@@ -31,8 +31,14 @@ Required properties:
- reg: base addresses and lengths of the PCIe controller register blocks.
- interrupts: A list of interrupt outputs of the controller. Must contain an
entry for each entry in the interrupt-names property.
-- interrupt-names: Must include the following entries:
- "intr": The interrupt that is asserted for controller interrupts
+- interrupt-names: It could include the following entries:
+ "aer": Used for interrupt line which reports AER events when
+ non MSI/MSI-X/INTx mode is used
+ "pme": Used for interrupt line which reports PME events when
+ non MSI/MSI-X/INTx mode is used
+ "intr": Used for SoCs(like ls2080a, lx2160a, ls2080a, ls2088a, ls1088a)
+ which has a single interrupt line for miscellaneous controller
+ events(could include AER and PME events).
- fsl,pcie-scfg: Must include two entries.
The first entry must be a link to the SCFG device node
The second entry is the physical PCIe controller index starting from '0'.
@@ -48,26 +54,28 @@ Optional properties:
Example:
pcie@3400000 {
- compatible = "fsl,ls1021a-pcie";
- reg = <0x00 0x03400000 0x0 0x00010000 /* controller registers */
- 0x40 0x00000000 0x0 0x00002000>; /* configuration space */
+ compatible = "fsl,ls2088a-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x80 0x00000000 0x0 0x00002000>; /* configuration space */
reg-names = "regs", "config";
- interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
- interrupt-names = "intr";
- fsl,pcie-scfg = <&scfg 0>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+ interrupt-names = "aer", "pme", "intr";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
dma-coherent;
- num-lanes = <4>;
+ num-viewport = <8>;
bus-range = <0x0 0xff>;
- ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
- 0xc2000000 0x0 0x20000000 0x40 0x20000000 0x0 0x20000000 /* prefetchable memory */
- 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000
+ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&its>;
+ iommu-map = <0 &smmu 0 1>; /* This is fixed-up by u-boot */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
- interrupt-map = <0000 0 0 1 &gic GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
- <0000 0 0 2 &gic GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
- <0000 0 0 3 &gic GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
- <0000 0 0 4 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
};
Different platforms using this controller are using different numbers of interrupt lines and the routing of events to these interrupt lines are different too. So instead of trying to define names for these interrupt lines, we define the more specific AER/PME events that are routed to these interrupt lines. For platforms which only has a single interrupt line for miscellaneous controller events, we can keep using the original "intr" name for backward compatibility. Also change the example from ls1021a to ls2088a for better representation. Signed-off-by: Li Yang <leoyang.li@nxp.com> --- .../bindings/pci/layerscape-pci.txt | 40 +++++++++++-------- 1 file changed, 24 insertions(+), 16 deletions(-)