| Message ID | 20220414074011.500533-3-herve.codina@bootlin.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | RZN1 USB Host support | expand |
Hi Hervé, herve.codina@bootlin.com wrote on Thu, 14 Apr 2022 09:40:05 +0200: > Convert Renesas PCI bridge bindings documentation to json-schema. > Also name it 'renesas,pci-usb' as it is specifically used to > connect the PCI USB controllers to AHB bus. > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > --- > .../devicetree/bindings/pci/pci-rcar-gen2.txt | 84 ----------- > .../bindings/pci/renesas,pci-usb.yaml | 134 ++++++++++++++++++ > 2 files changed, 134 insertions(+), 84 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > create mode 100644 Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > deleted file mode 100644 > index aeba38f0a387..000000000000 > --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > +++ /dev/null > @@ -1,84 +0,0 @@ > -Renesas AHB to PCI bridge > -------------------------- > - > -This is the bridge used internally to connect the USB controllers to the > -AHB. There is one bridge instance per USB port connected to the internal > -OHCI and EHCI controllers. > - > -Required properties: > -- compatible: "renesas,pci-r8a7742" for the R8A7742 SoC; > - "renesas,pci-r8a7743" for the R8A7743 SoC; > - "renesas,pci-r8a7744" for the R8A7744 SoC; > - "renesas,pci-r8a7745" for the R8A7745 SoC; > - "renesas,pci-r8a7790" for the R8A7790 SoC; > - "renesas,pci-r8a7791" for the R8A7791 SoC; > - "renesas,pci-r8a7793" for the R8A7793 SoC; > - "renesas,pci-r8a7794" for the R8A7794 SoC; > - "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or > - RZ/G1 compatible device. > - > - > - When compatible with the generic version, nodes must list the > - SoC-specific version corresponding to the platform first > - followed by the generic version. > - > -- reg: A list of physical regions to access the device: the first is > - the operational registers for the OHCI/EHCI controllers and the > - second is for the bridge configuration and control registers. > -- interrupts: interrupt for the device. > -- clocks: The reference to the device clock. > -- bus-range: The PCI bus number range; as this is a single bus, the range > - should be specified as the same value twice. > -- #address-cells: must be 3. > -- #size-cells: must be 2. > -- #interrupt-cells: must be 1. > -- interrupt-map: standard property used to define the mapping of the PCI > - interrupts to the GIC interrupts. > -- interrupt-map-mask: standard property that helps to define the interrupt > - mapping. > - > -Optional properties: > -- dma-ranges: a single range for the inbound memory region. If not supplied, > - defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the > - allowed combinations of address and size. > - > -Example SoC configuration: > - > - pci0: pci@ee090000 { > - compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; > - clocks = <&mstp7_clks R8A7790_CLK_EHCI>; > - reg = <0x0 0xee090000 0x0 0xc00>, > - <0x0 0xee080000 0x0 0x1100>; > - interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - > - bus-range = <0 0>; > - #address-cells = <3>; > - #size-cells = <2>; > - #interrupt-cells = <1>; > - dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; > - interrupt-map-mask = <0xff00 0 0 0x7>; > - interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH > - 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH > - 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; > - > - usb@1,0 { > - reg = <0x800 0 0 0 0>; > - phys = <&usb0 0>; > - phy-names = "usb"; > - }; > - > - usb@2,0 { > - reg = <0x1000 0 0 0 0>; > - phys = <&usb0 0>; > - phy-names = "usb"; > - }; > - }; > - > -Example board setup: > - > -&pci0 { > - status = "okay"; > - pinctrl-0 = <&usb0_pins>; > - pinctrl-names = "default"; > -}; > diff --git a/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > new file mode 100644 > index 000000000000..3f8d79b746c7 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > @@ -0,0 +1,134 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pci/renesas,pci-usb.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Renesas AHB to PCI bridge > + > +maintainers: > + - Marek Vasut <marek.vasut+renesas@gmail.com> > + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> > + > +description: | > + This is the bridge used internally to connect the USB controllers to the > + AHB. There is one bridge instance per USB port connected to the internal > + OHCI and EHCI controllers. > + > +allOf: > + - $ref: /schemas/pci/pci-bus.yaml# > + > +properties: > + compatible: > + oneOf: > + - items: > + - enum: > + - renesas,pci-r8a7742 # RZ/G1H > + - renesas,pci-r8a7743 # RZ/G1M > + - renesas,pci-r8a7744 # RZ/G1N > + - renesas,pci-r8a7745 # RZ/G1E > + - renesas,pci-r8a7790 # R-Car H2 > + - renesas,pci-r8a7791 # R-Car M2-W > + - renesas,pci-r8a7793 # R-Car M2-N > + - renesas,pci-r8a7794 # R-Car E2 > + - const: renesas,pci-rcar-gen2 # R-Car Gen2 and RZ/G1 > + > + reg: > + description: | > + A list of physical regions to access the device. The first is > + the operational registers for the OHCI/EHCI controllers and the > + second is for the bridge configuration and control registers. > + minItems: 2 > + maxItems: 2 > + > + interrupts: > + description: Interrupt for the device. When the description is rather straightforward (like "this is the main interrupt/clock") I don't think a description is expected. A number however might be useful, I believe. > + > + interrupt-map: > + description: | > + Standard property used to define the mapping of the PCI interrupts > + to the GIC interrupts. > + > + interrupt-map-mask: > + description: > + Standard property that helps to define the interrupt mapping. > + > + clocks: > + description: The reference to the device clock. Maybe maxItems: 1 ? > + > + bus-range: > + description: | > + The PCI bus number range; as this is a single bus, the range > + should be specified as the same value twice. > + > + "#address-cells": > + const: 3 > + > + "#size-cells": > + const: 2 > + > + "#interrupt-cells": > + const: 1 > + > + dma-ranges: > + description: | > + A single range for the inbound memory region. If not supplied, > + defaults to 1GiB at 0x40000000. Note there are hardware restrictions on > + the allowed combinations of address and size. > + > +required: > + - compatible > + - reg > + - interrupts > + - interrupt-map > + - interrupt-map-mask > + - clocks > + - bus-range > + - "#address-cells" > + - "#size-cells" > + - "#interrupt-cells" > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> > + > + bus { > + #address-cells = <2>; > + #size-cells = <2>; > + > + pci0: pci@ee090000 { > + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; > + device_type = "pci"; > + clocks = <&cpg CPG_MOD 703>; > + reg = <0 0xee090000 0 0xc00>, > + <0 0xee080000 0 0x1100>; > + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + > + bus-range = <0 0>; > + #address-cells = <3>; > + #size-cells = <2>; > + #interrupt-cells = <1>; > + ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>; > + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; > + interrupt-map-mask = <0xf800 0 0 0x7>; > + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > + <0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > + <0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > + > + usb@1,0 { > + reg = <0x800 0 0 0 0>; > + phys = <&usb0 0>; > + phy-names = "usb"; > + }; > + > + usb@2,0 { > + reg = <0x1000 0 0 0 0>; > + phys = <&usb0 0>; > + phy-names = "usb"; > + }; > + }; > + }; Thanks, Miquèl
Hi Hervé, On Thu, Apr 14, 2022 at 9:40 AM Herve Codina <herve.codina@bootlin.com> wrote: > Convert Renesas PCI bridge bindings documentation to json-schema. > Also name it 'renesas,pci-usb' as it is specifically used to > connect the PCI USB controllers to AHB bus. > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> Thanks a lot for tackling this DT binding file! > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > @@ -0,0 +1,134 @@ > +# SPDX-License-Identifier: GPL-2.0 scripts/checkpatch.pl says: WARNING: DT binding documents should be licensed (GPL-2.0-only OR BSD-2-Clause) > + reg: > + description: | > + A list of physical regions to access the device. The first is > + the operational registers for the OHCI/EHCI controllers and the > + second is for the bridge configuration and control registers. > + minItems: 2 > + maxItems: 2 reg: items: - description: Operational registers for the OHCI/EHCI controllers. - description: Bridge configuration and control registers. > + > + interrupts: > + description: Interrupt for the device. maxItems: 1 The description is not needed. > + > + interrupt-map: > + description: | > + Standard property used to define the mapping of the PCI interrupts > + to the GIC interrupts. > + > + interrupt-map-mask: > + description: > + Standard property that helps to define the interrupt mapping. > + > + clocks: > + description: The reference to the device clock. maxItems: 1 The description is not needed. Missing "resets" and "power-domains" properties. Missing description of the child nodes. > +required: > + - compatible > + - reg > + - interrupts > + - interrupt-map > + - interrupt-map-mask > + - clocks Missing "resets" and "power-domains". > + - bus-range > + - "#address-cells" > + - "#size-cells" > + - "#interrupt-cells" > + > +unevaluatedProperties: false Why doesn't "make dtbs_check" complain about the presence of e.g. "resets" in the actual DTS files? > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> > + > + bus { > + #address-cells = <2>; > + #size-cells = <2>; I think you should drop this (and the corresponding high addresses below). > + > + pci0: pci@ee090000 { > + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; > + device_type = "pci"; > + clocks = <&cpg CPG_MOD 703>; > + reg = <0 0xee090000 0 0xc00>, > + <0 0xee080000 0 0x1100>; > + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; resets = <&cpg 703>; > + status = "disabled"; > + > + bus-range = <0 0>; > + #address-cells = <3>; > + #size-cells = <2>; > + #interrupt-cells = <1>; > + ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>; > + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; > + interrupt-map-mask = <0xf800 0 0 0x7>; > + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > + <0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > + <0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > + > + usb@1,0 { > + reg = <0x800 0 0 0 0>; > + phys = <&usb0 0>; > + phy-names = "usb"; > + }; > + ERROR: trailing whitespace #249: FILE: Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml:127: + $ > + usb@2,0 { > + reg = <0x1000 0 0 0 0>; > + phys = <&usb0 0>; > + phy-names = "usb"; > + }; > + }; > + }; Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
