@@ -55,16 +55,16 @@ enum {
static int use_msr;
-static int cs5536_read(struct pci_dev *pdev, int reg, u32 *val)
+static void cs5536_read(struct pci_dev *pdev, int reg, u32 *val)
{
if (unlikely(use_msr)) {
u32 dummy;
rdmsr(MSR_IDE_CFG + reg, *val, dummy);
- return 0;
+ return;
}
- return pci_read_config_dword(pdev, PCI_IDE_CFG + reg * 4, val);
+ pci_read_config_dword(pdev, PCI_IDE_CFG + reg * 4, val);
}
static int cs5536_write(struct pci_dev *pdev, int reg, int val)
@@ -27,7 +27,8 @@ static int rz1000_disable_readahead(struct pci_dev *dev)
{
u16 reg;
- if (!pci_read_config_word (dev, 0x40, ®) &&
+ pci_read_config_word(dev, 0x40, ®);
+ if ((reg != (u16)~0) &&
!pci_write_config_word(dev, 0x40, reg & 0xdfff)) {
printk(KERN_INFO "%s: disabled chipset read-ahead "
"(buggy RZ1000/RZ1001)\n", pci_name(dev));
@@ -37,7 +37,8 @@ static int ide_setup_pci_baseregs(struct pci_dev *dev, const char *name)
/*
* Place both IDE interfaces into PCI "native" mode:
*/
- if (pci_read_config_byte(dev, PCI_CLASS_PROG, &progif) ||
+ pci_read_config_byte(dev, PCI_CLASS_PROG, &progif);
+ if ((progif == (u8)~0) ||
(progif & 5) != 5) {
if ((progif & 0xa) != 0xa) {
printk(KERN_INFO "%s %s: device not capable of full "
@@ -47,7 +48,8 @@ static int ide_setup_pci_baseregs(struct pci_dev *dev, const char *name)
printk(KERN_INFO "%s %s: placing both ports into native PCI "
"mode\n", name, pci_name(dev));
(void) pci_write_config_byte(dev, PCI_CLASS_PROG, progif|5);
- if (pci_read_config_byte(dev, PCI_CLASS_PROG, &progif) ||
+ pci_read_config_byte(dev, PCI_CLASS_PROG, &progif);
+ if ((progif == (u8)~0) ||
(progif & 5) != 5) {
printk(KERN_ERR "%s %s: rewrite of PROGIF failed, "
"wanted 0x%04x, got 0x%04x\n",
@@ -251,7 +253,8 @@ static int ide_pci_configure(struct pci_dev *dev, const struct ide_port_info *d)
d->name, pci_name(dev));
return -ENODEV;
}
- if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd)) {
+ pci_read_config_word(dev, PCI_COMMAND, &pcicmd);
+ if (pcicmd == (u16)~0) {
printk(KERN_ERR "%s %s: error accessing PCI regs\n",
d->name, pci_name(dev));
return -EIO;
@@ -415,8 +418,8 @@ static int ide_setup_pci_controller(struct pci_dev *dev, int bars,
if (ret < 0)
goto out;
- ret = pci_read_config_word(dev, PCI_COMMAND, &pcicmd);
- if (ret < 0) {
+ pci_read_config_word(dev, PCI_COMMAND, &pcicmd);
+ if (pcicmd == (u16)~0) {
printk(KERN_ERR "%s %s: error accessing PCI regs\n",
d->name, pci_name(dev));
goto out_free_bars;
@@ -466,11 +469,14 @@ void ide_pci_setup_ports(struct pci_dev *dev, const struct ide_port_info *d,
for (port = 0; port < channels; ++port) {
const struct ide_pci_enablebit *e = &d->enablebits[port];
- if (e->reg && (pci_read_config_byte(dev, e->reg, &tmp) ||
- (tmp & e->mask) != e->val)) {
- printk(KERN_INFO "%s %s: IDE port disabled\n",
- d->name, pci_name(dev));
- continue; /* port not enabled */
+ if (e->reg) {
+ pci_read_config_byte(dev, e->reg, &tmp);
+
+ if ((tmp == (u8)~0) || ((tmp & e->mask) != e->val)) {
+ printk(KERN_INFO "%s %s: IDE port disabled\n",
+ d->name, pci_name(dev));
+ continue; /* port not enabled */
+ }
}
if (ide_hw_configure(dev, d, port, hw + port))
The return value of pci_read_config_*() may not indicate a device error. However, the value read by these functions is more likely to indicate this kind of error. This presents two overlapping ways of reporting errors and complicates error checking. It is possible to move to one single way of checking for error if the dependency on the return value of these functions is removed, then it can later be made to return void. Remove all uses of the return value of pci_read_config_*(). Check the actual value read for ~0. In this case, ~0 is an invalid value thus it indicates some kind of error. drivers/ide/cs5536.c cs5536_read() : None of the callers of cs5536_read() uses the return value. The obtained value can be checked for validity to confirm success. Change the return type of cs5536_read() to void. Suggested-by: Bjorn Helgaas <bjorn@helgaas.com> Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com> --- drivers/ide/cs5536.c | 6 +++--- drivers/ide/rz1000.c | 3 ++- drivers/ide/setup-pci.c | 26 ++++++++++++++++---------- 3 files changed, 21 insertions(+), 14 deletions(-)