new file mode 100644
@@ -0,0 +1,44 @@
+* ST-Ericsson DB8500 Thermal
+
+** Thermal node properties:
+
+- compatible : "stericsson,db8500-thermal";
+- reg : address range of the thermal sensor registers;
+- interrupts : interrupts generated from PRCMU;
+- interrupt-names : "IRQ_HOTMON_LOW" and "IRQ_HOTMON_HIGH";
+- num-trips : number of total trip points, this is required, set it 0 if none,
+ if greater than 0, the following properties must be defined;
+- tripN-temp : temperature of trip point N, should be in ascending order;
+- tripN-type : type of trip point N, should be one of "active" "passive" "hot"
+ "critical";
+- tripN-cdev-num : number of the cooling devices which can be bound to trip
+ point N, this is required if trip point N is defined, set it 0 if none,
+ otherwise the following cooling device names must be defined;
+- tripN-cdev-nameM : name of the No. M cooling device of trip point N;
+
+Usually the num-trips and tripN-*** are separated in board related dts files.
+
+Example:
+thermal@801573c0 {
+ compatible = "stericsson,db8500-thermal";
+ reg = <0x801573c0 0x40>;
+ interrupts = <21 0x4>, <22 0x4>;
+ interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH";
+
+ num-trips = <3>;
+
+ trip0-temp = <75000>;
+ trip0-type = "active";
+ trip0-cdev-num = <1>;
+ trip0-cdev-name0 = "thermal-cpufreq-0";
+
+ trip1-temp = <80000>;
+ trip1-type = "active";
+ trip1-cdev-num = <2>;
+ trip1-cdev-name0 = "thermal-cpufreq-0";
+ trip1-cdev-name1 = "thermal-fan";
+
+ trip2-temp = <85000>;
+ trip2-type = "critical";
+ trip2-cdev-num = <0>;
+}
@@ -31,6 +31,26 @@ config CPU_THERMAL
and not the ACPI interface.
If you want this support, you should say Y here.
+config DB8500_THERMAL
+ bool "DB8500 thermal management"
+ depends on THERMAL
+ default y
+ help
+ Adds DB8500 thermal management implementation according to the thermal
+ management framework. A thermal zone with several trip points will be
+ created. Cooling devices can be bound to the trip points to cool this
+ thermal zone if trip points reached.
+
+config DB8500_CPUFREQ_COOLING
+ tristate "DB8500 cpufreq cooling"
+ depends on CPU_THERMAL
+ default y
+ help
+ Adds DB8500 cpufreq cooling devices, and these cooling devices can be
+ bound to thermal zone trip points. When a trip point reached, the
+ bound cpufreq cooling device turns active to set CPU frequency low to
+ cool down the CPU.
+
config SPEAR_THERMAL
bool "SPEAr thermal sensor driver"
depends on THERMAL
@@ -7,3 +7,5 @@ obj-$(CONFIG_CPU_THERMAL) += cpu_cooling.o
obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
obj-$(CONFIG_EXYNOS_THERMAL) += exynos_thermal.o
+obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o
+obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o
new file mode 100644
@@ -0,0 +1,108 @@
+/*
+ * db8500_cpufreq_cooling.c - DB8500 cpufreq works as cooling device.
+ *
+ * Copyright (C) 2012 ST-Ericsson
+ * Copyright (C) 2012 Linaro Ltd.
+ *
+ * Author: Hongbo Zhang <hongbo.zhang@linaro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/cpu_cooling.h>
+#include <linux/cpufreq.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+static int db8500_cpufreq_cooling_probe(struct platform_device *pdev)
+{
+ struct thermal_cooling_device *cdev;
+ struct cpumask mask_val;
+
+ /* make sure cpufreq driver has been initialized */
+ if (!cpufreq_frequency_get_table(0))
+ return -EPROBE_DEFER;
+
+ cpumask_set_cpu(0, &mask_val);
+ cdev = cpufreq_cooling_register(&mask_val);
+
+ if (IS_ERR_OR_NULL(cdev)) {
+ dev_err(&pdev->dev, "Failed to register cooling device\n");
+ return PTR_ERR(cdev);
+ }
+
+ platform_set_drvdata(pdev, cdev);
+
+ dev_info(&pdev->dev, "Cooling device registered: %s\n", cdev->type);
+
+ return 0;
+}
+
+static int db8500_cpufreq_cooling_remove(struct platform_device *pdev)
+{
+ struct thermal_cooling_device *cdev = platform_get_drvdata(pdev);
+
+ cpufreq_cooling_unregister(cdev);
+
+ return 0;
+}
+
+static int db8500_cpufreq_cooling_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ return -ENOSYS;
+}
+
+static int db8500_cpufreq_cooling_resume(struct platform_device *pdev)
+{
+ return -ENOSYS;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id db8500_cpufreq_cooling_match[] = {
+ { .compatible = "stericsson,db8500-cpufreq-cooling" },
+ {},
+};
+#else
+#define db8500_cpufreq_cooling_match NULL
+#endif
+
+static struct platform_driver db8500_cpufreq_cooling_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "db8500-cpufreq-cooling",
+ .of_match_table = db8500_cpufreq_cooling_match,
+ },
+ .probe = db8500_cpufreq_cooling_probe,
+ .suspend = db8500_cpufreq_cooling_suspend,
+ .resume = db8500_cpufreq_cooling_resume,
+ .remove = db8500_cpufreq_cooling_remove,
+};
+
+static int __init db8500_cpufreq_cooling_init(void)
+{
+ return platform_driver_register(&db8500_cpufreq_cooling_driver);
+}
+
+static void __exit db8500_cpufreq_cooling_exit(void)
+{
+ platform_driver_unregister(&db8500_cpufreq_cooling_driver);
+}
+
+/* Should be later than db8500_cpufreq_register */
+late_initcall(db8500_cpufreq_cooling_init);
+module_exit(db8500_cpufreq_cooling_exit);
+
+MODULE_AUTHOR("Hongbo Zhang <hongbo.zhang@stericsson.com>");
+MODULE_DESCRIPTION("DB8500 cpufreq cooling driver");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,531 @@
+/*
+ * db8500_thermal.c - DB8500 Thermal Management Implementation
+ *
+ * Copyright (C) 2012 ST-Ericsson
+ * Copyright (C) 2012 Linaro Ltd.