On Thu, Apr 14, 2022 at 09:40:05AM +0200, Herve Codina wrote: > Convert Renesas PCI bridge bindings documentation to json-schema. > Also name it 'renesas,pci-usb' as it is specifically used to > connect the PCI USB controllers to AHB bus. Please name it based on compatible strings. renesas,pci-rcar-gen2.yaml > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > --- > .../devicetree/bindings/pci/pci-rcar-gen2.txt | 84 ----------- > .../bindings/pci/renesas,pci-usb.yaml | 134 ++++++++++++++++++ > 2 files changed, 134 insertions(+), 84 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > create mode 100644 Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > deleted file mode 100644 > index aeba38f0a387..000000000000 > --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > +++ /dev/null > @@ -1,84 +0,0 @@ > -Renesas AHB to PCI bridge > -------------------------- > - > -This is the bridge used internally to connect the USB controllers to the > -AHB. There is one bridge instance per USB port connected to the internal > -OHCI and EHCI controllers. > - > -Required properties: > -- compatible: "renesas,pci-r8a7742" for the R8A7742 SoC; > - "renesas,pci-r8a7743" for the R8A7743 SoC; > - "renesas,pci-r8a7744" for the R8A7744 SoC; > - "renesas,pci-r8a7745" for the R8A7745 SoC; > - "renesas,pci-r8a7790" for the R8A7790 SoC; > - "renesas,pci-r8a7791" for the R8A7791 SoC; > - "renesas,pci-r8a7793" for the R8A7793 SoC; > - "renesas,pci-r8a7794" for the R8A7794 SoC; > - "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or > - RZ/G1 compatible device. > - > - > - When compatible with the generic version, nodes must list the > - SoC-specific version corresponding to the platform first > - followed by the generic version. > - > -- reg: A list of physical regions to access the device: the first is > - the operational registers for the OHCI/EHCI controllers and the > - second is for the bridge configuration and control registers. > -- interrupts: interrupt for the device. > -- clocks: The reference to the device clock. > -- bus-range: The PCI bus number range; as this is a single bus, the range > - should be specified as the same value twice. > -- #address-cells: must be 3. > -- #size-cells: must be 2. > -- #interrupt-cells: must be 1. > -- interrupt-map: standard property used to define the mapping of the PCI > - interrupts to the GIC interrupts. > -- interrupt-map-mask: standard property that helps to define the interrupt > - mapping. > - > -Optional properties: > -- dma-ranges: a single range for the inbound memory region. If not supplied, > - defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the > - allowed combinations of address and size. > - > -Example SoC configuration: > - > - pci0: pci@ee090000 { > - compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; > - clocks = <&mstp7_clks R8A7790_CLK_EHCI>; > - reg = <0x0 0xee090000 0x0 0xc00>, > - <0x0 0xee080000 0x0 0x1100>; > - interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - > - bus-range = <0 0>; > - #address-cells = <3>; > - #size-cells = <2>; > - #interrupt-cells = <1>; > - dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; > - interrupt-map-mask = <0xff00 0 0 0x7>; > - interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH > - 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH > - 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; > - > - usb@1,0 { > - reg = <0x800 0 0 0 0>; > - phys = <&usb0 0>; > - phy-names = "usb"; > - }; > - > - usb@2,0 { > - reg = <0x1000 0 0 0 0>; > - phys = <&usb0 0>; > - phy-names = "usb"; > - }; > - }; > - > -Example board setup: > - > -&pci0 { > - status = "okay"; > - pinctrl-0 = <&usb0_pins>; > - pinctrl-names = "default"; > -}; > diff --git a/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > new file mode 100644 > index 000000000000..3f8d79b746c7 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > @@ -0,0 +1,134 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pci/renesas,pci-usb.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Renesas AHB to PCI bridge > + > +maintainers: > + - Marek Vasut <marek.vasut+renesas@gmail.com> > + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> > + > +description: | > + This is the bridge used internally to connect the USB controllers to the > + AHB. There is one bridge instance per USB port connected to the internal > + OHCI and EHCI controllers. > + > +allOf: > + - $ref: /schemas/pci/pci-bus.yaml# > + > +properties: > + compatible: > + oneOf: > + - items: > + - enum: > + - renesas,pci-r8a7742 # RZ/G1H > + - renesas,pci-r8a7743 # RZ/G1M > + - renesas,pci-r8a7744 # RZ/G1N > + - renesas,pci-r8a7745 # RZ/G1E > + - renesas,pci-r8a7790 # R-Car H2 > + - renesas,pci-r8a7791 # R-Car M2-W > + - renesas,pci-r8a7793 # R-Car M2-N > + - renesas,pci-r8a7794 # R-Car E2 > + - const: renesas,pci-rcar-gen2 # R-Car Gen2 and RZ/G1 > + > + reg: > + description: | > + A list of physical regions to access the device. The first is > + the operational registers for the OHCI/EHCI controllers and the > + second is for the bridge configuration and control registers. > + minItems: 2 > + maxItems: 2 > + > + interrupts: > + description: Interrupt for the device. > + > + interrupt-map: > + description: | > + Standard property used to define the mapping of the PCI interrupts > + to the GIC interrupts. > + > + interrupt-map-mask: > + description: > + Standard property that helps to define the interrupt mapping. > + > + clocks: > + description: The reference to the device clock. > + > + bus-range: > + description: | > + The PCI bus number range; as this is a single bus, the range > + should be specified as the same value twice. items: const: 0 > + > + "#address-cells": > + const: 3 > + > + "#size-cells": > + const: 2 > + > + "#interrupt-cells": > + const: 1 All these are defined by pci-bus.yaml > + > + dma-ranges: > + description: | > + A single range for the inbound memory region. If not supplied, > + defaults to 1GiB at 0x40000000. Note there are hardware restrictions on > + the allowed combinations of address and size. 'a single range' == 'maxItems: 1' > + > +required: > + - compatible > + - reg > + - interrupts > + - interrupt-map > + - interrupt-map-mask > + - clocks > + - bus-range > + - "#address-cells" > + - "#size-cells" > + - "#interrupt-cells" > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> > + > + bus { > + #address-cells = <2>; > + #size-cells = <2>; > + > + pci0: pci@ee090000 { > + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; > + device_type = "pci"; > + clocks = <&cpg CPG_MOD 703>; > + reg = <0 0xee090000 0 0xc00>, > + <0 0xee080000 0 0x1100>; > + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; Don't disable your example. > + > + bus-range = <0 0>; > + #address-cells = <3>; > + #size-cells = <2>; > + #interrupt-cells = <1>; > + ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>; > + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; > + interrupt-map-mask = <0xf800 0 0 0x7>; > + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > + <0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > + <0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > + > + usb@1,0 { > + reg = <0x800 0 0 0 0>; > + phys = <&usb0 0>; > + phy-names = "usb"; > + }; > + > + usb@2,0 { > + reg = <0x1000 0 0 0 0>; > + phys = <&usb0 0>; > + phy-names = "usb"; > + }; > + }; > + }; > -- > 2.35.1 > >
Hi Geert, On Thu, 14 Apr 2022 10:28:47 +0200 Geert Uytterhoeven <geert@linux-m68k.org> wrote: > Hi Hervé, > > On Thu, Apr 14, 2022 at 9:40 AM Herve Codina <herve.codina@bootlin.com> wrote: > > Convert Renesas PCI bridge bindings documentation to json-schema. > > Also name it 'renesas,pci-usb' as it is specifically used to > > connect the PCI USB controllers to AHB bus. > > > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > > Thanks a lot for tackling this DT binding file! > > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > @@ -0,0 +1,134 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > scripts/checkpatch.pl says: > WARNING: DT binding documents should be licensed (GPL-2.0-only OR BSD-2-Clause) Right, changed to "GPL-2.0-only OR BSD-2-Clause" > > > + reg: > > + description: | > > + A list of physical regions to access the device. The first is > > + the operational registers for the OHCI/EHCI controllers and the > > + second is for the bridge configuration and control registers. > > + minItems: 2 > > + maxItems: 2 > > reg: > items: > - description: Operational registers for the OHCI/EHCI controllers. > - description: Bridge configuration and control registers. Ok, changed. > > > + > > + interrupts: > > + description: Interrupt for the device. > > maxItems: 1 > > The description is not needed. Ok, changed. > > > + > > + interrupt-map: > > + description: | > > + Standard property used to define the mapping of the PCI interrupts > > + to the GIC interrupts. > > + > > + interrupt-map-mask: > > + description: > > + Standard property that helps to define the interrupt mapping. > > + > > + clocks: > > + description: The reference to the device clock. > > maxItems: 1 > > The description is not needed. Ok, changed > > Missing "resets" and "power-domains" properties. > > Missing description of the child nodes. "resets", "power-domains" dans child nodes added > > > +required: > > + - compatible > > + - reg > > + - interrupts > > + - interrupt-map > > + - interrupt-map-mask > > + - clocks > > Missing "resets" and "power-domains". Added > > > + - bus-range > > + - "#address-cells" > > + - "#size-cells" > > + - "#interrupt-cells" > > + > > +unevaluatedProperties: false > > Why doesn't "make dtbs_check" complain about the presence of > e.g. "resets" in the actual DTS files? > > > + > > +examples: > > + - | > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> > > + > > + bus { > > + #address-cells = <2>; > > + #size-cells = <2>; > > I think you should drop this (and the corresponding high addresses > below). > Ok > > + > > + pci0: pci@ee090000 { > > + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; > > + device_type = "pci"; > > + clocks = <&cpg CPG_MOD 703>; > > + reg = <0 0xee090000 0 0xc00>, > > + <0 0xee080000 0 0x1100>; > > + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > > power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; > resets = <&cpg 703>; Ok > > > + status = "disabled"; > > + > > + bus-range = <0 0>; > > + #address-cells = <3>; > > + #size-cells = <2>; > > + #interrupt-cells = <1>; > > + ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>; > > + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; > > + interrupt-map-mask = <0xf800 0 0 0x7>; > > + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > > + <0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, > > + <0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > > + > > + usb@1,0 { > > + reg = <0x800 0 0 0 0>; > > + phys = <&usb0 0>; > > + phy-names = "usb"; > > + }; > > + > > ERROR: trailing whitespace > #249: FILE: Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml:127: > + $ Ok > > > + usb@2,0 { > > + reg = <0x1000 0 0 0 0>; > > + phys = <&usb0 0>; > > + phy-names = "usb"; > > + }; > > + }; > > + }; > > Gr{oetje,eeting}s, > > Geert > > -- > Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org > > In personal conversations with technical people, I call myself a hacker. But > when I'm talking to journalists I just say "programmer" or something like that. > -- Linus Torvalds Thanks for the review, Hervé
Hi Rob, On Thu, 14 Apr 2022 13:15:30 -0500 Rob Herring <robh@kernel.org> wrote: > On Thu, Apr 14, 2022 at 09:40:05AM +0200, Herve Codina wrote: > > Convert Renesas PCI bridge bindings documentation to json-schema. > > Also name it 'renesas,pci-usb' as it is specifically used to > > connect the PCI USB controllers to AHB bus. > > Please name it based on compatible strings. renesas,pci-rcar-gen2.yaml Ok, renamed. > > > > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > > --- > > .../devicetree/bindings/pci/pci-rcar-gen2.txt | 84 ----------- > > .../bindings/pci/renesas,pci-usb.yaml | 134 ++++++++++++++++++ > > 2 files changed, 134 insertions(+), 84 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > > create mode 100644 Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > > > diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > > deleted file mode 100644 ... > > diff --git a/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > new file mode 100644 ... > > index 000000000000..3f8d79b746c7 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > @@ -0,0 +1,134 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/pci/renesas,pci-usb.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Renesas AHB to PCI bridge > > + > > +maintainers: > > + - Marek Vasut <marek.vasut+renesas@gmail.com> > > + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> > > + > > +description: | > > + This is the bridge used internally to connect the USB controllers to the > > + AHB. There is one bridge instance per USB port connected to the internal > > + OHCI and EHCI controllers. > > + > > +allOf: > > + - $ref: /schemas/pci/pci-bus.yaml# > > + > > +properties: > > + compatible: > > + oneOf: > > + - items: > > + - enum: > > + - renesas,pci-r8a7742 # RZ/G1H > > + - renesas,pci-r8a7743 # RZ/G1M > > + - renesas,pci-r8a7744 # RZ/G1N > > + - renesas,pci-r8a7745 # RZ/G1E > > + - renesas,pci-r8a7790 # R-Car H2 > > + - renesas,pci-r8a7791 # R-Car M2-W > > + - renesas,pci-r8a7793 # R-Car M2-N > > + - renesas,pci-r8a7794 # R-Car E2 > > + - const: renesas,pci-rcar-gen2 # R-Car Gen2 and RZ/G1 > > + > > + reg: > > + description: | > > + A list of physical regions to access the device. The first is > > + the operational registers for the OHCI/EHCI controllers and the > > + second is for the bridge configuration and control registers. > > + minItems: 2 > > + maxItems: 2 > > + > > + interrupts: > > + description: Interrupt for the device. > > + > > + interrupt-map: > > + description: | > > + Standard property used to define the mapping of the PCI interrupts > > + to the GIC interrupts. > > + > > + interrupt-map-mask: > > + description: > > + Standard property that helps to define the interrupt mapping. > > + > > + clocks: > > + description: The reference to the device clock. > > + > > + bus-range: > > + description: | > > + The PCI bus number range; as this is a single bus, the range > > + should be specified as the same value twice. > > items: > const: 0 Well, some other values are present in some dtsi files such as 'bus_range = <1 1>;' or 'bus_range = <2 2>;' in r8a7742.dtsi. The constraint is to have the same value twice. Is there a way to specify this constraint ? > > > + > > + "#address-cells": > > + const: 3 > > + > > + "#size-cells": > > + const: 2 > > + > > + "#interrupt-cells": > > + const: 1 > > All these are defined by pci-bus.yaml Right. Replaced by: "#address-cells": true "#size-cells": true "#interrupt-cells": true Is that correct ? > > > + > > + dma-ranges: > > + description: | > > + A single range for the inbound memory region. If not supplied, > > + defaults to 1GiB at 0x40000000. Note there are hardware restrictions on > > + the