@@ -9,6 +9,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
#include "rk3588.dtsi"
/ {
@@ -224,6 +225,18 @@ vcc5v0_usb: vcc5v0-usb-regulator {
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc5v0_usbdcin>;
};
+
+ vbus5v0_typec: vbus5v0-typec {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus5v0_typec";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio4 RK_PD0 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&vcc5v0_usb>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&typec5v_pwren>;
+ };
};
&combphy0_ps {
@@ -284,6 +297,56 @@ &gmac0_rgmii_clk
&i2c2 {
status = "okay";
+ usbc0: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vbus5v0_typec>;
+ status = "okay";
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ power-role = "dual";
+ try-power-role = "source";
+ op-sink-microwatt = <1000000>;
+ sink-pdos =
+ <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc0_orien_sw: endpoint {
+ remote-endpoint = <&usbdp_phy0_orientation_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc0_role_sw: endpoint {
+ remote-endpoint = <&dwc3_0_role_switch>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ dp_altmode_mux: endpoint {
+ remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+ };
+ };
+ };
+ };
+ };
+
hym8563: rtc@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
@@ -410,6 +473,16 @@ vcc5v0_host_en: vcc5v0-host-en {
rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
+
+ usb-typec {
+ usbc0_int: usbc0-int {
+ rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ typec5v_pwren: typec5v-pwren {
+ rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
};
&pwm2 {
@@ -1040,6 +1113,22 @@ &sata0 {
status = "okay";
};
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ status = "okay";
+};
+
&u2phy2 {
status = "okay";
};
@@ -1078,3 +1167,65 @@ &usb_host1_ehci {
&usb_host1_ohci {
status = "okay";
};
+
+&usbdp_phy0 {
+ orientation-switch;
+ mode-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_orientation_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_orien_sw>;
+ };
+
+ usbdp_phy0_dp_altmode_mux: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dp_altmode_mux>;
+ };
+ };
+};
+
+&usbdp_phy0_u3 {
+ status = "okay";
+};
+
+&usbdp_phy1 {
+ /*
+ * USBDP PHY1 is wired to a female USB3 Type-A connector. Additionally
+ * the differential pairs 2+3 and the aux channel are wired to a RTD2166,
+ * which converts the DP signal into VGA. This is exposed on the
+ * board via a female VGA connector.
+ */
+ rockchip,dp-lane-mux = <2 3>;
+ status = "okay";
+};
+
+&usbdp_phy1_u3 {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dwc3_0_role_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_role_sw>;
+ };
+ };
+};
+
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
Add support for the board's USB3 connectors. It has 1x USB Type-A and 1x USB Type-C. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> --- .../boot/dts/rockchip/rk3588-evb1-v10.dts | 151 ++++++++++++++++++ 1 file changed, 151 insertions(+)