| Message ID | 20210621072424.111733-5-jagan@amarulasolutions.com |
|---|---|
| State | RFC |
| Headers | show |
| Series | arm64: imx8mm: Add MIPI DSI support | expand |
On 21/06/2021 09:24, Jagan Teki wrote: > Samsung SEC MIPI DSIM DPHY controller is part of registers > available in SEC MIPI DSIM bridge for NXP's i.MX8M Mini and > Nano Processors. > > Add phy driver for it. > > Cc: Kishon Vijay Abraham I <kishon@ti.com> > Cc: Vinod Koul <vkoul@kernel.org> > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > --- > drivers/phy/samsung/Kconfig | 9 + > drivers/phy/samsung/Makefile | 1 + > drivers/phy/samsung/phy-sec-dsim-dphy.c | 236 ++++++++++++++++++++++++ > 3 files changed, 246 insertions(+) > create mode 100644 drivers/phy/samsung/phy-sec-dsim-dphy.c You add a driver for a Samsung's component, so please Cc respective folks. They might help you with it or provide comments to avoid duplication of drivers/code: Around phy: Marek Szyprowski <m.szyprowski@samsung.com> Jaehoon Chung <jh80.chung@samsung.com> Around MIPI/DRM: Inki Dae <inki.dae@samsung.com> Seung-Woo Kim <sw0312.kim@samsung.com> Andrzej Hajda <a.hajda@samsung.com> and: linux-samsung-soc@vger.kernel.org > > diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig > index e20d2fcc9fe7..e80d40d1278c 100644 > --- a/drivers/phy/samsung/Kconfig > +++ b/drivers/phy/samsung/Kconfig > @@ -103,3 +103,12 @@ config PHY_EXYNOS5250_SATA > Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s, > SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host > port to accept one SATA device. > + > +config PHY_SEC_DSIM_DPHY SEC is not a codename of a project/product/silicon. It is a company name, so basically you called this "PHY_SAMSUNG_DSIM_DPHY" which is too generic. > + tristate "Samsung SEC MIPI DSIM DPHY driver" What is Samsung SEC? Either Samsung or SEC, not both. > + depends on OF && HAS_IOMEM > + select GENERIC_PHY > + select REGMAP_MMIO > + help > + Enable this to add support for the SEC MIPI DSIM DPHY as found > + on NXP's i.MX8M Mini and Nano family of SOCs. > diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile > index 3959100fe8a2..4d46c7ec0072 100644 > --- a/drivers/phy/samsung/Makefile > +++ b/drivers/phy/samsung/Makefile > @@ -11,3 +11,4 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o > phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) += phy-s5pv210-usb2.o > obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o > obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o > +obj-$(CONFIG_PHY_SEC_DSIM_DPHY) += phy-sec-dsim-dphy.o > diff --git a/drivers/phy/samsung/phy-sec-dsim-dphy.c b/drivers/phy/samsung/phy-sec-dsim-dphy.c > new file mode 100644 > index 000000000000..31de4a774b5f > --- /dev/null > +++ b/drivers/phy/samsung/phy-sec-dsim-dphy.c > @@ -0,0 +1,236 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright (C) 2018 NXP > + * Copyright (C) 2021 Amarula Solutions(India) > + */ > + > +#include <linux/clk.h> > +#include <linux/clk-provider.