allowed combinations of address and size. > > 'a single range' == 'maxItems: 1' Ok, maxItems added. > > + > > +required: > > + - compatible > > + - reg > > + - interrupts > > + - interrupt-map > > + - interrupt-map-mask > > + - clocks > > + - bus-range > > + - "#address-cells" > > + - "#size-cells" > > + - "#interrupt-cells" > > + > > +unevaluatedProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> > > + > > + bus { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + pci0: pci@ee090000 { > > + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; > > + device_type = "pci"; > > + clocks = <&cpg CPG_MOD 703>; > > + reg = <0 0xee090000 0 0xc00>, > > + <0 0xee080000 0 0x1100>; > > + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > > + status = "disabled"; > > Don't disable your example. Ok, done Thanks for the review. Hervé
On Wed, Apr 20, 2022 at 02:44:11PM +0200, Herve Codina wrote: > Hi Rob, > > On Thu, 14 Apr 2022 13:15:30 -0500 > Rob Herring <robh@kernel.org> wrote: > > > On Thu, Apr 14, 2022 at 09:40:05AM +0200, Herve Codina wrote: > > > Convert Renesas PCI bridge bindings documentation to json-schema. > > > Also name it 'renesas,pci-usb' as it is specifically used to > > > connect the PCI USB controllers to AHB bus. > > > > Please name it based on compatible strings. renesas,pci-rcar-gen2.yaml > > Ok, renamed. > > > > > > > > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > > > --- > > > .../devicetree/bindings/pci/pci-rcar-gen2.txt | 84 ----------- > > > .../bindings/pci/renesas,pci-usb.yaml | 134 ++++++++++++++++++ > > > 2 files changed, 134 insertions(+), 84 deletions(-) > > > delete mode 100644 Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > > > create mode 100644 Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > > > > > diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt > > > deleted file mode 100644 > ... > > > diff --git a/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > > new file mode 100644 > ... > > > index 000000000000..3f8d79b746c7 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml > > > @@ -0,0 +1,134 @@ > > > +# SPDX-License-Identifier: GPL-2.0 > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/pci/renesas,pci-usb.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: Renesas AHB to PCI bridge > > > + > > > +maintainers: > > > + - Marek Vasut <marek.vasut+renesas@gmail.com> > > > + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> > > > + > > > +description: | > > > + This is the bridge used internally to connect the USB controllers to the > > > + AHB. There is one bridge instance per USB port connected to the internal > > > + OHCI and EHCI controllers. > > > + > > > +allOf: > > > + - $ref: /schemas/pci/pci-bus.yaml# > > > + > > > +properties: > > > + compatible: > > > + oneOf: > > > + - items: > > > + - enum: > > > + - renesas,pci-r8a7742 # RZ/G1H > > > + - renesas,pci-r8a7743 # RZ/G1M > > > + - renesas,pci-r8a7744 # RZ/G1N > > > + - renesas,pci-r8a7745 # RZ/G1E > > > + - renesas,pci-r8a7790 # R-Car H2 > > > + - renesas,pci-r8a7791 # R-Car M2-W > > > + - renesas,pci-r8a7793 # R-Car M2-N > > > + - renesas,pci-r8a7794 # R-Car E2 > > > + - const: renesas,pci-rcar-gen2 # R-Car Gen2 and RZ/G1 > > > + > > > + reg: > > > + description: | > > > + A list of physical regions to access the device. The first is > > > + the operational registers for the OHCI/EHCI controllers and the > > > + second is for the bridge configuration and control registers. > > > + minItems: 2 > > > + maxItems: 2 > > > + > > > + interrupts: > > > + description: Interrupt for the device. > > > + > > > + interrupt-map: > > > + description: | > > > + Standard property used to define the mapping of the PCI interrupts > > > + to the GIC interrupts. > > > + > > > + interrupt-map-mask: > > > + description: > > > + Standard property that helps to define the interrupt mapping. > > > + > > > + clocks: > > > + description: The reference to the device clock. > > > + > > > + bus-range: > > > + description: | > > > + The PCI bus number range; as this is a single bus, the range > > > + should be specified as the same value twice. > > > > items: > > const: 0 > > Well, some other values are present in some dtsi files such as > 'bus_range = <1 1>;' or 'bus_range = <2 2>;' in r8a7742.dtsi. > > The constraint is to have the same value twice. Is there a way > to specify this constraint ? Yes, but probably not worthwhile. Just drop it as pci-bus.yaml already defines it. > > > + > > > + "#address-cells": > > > + const: 3 > > > + > > > + "#size-cells": > > > + const: 2 > > > + > > > + "#interrupt-cells": > > > + const: 1 > > > > All these are defined by pci-bus.yaml > > Right. > Replaced by: > > "#address-cells": true > "#size-cells": true > "#interrupt-cells": true > > Is that correct ? You can just drop them completely. Rob
