandle to the parent interrupt controller. +- interrupts: An interrupt specifier for legacy interrupt. + +Example: + + pcie: pcie@66000000 { + compatible = "socionext,uniphier-pcie", "snps,dw-pcie"; + status = "disabled"; + reg-names = "dbi", "link", "config"; + reg = <0x66000000 0x1000>, <0x66010000 0x10000>, + <0x2fff0000 0x10000>; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&sys_clk 24>; + resets = <&sys_rst 24>; + num-lanes = <1>; + num-viewport = <1>; + bus-range = <0x0 0xff>; + device_type = "pci"; + ranges = + /* downstream I/O */ + <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000 + /* non-prefetchable memory */ + 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>; + #interrupt-cells = <1>; + interrupt-names = "dma", "msi"; + interrupts = <0 224 4>, <0 225 4>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, /* INTA */ + <0 0 0 2 &pcie_intc 2>, /* INTB */ + <0 0 0 3 &pcie_intc 3>, /* INTC */ + <0 0 0 4 &pcie_intc 4>; /* INTD */ + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <0 226 4>; + }; + };