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_platform.h> > +#include <linux/phy/phy.h> > +#include <linux/regmap.h> > + > +#define DSI_PHYCTRL_B1 0x00 > +#define DSI_PHYCTRL_B2 0x04 > +#define DSI_PHYCTRL_M1 0x08 > +#define DSI_PHYCTRL_M2 0x0c > +#define DSI_PHYTIMING 0x10 > +#define DSI_PHYTIMING1 0x14 > +#define DSI_PHYTIMING2 0x18 > + > +/* phytiming */ > +#define M_TLPXCTL_MASK GENMASK(15, 8) What is the "M_" prefix for? > +#define M_TLPXCTL(x) FIELD_PREP(M_TLPXCTL_MASK, (x)) > +#define M_THSEXITCTL_MASK GENMASK(7, 0) > +#define M_THSEXITCTL(x) FIELD_PREP(M_THSEXITCTL_MASK, (x)) > + > +/* phytiming1 */ > +#define M_TCLKPRPRCTL_MASK GENMASK(31, 24) > +#define M_TCLKPRPRCTL(x) FIELD_PREP(M_TCLKPRPRCTL_MASK, (x)) > +#define M_TCLKZEROCTL_MASK GENMASK(23, 16) > +#define M_TCLKZEROCTL(x) FIELD_PREP(M_TCLKZEROCTL_MASK, (x)) > +#define M_TCLKPOSTCTL_MASK GENMASK(15, 8) > +#define M_TCLKPOSTCTL(x) FIELD_PREP(M_TCLKPOSTCTL_MASK, (x)) > +#define M_TCLKTRAILCTL_MASK GENMASK(7, 0) > +#define M_TCLKTRAILCTL(x) FIELD_PREP(M_TCLKTRAILCTL_MASK, (x)) > + > +/* phytiming2 */ > +#define M_THSPRPRCTL_MASK GENMASK(23, 16) > +#define M_THSPRPRCTL(x) FIELD_PREP(M_THSPRPRCTL_MASK, (x)) > +#define M_THSZEROCTL_MASK GENMASK(15, 8) > +#define M_THSZEROCTL(x) FIELD_PREP(M_THSZEROCTL_MASK, (x)) > +#define M_THSTRAILCTL_MASK GENMASK(7, 0) > +#define M_THSTRAILCTL(x) FIELD_PREP(M_THSTRAILCTL_MASK, (x)) > + > +struct dsim_dphy_plat_data { Remove the m_ prefix. Please document all fields. > + unsigned int m_tlpxctl; > + unsigned int m_thsexitctl; > + unsigned int m_tclkprprctl; > + unsigned int m_tclkzeroctl; > + unsigned int m_tclkpostctl; > + unsigned int m_tclktrailctl; > + unsigned int m_thsprprctl; > + unsigned int m_thszeroctl; > + unsigned int m_thstrailctl; > +}; > + > +struct dsim_dphy { > + struct regmap *regmap; > + struct clk *phy_ref_clk; > + const struct dsim_dphy_plat_data *pdata; > +}; > + > +static const struct regmap_config dsim_dphy_regmap_config = { > + .reg_bits = 8, > + .val_bits = 32, > + .reg_stride = 4, > + .max_register = DSI_PHYTIMING2, > + .name = "mipi-dphy", > +}; > + > +static int dsim_dphy_init(struct phy *phy) > +{ > + struct dsim_dphy *dphy = phy_get_drvdata(phy); > + const struct dsim_dphy_plat_data *pdata = dphy->pdata; > + u32 reg; > + > + /* phytiming */ > + regmap_read(dphy->regmap, DSI_PHYTIMING, ®); > + > + reg &= ~M_TLPXCTL_MASK; > + reg |= M_TLPXCTL(pdata->m_tlpxctl); > + reg &= ~M_THSEXITCTL_MASK; > + reg |= M_THSEXITCTL(pdata->m_thsexitctl); > + regmap_write(dphy->regmap, DSI_PHYTIMING, reg); > + > + /* phytiming1 */ > + regmap_read(dphy->regmap, DSI_PHYTIMING1, ®); > + > + reg &= ~M_TCLKPRPRCTL_MASK; > + reg |= M_TCLKPRPRCTL(pdata->m_tclkprprctl); > + reg &= ~M_TCLKZEROCTL_MASK; > + reg |= M_TCLKZEROCTL(pdata->m_tclkzeroctl); > + reg &= ~M_TCLKPOSTCTL_MASK; > + reg |= M_TCLKPOSTCTL(pdata->m_tclkpostctl); > + reg &= ~M_TCLKTRAILCTL_MASK; > + reg |= M_TCLKTRAILCTL(pdata->m_tclktrailctl); > + regmap_write(dphy->regmap, DSI_PHYTIMING1, reg); > + > + /* phytiming2 */ > + regmap_read(dphy->regmap, DSI_PHYTIMING2, ®); > + > + reg &= ~M_THSPRPRCTL_MASK; > + reg |= M_THSPRPRCTL(pdata->m_thsprprctl); > + reg &= ~M_THSZEROCTL_MASK; > + reg |= M_THSZEROCTL(pdata->m_thszeroctl); > + reg &= ~M_THSTRAILCTL_MASK; > + reg |= M_THSTRAILCTL(pdata->m_thstrailctl); > + regmap_write(dphy->regmap, DSI_PHYTIMING2, reg); > + > + return 0; > +} > + > +static int dsim_dphy_exit(struct phy *phy) > +{ > + return 0; > +} > + > +static int dsim_dphy_power_on(struct phy *phy) > +{ > + struct dsim_dphy *dphy = phy_get_drvdata(phy); > + int ret; > + > + ret = clk_prepare_enable(dphy->phy_ref_clk); > + if (ret < 0) > + return ret; > + > + return ret; > +} > + > +static int dsim_dphy_power_off(struct phy *phy) > +{ > + struct dsim_dphy *dphy = phy_get_drvdata(phy); > + > + clk_disable_unprepare(dphy->phy_ref_clk); > + > + return 0; > +} > + > +static const struct phy_ops dsim_dphy_phy_ops = { > + .init = dsim_dphy_init, > + .exit = dsim_dphy_exit, > + .power_on = dsim_dphy_power_on, > + .power_off = dsim_dphy_power_off, > + .owner = THIS_MODULE, > +}; > + > +static const struct dsim_dphy_plat_data imx8mm_dphy_plat_data = { > + /* phytiming */ > + .m_tlpxctl = 0x06, > + .m_thsexitctl = 0x0b, > + /* phytiming1 */ > + .m_tclkprprctl = 0x07, > + .m_tclkzeroctl = 0x26, > + .m_tclkpostctl = 0x0d, > + .m_tclktrailctl = 0x08, > + /* phytimings2 */ > + .m_thsprprctl = 0x08, > + .m_thszeroctl = 0x0d, > + .m_thstrailctl = 0x0b, > +}; > + > +static const struct of_device_id dsim_dphy_of_match[] = { > + { > + .compatible = "fsl,imx8mm-sec-dsim-dphy", > + .data = &imx8mm_dphy_plat_data, > + }, > + { /* sentinel */ }, > +}; > +MODULE_DEVICE_TABLE(of, dsim_dphy_of_match); > + > +static int dsim_dphy_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct device_node *np = dev->of_node; > + struct phy_provider *phy_provider; > + struct dsim_dphy *dphy; > + struct phy *phy; > + void __iomem *base; > + > + if (!np) > + return -ENODEV; How can this driver bind without 'np'? How is it possible? > + > + dphy = devm_kzalloc(dev, sizeof(*dphy), GFP_KERNEL); > + if (!dphy) > + return -ENOMEM; > + > + dphy->pdata = of_device_get_match_data(&pdev->dev); > + if (!dphy->pdata) > + return -EINVAL; > + > + base = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(base)) > + return PTR_ERR(base); > + > + dphy->regmap = devm_regmap_init_mmio(&pdev->dev, base, > + &dsim_dphy_regmap_config); > + if (IS_ERR(dphy->regmap)) { > + dev_err(dev, "failed create the DPHY regmap\n"); > + return PTR_ERR(dphy->regmap); > + } > + > + dphy->phy_ref_clk = devm_clk_get(&pdev->dev, "phy_ref"); > + if (IS_ERR(dphy->phy_ref_clk)) { > + dev_err(dev, "failed