Hi Rob, On Wed, 20 Apr 2022 08:18:50 -0500 Rob Herring <robh@kernel.org> wrote: ... > > > > + bus-range: > > > > + description: | > > > > + The PCI bus number range; as this is a single bus, the range > > > > + should be specified as the same value twice. > > > > > > items: > > > const: 0 > > > > Well, some other values are present in some dtsi files such as > > 'bus_range = <1 1>;' or 'bus_range = <2 2>;' in r8a7742.dtsi. > > > > The constraint is to have the same value twice. Is there a way > > to specify this constraint ? > > Yes, but probably not worthwhile. Just drop it as pci-bus.yaml already > defines it. Instead of fully dropping the property, don't you think that keeping the given description here can be a way to express that the same value is needed twice ? > > > > > + > > > > + "#address-cells": > > > > + const: 3 > > > > + > > > > + "#size-cells": > > > > + const: 2 > > > > + > > > > + "#interrupt-cells": > > > > + const: 1 > > > > > > All these are defined by pci-bus.yaml > > > > Right. > > Replaced by: > > > > "#address-cells": true > > "#size-cells": true > > "#interrupt-cells": true > > > > Is that correct ? > > You can just drop them completely. Ok for #address-cells and #size-cells but not for #interrupt-cells. Dropping #interrupt-cells makes 'make dtbindings_check' unhappy: --- 8< --- $ make dt_binding_check DT_SCHEMA_FILES=renesas,pci-rcar-gen2.yaml LINT Documentation/devicetree/bindings CHKDT Documentation/devicetree/bindings/processed-schema.json /home/hcodina/xxx/Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.yaml: properties: '#interrupt-cells' is a dependency of 'interrupt-map' from schema $id: http://devicetree.org/meta-schemas/interrupts.yaml# SCHEMA Documentation/devicetree/bindings/processed-schema.json /home/hcodina/xxx/Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.yaml: ignoring, error in schema: properties DTEX Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.example.dts DTC Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.example.dtb CHECK Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.example.dtb $ --- 8< --- So I keep "#interrupt-cells": true Regards, Hervé
On Wed, Apr 20, 2022 at 03:46:11PM +0200, Herve Codina wrote: > Hi Rob, > > On Wed, 20 Apr 2022 08:18:50 -0500 > Rob Herring <robh@kernel.org> wrote: > > ... > > > > > > + bus-range: > > > > > + description: | > > > > > + The PCI bus number range; as this is a single bus, the range > > > > > + should be specified as the same value twice. > > > > > > > > items: > > > > const: 0 > > > > > > Well, some other values are present in some dtsi files such as > > > 'bus_range = <1 1>;' or 'bus_range = <2 2>;' in r8a7742.dtsi. > > > > > > The constraint is to have the same value twice. Is there a way > > > to specify this constraint ? > > > > Yes, but probably not worthwhile. Just drop it as pci-bus.yaml already > > defines it. > > Instead of fully dropping the property, don't you think that keeping > the given description here can be a way to express that the same value > is needed twice ? Yeah, that's fine. > > > > > + "#address-cells": > > > > > + const: 3 > > > > > + > > > > > + "#size-cells": > > > > > + const: 2 > > > > > + > > > > > + "#interrupt-cells": > > > > > + const: 1 > > > > > > > > All these are defined by pci-bus.yaml > > > > > > Right. > > > Replaced by: > > > > > > "#address-cells": true > > > "#size-cells": true > > > "#interrupt-cells": true > > > > > > Is that correct ? > > > > You can just drop them completely. > > Ok for #address-cells and #size-cells but not for #interrupt-cells. > > Dropping #interrupt-cells makes 'make dtbindings_check' unhappy: > --- 8< --- > $ make dt_binding_check DT_SCHEMA_FILES=renesas,pci-rcar-gen2.yaml > LINT Documentation/devicetree/bindings > CHKDT Documentation/devicetree/bindings/processed-schema.json > /home/hcodina/xxx/Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.yaml: properties: '#interrupt-cells' is a dependency of 'interrupt-map' > from schema $id: http://devicetree.org/meta-schemas/interrupts.yaml# > SCHEMA Documentation/devicetree/bindings/processed-schema.json > /home/hcodina/xxx/Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.yaml: ignoring, error in schema: properties > DTEX Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.example.dts > DTC Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.example.dtb > CHECK Documentation/devicetree/bindings/pci/renesas,pci-rcar-gen2.example.dtb > $ > --- 8< --- > > So I keep > "#interrupt-cells": true You should also drop 'interrupt-map' and 'interrupt-map-mask'. Rob
diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt deleted file mode 100644 index aeba38f0a387..000000000000 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ /dev/null @@ -1,84 +0,0 @@ -Renesas AHB to PCI bridge -------------------------- - -This is the bridge used internally to connect the USB controllers to the -AHB. There is one bridge instance per USB port connected to the internal -OHCI and EHCI controllers. - -Required properties: -- compatible: "renesas,pci-r8a7742" for the R8A7742 SoC; - "renesas,pci-r8a7743" for the R8A7743 SoC; - "renesas,pci-r8a7744" for the R8A7744 SoC; - "renesas,pci-r8a7745" for the R8A7745 SoC; - "renesas,pci-r8a7790" for the R8A7790 SoC; - "renesas,pci-r8a7791" for the R8A7791 SoC; - "renesas,pci-r8a7793" for the R8A7793 SoC; - "renesas,pci-r8a7794" for the R8A7794 SoC; - "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or - RZ/G1 compatible device. - - - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first - followed by the generic version. - -- reg: A list of physical regions to access the device: the first is - the operational registers for the OHCI/EHCI controllers and the - second is for the bridge configuration and control registers. -- interrupts: interrupt for the device. -- clocks: The reference to the device clock. -- bus-range: The PCI bus number range; as this is a single bus, the range - should be specified as the same value twice. -- #address-cells: must be 3. -- #size-cells: must be 2. -- #interrupt-cells: must be 1. -- interrupt-map: standard property used to define the mapping of the PCI - interrupts to the GIC interrupts. -- interrupt-map-mask: standard property that helps to define the interrupt - mapping. - -Optional properties: -- dma-ranges: a single range for the inbound memory region. If not supplied, - defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the - allowed combinations of address and size. - -Example SoC configuration: - - pci0: pci@ee090000 { - compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; - clocks = <&mstp7_clks R8A7790_CLK_EHCI>; - reg = <0x0 0xee090000 0x0 0xc00>, - <0x0 0xee080000 0x0 0x1100>; - interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - - bus-range = <0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; - interrupt-map-mask = <0xff00 0 0 0x7>; - interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH - 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH - 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; - - usb@1,0 { - reg = <0x800 0 0 0 0>; - phys = <&usb0 0>; - phy-names = "usb"; - }; - - usb@2,0 { - reg = <0x1000 0 0 0 0>; - phys = <&usb0 0>; - phy-names = "usb"; - }; - }; - -Example board setup: - -&pci0 { - status = "okay"; - pinctrl-0 = <&usb0_pins>; - pinctrl-names = "default"; -}; diff --git a/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml new file mode 100644 index 000000000000..3f8d79b746c7 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/renesas,pci-usb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas AHB to PCI bridge + +maintainers: + - Marek Vasut <marek.vasut+renesas@gmail.com> + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + +description: | + This is the bridge used internally to connect the USB controllers to the + AHB. There is one bridge instance per USB port connected to the internal + OHCI and EHCI controllers. + +allOf: + - $ref: /schemas/pci/pci-bus.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,pci-r8a7742 # RZ/G1H + - renesas,pci-r8a7743 # RZ/G1M + - renesas,pci-r8a7744 # RZ/G1N + - renesas,pci-r8a7745 # RZ/G1E + - renesas,pci-r8a7790 # R-Car H2 + - renesas,pci-r8a7791 # R-Car M2-W + - renesas,pci-r8a7793 # R-Car M2-N + - renesas,pci-r8a7794 # R-Car E2 + - const: renesas,pci-rcar-gen2 # R-Car Gen2 and RZ/G1 + + reg: + description: | + A list of physical regions to access the device. The first is + the operational registers for the OHCI/EHCI controllers and the + second is for the bridge configuration and control registers. + minItems: 2 + maxItems: 2 + + interrupts: + description: Interrupt for the device. + + interrupt-map: + description: | + Standard property used to define the mapping of the PCI interrupts + to the GIC interrupts. + + interrupt-map-mask: + description: + Standard property that helps to define the interrupt mapping. + + clocks: + description: The reference to the device clock. + + bus-range: + description: | + The PCI bus number range; as this is a single bus, the range + should be specified as the same value twice. + + "#address-cells": + const: 3 + + "#size-cells": + const: 2 + + "#interrupt-cells": + const: 1 + + dma-ranges: + description: | + A single range for the inbound memory region. If not supplied, + defaults to 1GiB at 0x40000000. Note there are hardware restrictions on + the allowed combinations of address and size. + +required: + - compatible + - reg + - interrupts + - interrupt-map + - interrupt-map-mask + - clocks + - bus-range + - "#address-cells" + - "#size-cells" + - "#interrupt-cells" + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; + device_type = "pci"; + clocks = <&cpg CPG_MOD 703>; + reg = <0 0xee090000 0 0xc00>, + <0 0xee080000 0 0x1100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; + interrupt-map-mask = <0xf800 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, + <0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, + <0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + + usb@1,0 { + reg = <0x800 0 0 0 0>; + phys = <&usb0 0>; + phy-names = "usb"; + }; + + usb@2,0 { + reg = <0x1000 0 0 0 0>; + phys = <&usb0 0>; + phy-names = "usb"; + }; + }; + };
Convert Renesas PCI bridge bindings documentation to json-schema. Also name it 'renesas,pci-usb' as it is specifically used to connect the PCI USB controllers to AHB bus. Signed-off-by: Herve Codina <herve.codina@bootlin.com> --- .../devicetree/bindings/pci/pci-rcar-gen2.txt | 84 ----------- .../bindings/pci/renesas,pci-usb.yaml | 134 ++++++++++++++++++ 2 files changed, 134 insertions(+), 84 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt create mode 100644 Documentation/devicetree/bindings/pci/renesas,pci-usb.yaml