@@ -17,6 +17,25 @@ description:
select: false
properties:
+ interrupts:
+ description:
+ There are two main sub-blocks which are normally capable of
+ generating interrupts. It's System Information Interface and MSI
+ interface. While the former one has some common for the Host and
+ Endpoint controllers IRQ-signals, the later interface is obviously
+ Root Complex specific since it's responsible for the incoming MSI
+ messages signalling. The System Information IRQ signals are mainly
+ responsible for reporting the generic PCIe hierarchy and Root
+ Complex events like VPD IO request, general AER, PME, Hot-plug, link
+ bandwidth change, link equalization request, INTx asserted/deasserted
+ Message detection, embedded DMA Tx/Rx/Error.
+ minItems: 1
+ maxItems: 26
+
+ interrupt-names:
+ minItems: 1
+ maxItems: 26
+
phys:
description:
There can be up to the number of possible lanes PHYs specified placed in
@@ -41,6 +41,55 @@ properties:
items:
enum: [dbi, dbi2, config, atu, addr_space, link, atu_dma, appl]
+ interrupts:
+ description:
+ There is no mandatory IRQ signals for the normal controller functioning,
+ but in addition to the native set the platforms may have a link- or
+ PM-related IRQs specified.
+ minItems: 1
+ maxItems: 20
+
+ interrupt-names:
+ minItems: 1
+ maxItems: 20
+ items:
+ oneOf:
+ - description:
+ Controller request to read or write virtual product data
+ from/to the VPD capability registers.
+ const: vpd
+ - description:
+ Link Equalization Request flag is set in the Link Status 2
+ register (applicable if the corresponding IRQ is enabled in
+ the Link Control 3 register).
+ const: l_eq
+ - description:
+ Indicates that the eDMA Tx/Rx transfer is complete or that an
+ error has occurred on the corresponding channel. eDMA can have
+ eight Tx (Write) and Rx (Read) eDMA channels thus supporting up
+ to 16 IRQ signals all together. Write eDMA channels shall go
+ first in the ordered row as per default edma_int[*] bus setup.
+ pattern: '^dma([0-9]|1[0-5])?$'
+ - description:
+ PCIe protocol correctable error or a Data Path protection
+ correctable error is detected by the automotive/safety
+ feature.
+ const: sft_ce
+ - description:
+ Indicates that the internal safety mechanism has detected an
+ uncorrectable error.
+ const: sft_ue
+ - description:
+ Application-specific IRQ raised depending on the vendor-specific
+ events basis.
+ const: app
+ - description:
+ Vendor-specific IRQ names. Consider using the generic names above
+ for new bindings.
+ oneOf:
+ - description: See native "app" IRQ for details
+ enum: [ intr ]
+
max-functions:
maximum: 32
@@ -60,6 +109,9 @@ examples:
<0xd0000000 0x2000000>; /* Configuration space */
reg-names = "dbi", "dbi2", "addr_space";
+ interrupts = <23>, <24>;
+ interrupt-names = "dma0", "dma1";
+
phys = <&pcie_phy0>, <&pcie_phy1>, <&pcie_phy2>, <&pcie_phy3>;
phy-names = "pcie0", "pcie1", "pcie2", "pcie3";
@@ -42,9 +42,92 @@ properties:
enum: [ dbi, dbi2, config, atu, atu_dma, app, appl, elbi, mgmt, ctrl,
parf, cfg, link, ulreg, smu, mpu, apb, phy ]
- interrupts: true
-
- interrupt-names: true
+ interrupts:
+ description:
+ DWC PCIe Root Port/Complex specific IRQ signals. At least MSI interrupt
+ signal is supposed to be specified for the host controller.
+ minItems: 1
+ maxItems: 26
+
+ interrupt-names:
+ minItems: 1
+ maxItems: 26
+ items:
+ oneOf:
+ - description:
+ Controller request to read or write virtual product data
+ from/to the VPD capability registers.
+ const: vpd
+ - description:
+ Link Equalization Request flag is set in the Link Status 2
+ register (applicable if the corresponding IRQ is enabled in
+ the Link Control 3 register).
+ const: l_eq
+ - description:
+ Indicates that the eDMA Tx/Rx transfer is complete or that an
+ error has occurred on the corresponding channel. eDMA can have
+ eight Tx (Write) and Rx (Read) eDMA channels thus supporting up
+ to 16 IRQ signals all together. Write eDMA channels shall go
+ first in the ordered row as per default edma_int[*] bus setup.
+ pattern: '^dma([0-9]|1[0-5])?$'
+ - description:
+ PCIe protocol correctable error or a Data Path protection
+ correctable error is detected by the automotive/safety
+ feature.
+ const: sft_ce
+ - description:
+ Indicates that the internal safety mechanism has detected an
+ uncorrectable error.
+ const: sft_ue
+ - description:
+ Application-specific IRQ raised depending on the vendor-specific
+ events basis.
+ const: app
+ - description:
+ DSP AXI MSI Interrupt detected. It gets de-asserted when there is
+ no more MSI interrupt pending. The interrupt is relevant to the
+ iMSI-RX - Integrated MSI Receiver (AXI bridge).
+ const: msi
+ - description:
+ Legacy A/B/C/D interrupt signal. Basically it's triggered by
+ receiving a Assert_INT{A,B,C,D}/Desassert_INT{A,B,C,D} message
+ from the downstream device.
+ pattern: "^int(a|b|c|d)$"
+ - description:
+ Error condition detected and a flag is set in the Root Error Status
+ register of the AER capability. It's asserted when the RC
+ internally generated an error or an error message is received by
+ the RC.
+ const: aer
+ - description:
+ PME message is received by the port. That means having the PME
+ status bit set in the Root Status register (the event is
+ supposed to be unmasked in the Root Control register).
+ const: pme
+ - description:
+ Hot-plug event is detected. That is a bit has been set in the
+ Slot Status register and the corresponding event is enabled in
+ the Slot Control register.
+ const: hp
+ - description:
+ Link Autonomous Bandwidth Status flag has been set in the Link
+ Status register (the event is supposed to be unmasked in the
+ Link Control register).
+ const: bw_au
+ - description:
+ Bandwidth Management Status flag has been set in the Link
+ Status register (the event is supposed to be unmasked in the
+ Link Control register).
+ const: bw_mg
+ - description:
+ Vendor-specific IRQ names. Consider using the generic names above
+ for new bindings.
+ oneOf:
+ - description: See native "app" IRQ for details
+ enum: [ intr ]
+ allOf:
+ - contains:
+ const: msi
clocks: true
@@ -70,6 +153,7 @@ examples:
bus-range = <0x0 0xff>;
interrupts = <25>, <24>;
+ interrupt-names = "msi", "hp";
#interrupt-cells = <1>;
reset-gpios = <&port0 0 1>;