to get phy_ref clock\n"); > + return PTR_ERR(dphy->phy_ref_clk); > + } > + > + dev_set_drvdata(dev, dphy); > + > + phy = devm_phy_create(dev, np, &dsim_dphy_phy_ops); > + if (IS_ERR(phy)) { > + dev_err(dev, "failed to create phy %ld\n", PTR_ERR(phy)); > + return PTR_ERR(phy); > + } > + phy_set_drvdata(phy, dphy); > + > + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); > + > + return PTR_ERR_OR_ZERO(phy_provider); > +} > + > +static struct platform_driver dsim_dphy_driver = { > + .probe = dsim_dphy_probe, > + .driver = { > + .name = "sec-dsim-dphy", "sec" it's too generic, what if next time we have another one from Samsung? sec2? Please choose a name matching the actual component. > + .of_match_table = dsim_dphy_of_match, > + } > +}; > +module_platform_driver(dsim_dphy_driver); > + > +MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>"); > +MODULE_DESCRIPTION("Samsung SEC MIPI DSIM DPHY driver");> +MODULE_LICENSE("GPL"); > Best regards, Krzysztof
diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig index e20d2fcc9fe7..e80d40d1278c 100644 --- a/drivers/phy/samsung/Kconfig +++ b/drivers/phy/samsung/Kconfig @@ -103,3 +103,12 @@ config PHY_EXYNOS5250_SATA Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s, SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host port to accept one SATA device. + +config PHY_SEC_DSIM_DPHY + tristate "Samsung SEC MIPI DSIM DPHY driver" + depends on OF && HAS_IOMEM + select GENERIC_PHY + select REGMAP_MMIO + help + Enable this to add support for the SEC MIPI DSIM DPHY as found + on NXP's i.MX8M Mini and Nano family of SOCs. diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile index 3959100fe8a2..4d46c7ec0072 100644 --- a/drivers/phy/samsung/Makefile +++ b/drivers/phy/samsung/Makefile @@ -11,3 +11,4 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) += phy-s5pv210-usb2.o obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o +obj-$(CONFIG_PHY_SEC_DSIM_DPHY) += phy-sec-dsim-dphy.o diff --git a/drivers/phy/samsung/phy-sec-dsim-dphy.c b/drivers/phy/samsung/phy-sec-dsim-dphy.c new file mode 100644 index 000000000000..31de4a774b5f --- /dev/null +++ b/drivers/phy/samsung/phy-sec-dsim-dphy.c @@ -0,0 +1,236 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 NXP + * Copyright (C) 2021 Amarula Solutions(India) + */ + +#include <linux/clk.h> +#include <linux/clk-provider.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/phy/phy.h> +#include <linux/regmap.h> + +#define DSI_PHYCTRL_B1 0x00 +#define DSI_PHYCTRL_B2 0x04 +#define DSI_PHYCTRL_M1 0x08 +#define DSI_PHYCTRL_M2 0x0c +#define DSI_PHYTIMING 0x10 +#define DSI_PHYTIMING1 0x14 +#define DSI_PHYTIMING2 0x18 + +/* phytiming */ +#define M_TLPXCTL_MASK GENMASK(15, 8) +#define M_TLPXCTL(x) FIELD_PREP(M_TLPXCTL_MASK, (x)) +#define M_THSEXITCTL_MASK GENMASK(7, 0) +#define M_THSEXITCTL(x) FIELD_PREP(M_THSEXITCTL_MASK, (x)) + +/* phytiming1 */ +#define M_TCLKPRPRCTL_MASK GENMASK(31, 24) +#define M_TCLKPRPRCTL(x) FIELD_PREP(M_TCLKPRPRCTL_MASK, (x)) +#define M_TCLKZEROCTL_MASK GENMASK(23, 16) +#define M_TCLKZEROCTL(x) FIELD_PREP(M_TCLKZEROCTL_MASK, (x)) +#define M_TCLKPOSTCTL_MASK GENMASK(15, 8) +#define M_TCLKPOSTCTL(x) FIELD_PREP(M_TCLKPOSTCTL_MASK, (x)) +#define M_TCLKTRAILCTL_MASK GENMASK(7, 0) +#define M_TCLKTRAILCTL(x) FIELD_PREP(M_TCLKTRAILCTL_MASK, (x)) + +/* phytiming2 */ +#define M_THSPRPRCTL_MASK GENMASK(23, 16) +#define M_THSPRPRCTL(x) FIELD_PREP(M_THSPRPRCTL_MASK, (x)) +#define M_THSZEROCTL_MASK GENMASK(15, 8) +#define M_THSZEROCTL(x) FIELD_PREP(M_THSZEROCTL_MASK, (x)) +#define M_THSTRAILCTL_MASK GENMASK(7, 0) +#define M_THSTRAILCTL(x) FIELD_PREP(M_THSTRAILCTL_MASK, (x)) + +struct dsim_dphy_plat_data { + unsigned int m_tlpxctl; + unsigned int m_thsexitctl; + unsigned int m_tclkprprctl; + unsigned int m_tclkzeroctl; + unsigned int m_tclkpostctl; + unsigned int m_tclktrailctl; + unsigned int m_thsprprctl; + unsigned int m_thszeroctl; + unsigned int m_thstrailctl; +}; + +struct dsim_dphy { + struct regmap *regmap; + struct clk *phy_ref_clk; + const struct dsim_dphy_plat_data *pdata; +}; + +static const struct regmap_config dsim_dphy_regmap_config = { + .reg_bits = 8, + .val_bits = 32, + .reg_stride = 4, + .max_register = DSI_PHYTIMING2, + .name = "mipi-dphy", +}; + +static int dsim_dphy_init(struct phy *phy) +{ + struct dsim_dphy *dphy = phy_get_drvdata(phy); + const struct dsim_dphy_plat_data *pdata = dphy->pdata; + u32 reg; + + /* phytiming */ + regmap_read(dphy->regmap, DSI_PHYTIMING, ®); + + reg &= ~M_TLPXCTL_MASK; + reg |= M_TLPXCTL(pdata->m_tlpxctl); + reg &= ~M_THSEXITCTL_MASK; + reg |= M_THSEXITCTL(pdata->m_thsexitctl); + regmap_write(dphy->regmap, DSI_PHYTIMING, reg); + + /* phytiming1 */ + regmap_read(dphy->regmap, DSI_PHYTIMING1, ®); + + reg &= ~M_TCLKPRPRCTL_MASK; + reg |= M_TCLKPRPRCTL(pdata->m_tclkprprctl); + reg &= ~M_TCLKZEROCTL_MASK; + reg |= M_TCLKZEROCTL(pdata->m_tclkzeroctl); + reg &= ~M_TCLKPOSTCTL_MASK; + reg |= M_TCLKPOSTCTL(pdata->m_tclkpostctl); + reg &= ~M_TCLKTRAILCTL_MASK; + reg |= M_TCLKTRAILCTL(pdata->m_tclktrailctl); + regmap_write(dphy->regmap, DSI_PHYTIMING1, reg); + + /* phytiming2 */ + regmap_read(dphy->regmap, DSI_PHYTIMING2, ®); + + reg &= ~M_THSPRPRCTL_MASK; + reg |= M_THSPRPRCTL(pdata->m_thsprprctl); + reg &= ~M_THSZEROCTL_MASK; + reg |= M_THSZEROCTL(pdata->m_thszeroctl); + reg &= ~M_THSTRAILCTL_MASK; + reg |= M_THSTRAILCTL(pdata->m_thstrailctl); + regmap_write(dphy->regmap, DSI_PHYTIMING2, reg); + + return 0; +} + +static int dsim_dphy_exit(struct phy *phy) +{ + return 0; +} + +static int dsim_dphy_power_on(struct phy *phy) +{ + struct dsim_dphy *dphy = phy_get_drvdata(phy); + int ret; + + ret = clk_prepare_enable(dphy->phy_ref_clk); + if (ret < 0) + return ret; + + return ret; +} + +static int dsim_dphy_power_off(struct phy *phy) +{ + struct dsim_dphy *dphy = phy_get_drvdata(phy); + + clk_disable_unprepare(dphy->phy_ref_clk); + + return 0; +} + +static const struct phy_ops dsim_dphy_phy_ops = { + .init = dsim_dphy_init, + .exit = dsim_dphy_exit, + .power_on = dsim_dphy_power_on, + .power_off = dsim_dphy_power_off, + .owner = THIS_MODULE, +}; + +static const struct dsim_dphy_plat_data imx8mm_dphy_plat_data = { + /* phytiming */ + .m_tlpxctl = 0x06, + .m_thsexitctl = 0x0b, + /* phytiming1 */ + .m_tclkprprctl = 0x07, + .m_tclkzeroctl = 0x26, + .m_tclkpostctl = 0x0d, + .m_tclktrailctl = 0x08, + /* phytimings2 */ + .m_thsprprctl = 0x08, + .m_thszeroctl = 0x0d, + .m_thstrailctl = 0x0b, +}; + +static const struct of_device_id dsim_dphy_of_match[] = { + { + .compatible = "fsl,imx8mm-sec-dsim-dphy", + .data = &imx8mm_dphy_plat_data, + }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, dsim_dphy_of_match); + +static int dsim_dphy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct phy_provider *phy_provider; + struct dsim_dphy *dphy; + struct phy *phy; + void __iomem *base; + + if (!np) + return -ENODEV; + + dphy = devm_kzalloc(dev, sizeof(*dphy), GFP_KERNEL); + if (!dphy) + return -ENOMEM; + + dphy->pdata = of_device_get_match_data(&pdev->dev); + if (!dphy->pdata) + return -EINVAL; + + base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(base)) + return PTR_ERR(base); + + dphy->regmap = devm_regmap_init_mmio(&pdev->dev, base, + &dsim_dphy_regmap_config); + if (IS_ERR(dphy->regmap)) { + dev_err(dev, "failed create the DPHY regmap\n"); + return PTR_ERR(dphy->regmap); + } + + dphy->phy_ref_clk = devm_clk_get(&pdev->dev, "phy_ref"); + if (IS_ERR(dphy->phy_ref_clk)) { + dev_err(dev, "failed to get phy_ref clock\n"); + return PTR_ERR(dphy->phy_ref_clk); + } + + dev_set_drvdata(dev, dphy); + + phy = devm_phy_create(dev, np, &dsim_dphy_phy_ops); + if (IS_ERR(phy)) { + dev_err(dev, "failed to create phy %ld\n", PTR_ERR(phy)); + return PTR_ERR(phy); + } + phy_set_drvdata(phy, dphy); + + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + + return PTR_ERR_OR_ZERO(phy_provider); +} + +static struct platform_driver dsim_dphy_driver = { + .probe = dsim_dphy_probe, + .driver = { + .name = "sec-dsim-dphy", + .of_match_table = dsim_dphy_of_match, + } +}; +module_platform_driver(dsim_dphy_driver); + +MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>"); +MODULE_DESCRIPTION("Samsung SEC MIPI DSIM DPHY driver"); +MODULE_LICENSE("GPL");
Samsung SEC MIPI DSIM DPHY controller is part of registers available in SEC MIPI DSIM bridge for NXP's i.MX8M Mini and Nano Processors. Add phy driver for it. Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- drivers/phy/samsung/Kconfig | 9 + drivers/phy/samsung/Makefile | 1 + drivers/phy/samsung/phy-sec-dsim-dphy.c | 236 ++++++++++++++++++++++++ 3 files changed, 246 insertions(+) create mode 100644 drivers/phy/samsung/phy-sec-dsim-dphy.c