diff mbox series

[v3,01/40] cxl: Rename CXL_MEM to CXL_PCI

Message ID 164298412409.3018233.12407355692407890752.stgit@dwillia2-desk3.amr.corp.intel.com (mailing list archive)
State Not Applicable
Delegated to: Bjorn Helgaas
Headers show
Series CXL.mem Topology Discovery and Hotplug Support | expand

Commit Message

Dan Williams Jan. 24, 2022, 12:28 a.m. UTC 
From: Ben Widawsky <ben.widawsky@intel.com>

The cxl_mem module was renamed cxl_pci in commit 21e9f76733a8 ("cxl:
Rename mem to pci"). In preparation for adding an ancillary driver for
cxl_memdev devices (registered on the cxl bus by cxl_pci), go ahead and
rename CONFIG_CXL_MEM to CONFIG_CXL_PCI. Free up the CXL_MEM name for
that new driver to manage CXL.mem endpoint operations.

Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/cxl/Kconfig  |   23 ++++++++++++-----------
 drivers/cxl/Makefile |    2 +-
 2 files changed, 13 insertions(+), 12 deletions(-)
diff mbox series

Patch

diff --git a/drivers/cxl/Kconfig b/drivers/cxl/Kconfig
index 67c91378f2dd..ef05e96f8f97 100644
--- a/drivers/cxl/Kconfig
+++ b/drivers/cxl/Kconfig
@@ -13,25 +13,26 @@  menuconfig CXL_BUS
 
 if CXL_BUS
 
-config CXL_MEM
-	tristate "CXL.mem: Memory Devices"
+config CXL_PCI
+	tristate "PCI manageability"
 	default CXL_BUS
 	help
-	  The CXL.mem protocol allows a device to act as a provider of
-	  "System RAM" and/or "Persistent Memory" that is fully coherent
-	  as if the memory was attached to the typical CPU memory
-	  controller.
+	  The CXL specification defines a "CXL memory device" sub-class in the
+	  PCI "memory controller" base class of devices. Device's identified by
+	  this class code provide support for volatile and / or persistent
+	  memory to be mapped into the system address map (Host-managed Device
+	  Memory (HDM)).
 
-	  Say 'y/m' to enable a driver that will attach to CXL.mem devices for
-	  configuration and management primarily via the mailbox interface. See
-	  Chapter 2.3 Type 3 CXL Device in the CXL 2.0 specification for more
-	  details.
+	  Say 'y/m' to enable a driver that will attach to CXL memory expander
+	  devices enumerated by the memory device class code for configuration
+	  and management primarily via the mailbox interface. See Chapter 2.3
+	  Type 3 CXL Device in the CXL 2.0 specification for more details.
 
 	  If unsure say 'm'.
 
 config CXL_MEM_RAW_COMMANDS
 	bool "RAW Command Interface for Memory Devices"
-	depends on CXL_MEM
+	depends on CXL_PCI
 	help
 	  Enable CXL RAW command interface.
 
diff --git a/drivers/cxl/Makefile b/drivers/cxl/Makefile
index d1aaabc940f3..cf07ae6cea17 100644
--- a/drivers/cxl/Makefile
+++ b/drivers/cxl/Makefile
@@ -1,6 +1,6 @@ 
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_CXL_BUS) += core/
-obj-$(CONFIG_CXL_MEM) += cxl_pci.o
+obj-$(CONFIG_CXL_PCI) += cxl_pci.o
 obj-$(CONFIG_CXL_ACPI) += cxl_acpi.o
 obj-$(CONFIG_CXL_PMEM) += cxl_pmem.o