diff mbox series

[v6,12/12] arm64: dts: qcom: sm8550-mtp: Add PCIe PHYs and controllers nodes

Message ID 20230202123902.3831491-13-abel.vesa@linaro.org (mailing list archive)
State Superseded
Headers show
Series sm8550: Add PCIe HC and PHY support | expand

Commit Message

Abel Vesa Feb. 2, 2023, 12:39 p.m. UTC 
Enable PCIe controllers and PHYs nodes on SM8550 MTP board.

Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---

This patch does not have a v3, but since it is now part of the same
patchset with the controller and the phy drivers patches, I had to
bump the version to 4.

The v5 was here:
https://lore.kernel.org/all/20230124124714.3087948-13-abel.vesa@linaro.org/

Changes since v5:
 * none

Changes since v4:
 * moved here the pinctrl properties and out of dtsi file

Changes since v2:
 * none

Changes since v1:
 * ordered pcie related nodes alphabetically in MTP dts
 * dropped the pipe_mux, phy_pipe and ref clocks from the pcie nodes
 * dropped the child node from the phy nodes, like Johan suggested,
   and updated to use the sc8280xp binding scheme
 * changed "pcie_1_nocsr_com_phy_reset" 2nd reset name of pcie1_phy
   to "nocsr"
 * reordered all pcie nodes properties to look similar to the ones
   from sc8280xp

 arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 38 +++++++++++++++++++++++++
 1 file changed, 38 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index e756f83a941c..265862d0e44f 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -407,6 +407,44 @@  &mdss_mdp {
 	status = "okay";
 };
 
+&pcie_1_phy_aux_clk {
+	clock-frequency = <1000>;
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1e_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	status = "okay";
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3c_0p91>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	vdda-qref-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
 &pm8550_gpios {
 	sdc2_card_det_n: sdc2-card-det-state {
 		pins = "gpio12";