Message ID | 1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com (mailing list archive) |
---|---|
State | Accepted |
Delegated to: | Lorenzo Pieralisi |
Headers | show |
Series | [v2] PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present | expand |
Hi Lucas: This patch is pending for a while. Can you help to take look at it and give the ack if you don't have comments on it? Thank you in advanced. Best Regards Richard Zhu > -----Original Message----- > From: Richard Zhu <hongxing.zhu@nxp.com> > Sent: 2022年2月24日 11:07 > To: l.stach@pengutronix.de; bhelgaas@google.com; > lorenzo.pieralisi@arm.com > Cc: linux-pci@vger.kernel.org; linux-arm-kernel@lists.infradead.org; > linux-kernel@vger.kernel.org; kernel@pengutronix.de; dl-linux-imx > <linux-imx@nxp.com>; Hongxing Zhu <hongxing.zhu@nxp.com> > Subject: [PATCH v2] PCI: imx6: Assert i.MX8MM CLKREQ# even if no device > present > > The CLKREQ# signal is an open drain, active low signal that is driven low by the > remote Endpoint device. But it might not be driven low if no Endpoint device is > connected. > > On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no > Endpoint is connected to assert CLKREQ#. > > Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the PHY > can be initialized. > > Fixes: 178e244cb6e2 ("PCI: imx: Add the imx8mm pcie support") > Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> > --- > drivers/pci/controller/dwc/pci-imx6.c | 4 ---- > 1 file changed, 4 deletions(-) > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c > b/drivers/pci/controller/dwc/pci-imx6.c > index 78e32a539060..168cb1287ba9 100644 > --- a/drivers/pci/controller/dwc/pci-imx6.c > +++ b/drivers/pci/controller/dwc/pci-imx6.c > @@ -447,10 +447,6 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie > *imx6_pcie) > case IMX7D: > break; > case IMX8MM: > - ret = clk_prepare_enable(imx6_pcie->pcie_aux); > - if (ret) > - dev_err(dev, "unable to enable pcie_aux clock\n"); > - break; > case IMX8MQ: > ret = clk_prepare_enable(imx6_pcie->pcie_aux); > if (ret) { > -- > 2.25.1
Am Donnerstag, dem 24.02.2022 um 11:06 +0800 schrieb Richard Zhu: > The CLKREQ# signal is an open drain, active low signal that is driven > low by the remote Endpoint device. But it might not be driven low if no > Endpoint device is connected. > > On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no > Endpoint is connected to assert CLKREQ#. > > Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the > PHY can be initialized. > > Fixes: 178e244cb6e2 ("PCI: imx: Add the imx8mm pcie support") > Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > --- > drivers/pci/controller/dwc/pci-imx6.c | 4 ---- > 1 file changed, 4 deletions(-) > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c > index 78e32a539060..168cb1287ba9 100644 > --- a/drivers/pci/controller/dwc/pci-imx6.c > +++ b/drivers/pci/controller/dwc/pci-imx6.c > @@ -447,10 +447,6 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie) > case IMX7D: > break; > case IMX8MM: > - ret = clk_prepare_enable(imx6_pcie->pcie_aux); > - if (ret) > - dev_err(dev, "unable to enable pcie_aux clock\n"); > - break; > case IMX8MQ: > ret = clk_prepare_enable(imx6_pcie->pcie_aux); > if (ret) {
On Thu, 24 Feb 2022 11:06:53 +0800, Richard Zhu wrote: > The CLKREQ# signal is an open drain, active low signal that is driven > low by the remote Endpoint device. But it might not be driven low if no > Endpoint device is connected. > > On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no > Endpoint is connected to assert CLKREQ#. > > [...] Applied to pci/imx6, thanks! [1/1] PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present https://git.kernel.org/lpieralisi/pci/c/45514f78c6 Thanks, Lorenzo
diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c index 78e32a539060..168cb1287ba9 100644 --- a/drivers/pci/controller/dwc/pci-imx6.c +++ b/drivers/pci/controller/dwc/pci-imx6.c @@ -447,10 +447,6 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie) case IMX7D: break; case IMX8MM: - ret = clk_prepare_enable(imx6_pcie->pcie_aux); - if (ret) - dev_err(dev, "unable to enable pcie_aux clock\n"); - break; case IMX8MQ: ret = clk_prepare_enable(imx6_pcie->pcie_aux); if (ret) {
The CLKREQ# signal is an open drain, active low signal that is driven low by the remote Endpoint device. But it might not be driven low if no Endpoint device is connected. On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no Endpoint is connected to assert CLKREQ#. Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the PHY can be initialized. Fixes: 178e244cb6e2 ("PCI: imx: Add the imx8mm pcie support") Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> --- drivers/pci/controller/dwc/pci-imx6.c | 4 ---- 1 file changed, 4 deletions(-)