@@ -58,6 +58,126 @@ properties:
minItems: 1
maxItems: 26
+ clocks:
+ description:
+ DWC PCIe reference manual explicitly defines a set of the clocks required
+ to get the controller working correctly. In general all of them can
+ be divided into two groups':' application and core clocks. Note the
+ platforms may have some of the clock sources unspecified in case if the
+ corresponding domains are fed up from a common clock source.
+ minItems: 1
+ maxItems: 7
+
+ clock-names:
+ minItems: 1
+ maxItems: 7
+ items:
+ oneOf:
+ - description:
+ Data Bus Interface (DBI) clock. Clock signal for the AXI-bus
+ interface of the Configuration-Dependent Module, which is
+ basically the set of the controller CSRs.
+ const: dbi
+ - description:
+ Application AXI-bus Master interface clock. Basically this is
+ a clock for the controller DMA interface (PCI-to-CPU).
+ const: mstr
+ - description:
+ Application AXI-bus Slave interface clock. This is a clock for
+ the CPU-to-PCI memory IO interface.
+ const: slv
+ - description:
+ Controller Core-PCS PIPE interface clock. It's normally
+ supplied by an external PCS-PHY.
+ const: pipe
+ - description:
+ Controller Primary clock. It's assumed that all controller input
+ signals (except resets) are synchronous to this clock.
+ const: core
+ - description:
+ Auxiliary clock for the controller PMC domain. The controller
+ partitioning implies having some parts to operate with this
+ clock in some power management states.
+ const: aux
+ - description:
+ Generic reference clock. In case if there are several
+ interfaces fed up with a common clock source it's advisable to
+ define it with this name (for instance pipe, core and aux can
+ be connected to a single source of the periodic signal).
+ const: ref
+ - description:
+ Clock for the PHY registers interface. Originally this is
+ a PHY-viewport-based interface, but some platform may have
+ specifically designed one.
+ const: phy_reg
+ - description:
+ Vendor-specific clock names. Consider using the generic names
+ above for new bindings.
+ oneOf:
+ - description: See native 'dbi' clock for details
+ enum: [ pcie, pcie_apb_sys, aclk_dbi ]
+ - description: See native 'mstr/slv' clock for details
+ enum: [ pcie_bus, pcie_inbound_axi, pcie_aclk, aclk_mst, aclk_slv ]
+ - description: See native 'pipe' clock for details
+ enum: [ pcie_phy, pcie_phy_ref, link ]
+ - description: See native 'aux' clock for details
+ enum: [ pcie_aux ]
+ - description: See native 'ref' clock for details.
+ enum: [ gio ]
+ - description: See nativs 'phy_reg' clock for details
+ enum: [ pcie_apb_phy, pclk ]
+
+ resets:
+ description:
+ DWC PCIe reference manual explicitly defines a set of the reset
+ signals required to be de-asserted to properly activate the controller
+ sub-parts. All of these signals can be divided into two sub-groups':'
+ application and core resets with respect to the main sub-domains they
+ are supposed to reset. Note the platforms may have some of these signals
+ unspecified in case if they are automatically handled or aggregated into
+ a comprehensive control module.
+ minItems: 1
+ maxItems: 10
+
+ reset-names:
+ minItems: 1
+ maxItems: 10
+ items:
+ oneOf:
+ - description: Data Bus Interface (DBI) domain reset
+ const: dbi
+ - description: AXI-bus Master interface reset
+ const: mstr
+ - description: AXI-bus Slave interface reset
+ const: slv
+ - description: Application-dependent interface reset
+ const: app
+ - description: Controller Non-sticky CSR flags reset
+ const: non-sticky
+ - description: Controller sticky CSR flags reset
+ const: sticky
+ - description: PIPE-interface (Core-PCS) logic reset
+ const: pipe
+ - description:
+ Controller primary reset (resets everything except PMC module)
+ const: core
+ - description: PCS/PHY block reset
+ const: phy
+ - description: PMC hot reset signal
+ const: hot
+ - description: Cold reset signal
+ const: pwr
+ - description:
+ Vendor-specific reset names. Consider using the generic names
+ above for new bindings.
+ oneOf:
+ - description: See native 'app' reset for details
+ enum: [ apps, gio, apb ]
+ - description: See native 'phy' reset for details
+ enum: [ pciephy, link ]
+ - description: See native 'pwr' reset for details
+ enum: [ turnoff ]
+
phys:
description:
There can be up to the number of possible lanes PHYs specified placed in
@@ -180,6 +180,12 @@ examples:
interrupts = <23>, <24>;
interrupt-names = "dma0", "dma1";
+ clocks = <&sys_clk 12>, <&sys_clk 24>;
+ clock-names = "dbi", "ref";
+
+ resets = <&sys_rst 12>, <&sys_rst 24>;
+ reset-names = "dbi", "phy";
+
phys = <&pcie_phy0>, <&pcie_phy1>, <&pcie_phy2>, <&pcie_phy3>;
phy-names = "pcie0", "pcie1", "pcie2", "pcie3";
@@ -195,8 +195,6 @@ properties:
- contains:
const: msi
- clocks: true
-
additionalProperties: true
required: