--- ../3.9-rc1-ying_with_MediaCard_reader_disabled_and_nousb/lspci_vvv_with_eSATA_ejected.txt   2013-03-29 14:17:09.000000000 +0100
+++ lspci_vvv_eSATA_ejected.txt 2013-03-29 16:19:31.000000000 +0100
@@ -119,85 +119,85 @@
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
                        Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
                DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
                LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Dell Device 04b3
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
-               Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
+               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: pcieport
 
 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=05, subordinate=06, sec-latency=0
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fff00000-000fffff
        Prefetchable memory behind bridge: 00000000f1100000-00000000f11fffff
-       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
+       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
                        Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet- LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
-               RootSta: PME ReqID 0500, PMEStatus- PMEPending-
+               RootSta: PME ReqID 0000, PMEStatus- PMEPending-
                DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
                LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Dell Device 04b3
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: pcieport
 
@@ -260,51 +260,51 @@
00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) (prog-if 00 [Normal decode])

[cut]
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
                        Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet- LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
                DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
                LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Dell Device 04b3
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
-               Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
+               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: pcieport
 
@@ -385,75 +385,75 @@

 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 06)
        Subsystem: Dell Device 04b3
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 41
        Region 0: I/O ports at e000 [size=256]
        Region 2: Memory at f1104000 (64-bit, prefetchable) [size=4K]
        Region 4: Memory at f1100000 (64-bit, prefetchable) [size=16K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
                Address: 00000000fee0300c  Data: 41a1
        Capabilities: [70] Express (v2) Endpoint, MSI 01
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 4096 bytes
-               DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
+               DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
                        ClockPM+ Surprise- LLActRep- BwNot-
                LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
                LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
                Vector table: BAR=4 offset=00000000
                PBA: BAR=4 offset=00000800
        Capabilities: [d0] Vital Product Data
                Unknown small resource type 00, will not decode more.
        Capabilities: [100 v1] Advanced Error Reporting
-               UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
+               UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
-               AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
+               AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [140 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
        Kernel driver in use: r8169
 

#

The MAbort+ on 1c.1 (handling the rtl8169 eth card) is gone with uninstall of laptop-mode-tools.
with that were maybe associated the errors on the 05:00 devcie itself (the "AERCap")?


Why the following devices do NOT show a difference in PME after laptop-mode-uninstall
I don't know (maybe laptop-mode-tools did NOT fiddle with them):
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5) (prog-if 00 [Normal decode])
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
09:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] (rev 34)
0b:00.0 USB controller: Texas Instruments TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller (rev 02) (prog-if 30 [XHCI])
11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)



So, looks laptop-mode-tools fiddled with 1c.4 XHCI's root port while NOT with EHCI ports, right?
Messing with both 1c.1 and 05:00 (the root port and the eth card) is probably correct, right?
what is 1c.0 don't know. Likely a TPM module (currently enabled in BIOS) or the in BIOS currently
disabled MediaCardReader?




Now, back tot he original problem. Doing 'rmmod sata_sil24' did:

# diff -u -w dmesg_eSATA_ejected.txt dmesg_eSATA_ejected_after_rmmod_sata_sil24.txt
--- dmesg_eSATA_ejected.txt     2013-03-29 16:19:22.000000000 +0100
+++ dmesg_eSATA_ejected_after_rmmod_sata_sil24.txt      2013-03-29 16:21:09.000000000 +0100
@@ -815,3 +815,4 @@
 [   36.552799] perf_event_intel: PEBS enabled due to microcode update
 [   39.075539] r8169 0000:05:00.0 eth0: link down
 [   45.523586] r8169 0000:05:00.0 eth0: link up
+[  276.940568] sata_sil24: IRQ status == 0xffffffff, PCI fault or device removal?
#

So, good, the PME# flipping back and forth doe snoty happen, likely a laptop-mode-tools
caused that before.


