@@ -16,10 +16,7 @@ obj-$(CONFIG_PINCTRL) += pinctrl/
obj-$(CONFIG_GPIOLIB) += gpio/
obj-y += pwm/
-obj-$(CONFIG_PCI) += pci/
-obj-$(CONFIG_PCI_ENDPOINT) += pci/endpoint/
-# PCI dwc controller drivers
-obj-y += pci/dwc/
+obj-y += pci/
obj-$(CONFIG_PARISC) += parisc/
obj-$(CONFIG_RAPIDIO) += rapidio/
@@ -125,6 +125,7 @@ config PCI_PASID
config PCI_LABEL
def_bool y if (DMI || ACPI)
+ depends on PCI
select NLS
config PCI_HYPERV
@@ -3,12 +3,15 @@
# Makefile for the PCI bus specific drivers.
#
-obj-y += access.o bus.o probe.o host-bridge.o remove.o pci.o \
+obj-$(CONFIG_PCI) += access.o bus.o probe.o host-bridge.o remove.o pci.o \
pci-driver.o search.o pci-sysfs.o rom.o setup-res.o \
irq.o vpd.o setup-bus.o vc.o mmap.o setup-irq.o
+ifdef CONFIG_PCI
obj-$(CONFIG_PROC_FS) += proc.o
obj-$(CONFIG_SYSFS) += slot.o
+obj-$(CONFIG_OF) += of.o
+endif
obj-$(CONFIG_PCI_QUIRKS) += quirks.o
@@ -44,10 +47,14 @@ obj-$(CONFIG_PCI_ECAM) += ecam.o
obj-$(CONFIG_XEN_PCIDEV_FRONTEND) += xen-pcifront.o
-obj-$(CONFIG_OF) += of.o
-
ccflags-$(CONFIG_PCI_DEBUG) := -DDEBUG
# PCI host controller drivers
obj-y += host/
obj-y += switch/
+
+obj-$(CONFIG_PCI_ENDPOINT) += endpoint/
+
+# Endpoint library must be initialized before its users
+# pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW
+obj-y += dwc/
@@ -25,4 +25,6 @@ obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
# ARM64 and use internal ifdefs to only build the pieces we need
# depending on whether ACPI, the DT driver, or both are enabled.
+ifdef CONFIG_PCI
obj-$(CONFIG_ARM64) += pcie-hisi.o
+endif
@@ -34,6 +34,8 @@ obj-$(CONFIG_VMD) += vmd.o
# ARM64 and use internal ifdefs to only build the pieces we need
# depending on whether ACPI, the DT driver, or both are enabled.
+ifdef CONFIG_PCI
obj-$(CONFIG_ARM64) += pci-thunder-ecam.o
obj-$(CONFIG_ARM64) += pci-thunder-pem.o
obj-$(CONFIG_ARM64) += pci-xgene.o
+endif
Clean up drivers/Makefile by moving the pci/endpoint and pci/dwc entries from drivers/Makefile into drivers/pci/Makefile. Since we don't want to introduce any dependency between CONFIG_PCI and CONFIG_PCI_ENDPOINT, we now always execute drivers/pci/Makefile. Hence all Makefiles in drivers/pci/ were updated accordingly so no file is compiled when CONFIG_PCI is not defined. Also, we add a comment to reinforce that EPC and EPF libraries must be initialized before their users. Hence built-in EPC drivers, such as those of Designware, are linked after the endpoint core libraries. Finally, we add another comment to explain why obj-y has been chosen instead of obj-$(CONFIG_PCIE_DW) to parse the dwc/ sub-folder. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com> --- drivers/Makefile | 5 +---- drivers/pci/Kconfig | 1 + drivers/pci/Makefile | 13 ++++++++++--- drivers/pci/dwc/Makefile | 2 ++ drivers/pci/host/Makefile | 2 ++ 5 files changed, 16 insertions(+), 7 deletions(-)