| Message ID | 1542206821-24503-1-git-send-email-bharat.kumar.gogada@xilinx.com (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
| Series | PCI: Enable SERR# forwarding for Type-1 PCI devices | expand |
Hi All, Please let me know if anyone has any issue with this patch. Regards, Bharat > As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages will be forwarded > from the secondary interface to the primary interface, if the SERR# Enable > bit in the Bridge Control register is set. > Currently PCI_BRIDGE_CTL_SERR is being enabled only in ACPI flow. > This patch enables PCI_BRIDGE_CTL_SERR for Type-1 PCI device. > > Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> > --- > drivers/pci/probe.c | 20 ++++++++++++++++++-- > 1 file changed, 18 insertions(+), 2 deletions(-) > > diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index > b1c05b5..ed71e8e 100644 > --- a/drivers/pci/probe.c > +++ b/drivers/pci/probe.c > @@ -1841,8 +1841,6 @@ static void program_hpp_type0(struct pci_dev > *dev, struct hpp_type0 *hpp) > pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER, > hpp->latency_timer); > pci_read_config_word(dev, PCI_BRIDGE_CONTROL, > &pci_bctl); > - if (hpp->enable_serr) > - pci_bctl |= PCI_BRIDGE_CTL_SERR; > if (hpp->enable_perr) > pci_bctl |= PCI_BRIDGE_CTL_PARITY; > pci_write_config_word(dev, PCI_BRIDGE_CONTROL, > pci_bctl); @@ -2114,6 +2112,23 @@ static void > pci_configure_eetlp_prefix(struct pci_dev *dev) #endif } > > +static void pci_configure_serr(struct pci_dev *dev) { > + if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) { > + u16 control; > + > + /* > + * A Type-1 PCI bridge will not forward ERR_ messages > coming > + * from an endpoint if SERR# forwarding is not enabled. > + */ > + pci_read_config_word(dev, PCI_BRIDGE_CONTROL, > &control); > + if (!(control & PCI_BRIDGE_CTL_SERR)) { > + control |= PCI_BRIDGE_CTL_SERR; > + pci_write_config_word(dev, PCI_BRIDGE_CONTROL, > control); > + } > + } > +} > + > static void pci_configure_device(struct pci_dev *dev) { > struct hotplug_params hpp; > @@ -2124,6 +2139,7 @@ static void pci_configure_device(struct pci_dev > *dev) > pci_configure_relaxed_ordering(dev); > pci_configure_ltr(dev); > pci_configure_eetlp_prefix(dev); > + pci_configure_serr(dev); > > memset(&hpp, 0, sizeof(hpp)); > ret = pci_get_hp_params(dev, &hpp); > -- > 2.7.4
[+cc others who have commented or been copied on this ancient issue] On Wed, Nov 14, 2018 at 08:17:01PM +0530, Bharat Kumar Gogada wrote: > As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages > will be forwarded from the secondary interface to the primary interface, > if the SERR# Enable bit in the Bridge Control register is set. > Currently PCI_BRIDGE_CTL_SERR is being enabled only in > ACPI flow. > This patch enables PCI_BRIDGE_CTL_SERR for Type-1 PCI device. I apologize for being so slow to respond to this. I applied it to pci/aer for v5.1 with the following changelog: PCI: Enable SERR# forwarding for all bridges As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages will be forwarded from the secondary interface to the primary interface, if the SERR# Enable bit in the Bridge Control register is set. It seems clear that an ACPI hotplug parameter method (_HPP or _HPX) that tells us to "enable SERR in the command register" (ACPI v6.2, sec 6.2.8, 6.2.9.1) refers to PCI_COMMAND_SERR, which enables reporting of errors by the function itself. For bridges, we also interpreted that to mean we should enable PCI_BRIDGE_CTL_SERR, which enables *forwarding* of errors by the bridge. But we didn't enable PCI_BRIDGE_CTL_SERR anywhere else, which means we never enabled it for non-ACPI systems or ACPI systems that didn't supply hotplug parameters. That means errors reported below bridges were often never forwarded up to a Root Port where they could be signaled via AER. Enable PCI_BRIDGE_CTL_SERR for all bridges so we can get better error reporting for downstream devices. Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> [bhelgaas: changelog] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> > Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> > --- > drivers/pci/probe.c | 20 ++++++++++++++++++-- > 1 file changed, 18 insertions(+), 2 deletions(-) > > diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c > index b1c05b5..ed71e8e 100644 > --- a/drivers/pci/probe.c > +++ b/drivers/pci/probe.c > @@ -1841,8 +1841,6 @@ static void program_hpp_type0(struct pci_dev *dev, struct hpp_type0 *hpp) > pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER, > hpp->latency_timer); > pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &pci_bctl); > - if (hpp->enable_serr) > - pci_bctl |= PCI_BRIDGE_CTL_SERR; > if (hpp->enable_perr) > pci_bctl |= PCI_BRIDGE_CTL_PARITY; > pci_write_config_word(dev, PCI_BRIDGE_CONTROL, pci_bctl); > @@ -2114,6 +2112,23 @@ static void pci_configure_eetlp_prefix(struct pci_dev *dev) > #endif > } > > +static void pci_configure_serr(struct pci_dev *dev) > +{ > + if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) { > + u16 control; > + > + /* > + * A Type-1 PCI bridge will not forward ERR_ messages coming > + * from an endpoint if SERR# forwarding is not enabled. > + */ > + pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &control); > + if (!(control & PCI_BRIDGE_CTL_SERR)) { > + control |= PCI_BRIDGE_CTL_SERR; > + pci_write_config_word(dev, PCI_BRIDGE_CONTROL, control); > + } > + } > +} > + > static void pci_configure_device(struct pci_dev *dev) > { > struct hotplug_params hpp; > @@ -2124,6 +2139,7 @@ static void pci_configure_device(struct pci_dev *dev) > pci_configure_relaxed_ordering(dev); > pci_configure_ltr(dev); > pci_configure_eetlp_prefix(dev); > + pci_configure_serr(dev); > > memset(&hpp, 0, sizeof(hpp)); > ret = pci_get_hp_params(dev, &hpp); > -- > 2.7.4 >
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index b1c05b5..ed71e8e 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -1841,8 +1841,6 @@ static void program_hpp_type0(struct pci_dev *dev, struct hpp_type0 *hpp) pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER, hpp->latency_timer); pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &pci_bctl); - if (hpp->enable_serr) - pci_bctl |= PCI_BRIDGE_CTL_SERR; if (hpp->enable_perr) pci_bctl |= PCI_BRIDGE_CTL_PARITY; pci_write_config_word(dev, PCI_BRIDGE_CONTROL, pci_bctl); @@ -2114,6 +2112,23 @@ static void pci_configure_eetlp_prefix(struct pci_dev *dev) #endif } +static void pci_configure_serr(struct pci_dev *dev) +{ + if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) { + u16 control; + + /* + * A Type-1 PCI bridge will not forward ERR_ messages coming + * from an endpoint if SERR# forwarding is not enabled. + */ + pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &control); + if (!(control & PCI_BRIDGE_CTL_SERR)) { + control |= PCI_BRIDGE_CTL_SERR; + pci_write_config_word(dev, PCI_BRIDGE_CONTROL, control); + } + } +} + static void pci_configure_device(struct pci_dev *dev) { struct hotplug_params hpp; @@ -2124,6 +2139,7 @@ static void pci_configure_device(struct pci_dev *dev) pci_configure_relaxed_ordering(dev); pci_configure_ltr(dev); pci_configure_eetlp_prefix(dev); + pci_configure_serr(dev); memset(&hpp, 0, sizeof(hpp)); ret = pci_get_hp_params(dev, &hpp);
As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages will be forwarded from the secondary interface to the primary interface, if the SERR# Enable bit in the Bridge Control register is set. Currently PCI_BRIDGE_CTL_SERR is being enabled only in ACPI flow. This patch enables PCI_BRIDGE_CTL_SERR for Type-1 PCI device. Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> --- drivers/pci/probe.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-)