# diff -u -w lspci_vvv_eSATA_ejected.txt lspci_vvv_eSATA_ejected_after_rmmod_sata_sil24.txt
--- lspci_vvv_eSATA_ejected.txt 2013-03-29 16:19:31.000000000 +0100
+++ lspci_vvv_eSATA_ejected_after_rmmod_sata_sil24.txt  2013-03-29 16:21:00.000000000 +0100
@@ -523,5 +523,4 @@
 
 11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev ff) (prog-if ff)
        !!! Unknown header type 7f
-       Kernel driver in use: sata_sil24
 
#


If we think of the situation with laptop-mode-tools installed and the rmmod, this
would have happened (note the 00:1c.7) lines:

# diff -u -w ../3.9-rc1-ying_with_MediaCard_reader_disabled_and_nousb/lspci_vvv_with_eSATA_ejected.txt ../3.9-rc1-ying_with_MediaCard_reader_disabled_and_nousb/lspci_vvv_with_eSATA_ejected_and_rmmod_sata_sil24.txt 
--- ../3.9-rc1-ying_with_MediaCard_reader_disabled_and_nousb/lspci_vvv_with_eSATA_ejected.txt   2013-03-29 14:17:09.000000000 +0100
+++ ../3.9-rc1-ying_with_MediaCard_reader_disabled_and_nousb/lspci_vvv_with_eSATA_ejected_and_rmmod_sata_sil24.txt      2013-03-29 14:19:18.000000000 +0100
@@ -329,7 +329,7 @@
        Capabilities: [90] Subsystem: Dell Device 04b3
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
-               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
+               Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
        Kernel driver in use: pcieport
 
 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
@@ -523,5 +523,4 @@
 
 11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev ff) (prog-if ff)
        !!! Unknown header type 7f
-       Kernel driver in use: sata_sil24
 
#

In both cases, the issue with PME# flipping back and forth is gone

Still talking about the rmmod sata-sil24, it does cause release of the memmory
(did not check /proc/iomem this today while tetsing your patch and laptop-mode-tools were
still instaleld):

# diff -u -w iomem_eSATA_ejected.txt iomem_eSATA_ejected_after_rmmod_sata_sil24.txt
--- iomem_eSATA_ejected.txt     2013-03-29 16:19:15.000000000 +0100
+++ iomem_eSATA_ejected_after_rmmod_sata_sil24.txt      2013-03-29 16:21:18.000000000 +0100
@@ -44,9 +44,7 @@
   f6c00000-f7cfffff : PCI Bus 0000:11
     f6c00000-f6c7ffff : 0000:11:00.0
     f6c80000-f6c83fff : 0000:11:00.0
-      f6c80000-f6c83fff : sata_sil24
     f6c84000-f6c8407f : 0000:11:00.0
-      f6c84000-f6c8407f : sata_sil24
   f7d00000-f7dfffff : PCI Bus 0000:0b
     f7d00000-f7d0ffff : 0000:0b:00.0
     f7d10000-f7d11fff : 0000:0b:00.0
#


Like in previous tests the IRQ19 is released during rmmod:
 # diff -u -w interrupts_eSATA_ejected.txt interrupts_eSATA_ejected_after_rmmod_sata_sil24.txt 
--- interrupts_eSATA_ejected.txt        2013-03-29 16:19:05.000000000 +0100
+++ interrupts_eSATA_ejected_after_rmmod_sata_sil24.txt 2013-03-29 16:21:27.000000000 +0100
@@ -1,27 +1,26 @@
            CPU0       CPU1       
   0:         24          0   IO-APIC-edge      timer
-  1:       1366          0   IO-APIC-edge      i8042
+  1:       2524          0   IO-APIC-edge      i8042
   8:         56          0   IO-APIC-edge      rtc0
   9:          1          0   IO-APIC-fasteoi   acpi
- 12:        256          0   IO-APIC-edge      i8042
- 19:          0          0   IO-APIC-fasteoi   sata_sil24
- 40:       3830          0   PCI-MSI-edge      ahci
- 41:        421          0   PCI-MSI-edge      eth0
+ 12:        466          0   IO-APIC-edge      i8042
+ 40:       3996          0   PCI-MSI-edge      ahci
+ 41:        594          0   PCI-MSI-edge      eth0
  42:        948          0   PCI-MSI-edge      snd_hda_intel
  43:          1          0   PCI-MSI-edge      iwlwifi
  44:        201          0   PCI-MSI-edge      i915





Finally, a hotinsert of the eSATA card now does:

# diff -u -w lspci_vvv_eSATA_ejected_after_rmmod_sata_sil24.txt lspci_vvv_eSATA_ejected_after_rmmod_sata_sil24_and_hotinsert.txt
--- lspci_vvv_eSATA_ejected_after_rmmod_sata_sil24.txt  2013-03-29 16:21:00.000000000 +0100
+++ lspci_vvv_eSATA_ejected_after_rmmod_sata_sil24_and_hotinsert.txt    2013-03-29 16:23:40.000000000 +0100
@@ -307,12 +307,12 @@
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
-               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
+               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