+ *
+ * Author: Hongbo Zhang <hongbo.zhang@linaro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/cpu_cooling.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/dbx500-prcmu.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_data/db8500_thermal.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+
+#define PRCMU_DEFAULT_MEASURE_TIME 0xFFF
+#define PRCMU_DEFAULT_LOW_TEMP 0
+
+struct db8500_thermal_zone {
+ struct thermal_zone_device *therm_dev;
+ struct mutex th_lock;
+ struct work_struct therm_work;
+ struct db8500_thsens_platform_data *trip_tab;
+ enum thermal_device_mode mode;
+ enum thermal_trend trend;
+ unsigned long cur_temp_pseudo;
+ unsigned int cur_index;
+};
+
+/* Local function to check if thermal zone matches cooling devices */
+static int db8500_thermal_match_cdev(struct thermal_cooling_device *cdev,
+ struct db8500_trip_point *trip_point)
+{
+ int i;
+
+ if (!strlen(cdev->type))
+ return -EINVAL;
+
+ for (i = 0; i < COOLING_DEV_MAX; i++) {
+ if (!strcmp(trip_point->cdev_name[i], cdev->type))
+ return 0;
+ }
+
+ return -ENODEV;
+}
+
+/* Callback to bind cooling device to thermal zone */
+static int db8500_cdev_bind(struct thermal_zone_device *thermal,
+ struct thermal_cooling_device *cdev)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+ unsigned long max_state, upper, lower;
+ int i, ret = -EINVAL;
+
+ cdev->ops->get_max_state(cdev, &max_state);
+
+ for (i = 0; i < ptrips->num_trips; i++) {
+ if (db8500_thermal_match_cdev(cdev, &ptrips->trip_points[i]))
+ continue;
+
+ upper = lower = i > max_state ? max_state : i;
+
+ ret = thermal_zone_bind_cooling_device(thermal, i, cdev,
+ upper, lower);
+
+ dev_info(&cdev->device, "%s bind to %d: %d-%s\n", cdev->type,
+ i, ret, ret ? "fail" : "succeed");
+ }
+
+ return ret;
+}
+
+/* Callback to unbind cooling device from thermal zone */
+static int db8500_cdev_unbind(struct thermal_zone_device *thermal,
+ struct thermal_cooling_device *cdev)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+ int i, ret = -EINVAL;
+
+ for (i = 0; i < ptrips->num_trips; i++) {
+ if (db8500_thermal_match_cdev(cdev, &ptrips->trip_points[i]))
+ continue;
+
+ ret = thermal_zone_unbind_cooling_device(thermal, i, cdev);
+
+ dev_info(&cdev->device, "%s unbind from %d: %s\n", cdev->type,
+ i, ret ? "fail" : "succeed");
+ }
+
+ return ret;
+}
+
+/* Callback to get current temperature */
+static int db8500_sys_get_temp(struct thermal_zone_device *thermal,
+ unsigned long *temp)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+
+ /*
+ * TODO: There is no PRCMU interface to get temperature data currently,
+ * so a pseudo temperature is returned , it works for thermal framework
+ * and this will be fixed when the PRCMU interface is available.
+ */
+ *temp = pzone->cur_temp_pseudo;
+
+ return 0;
+}
+
+/* Callback to get temperature changing trend */
+static int db8500_sys_get_trend(struct thermal_zone_device *thermal,
+ int trip, enum thermal_trend *trend)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+
+ *trend = pzone->trend;
+
+ return 0;
+}
+
+/* Callback to get thermal zone mode */
+static int db8500_sys_get_mode(struct thermal_zone_device *thermal,
+ enum thermal_device_mode *mode)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+
+ mutex_lock(&pzone->th_lock);
+ *mode = pzone->mode;
+ mutex_unlock(&pzone->th_lock);
+
+ return 0;
+}
+
+/* Callback to set thermal zone mode */
+static int db8500_sys_set_mode(struct thermal_zone_device *thermal,
+ enum thermal_device_mode mode)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+
+ mutex_lock(&pzone->th_lock);
+
+ pzone->mode = mode;
+ if (mode == THERMAL_DEVICE_ENABLED)
+ schedule_work(&pzone->therm_work);
+
+ mutex_unlock(&pzone->th_lock);
+
+ return 0;
+}
+
+/* Callback to get trip point type */
+static int db8500_sys_get_trip_type(struct thermal_zone_device *thermal,
+ int trip, enum thermal_trip_type *type)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+
+ if (trip >= ptrips->num_trips)
+ return -EINVAL;
+
+ *type = ptrips->trip_points[trip].type;
+
+ return 0;
+}
+
+/* Callback to get trip point temperature */
+static int db8500_sys_get_trip_temp(struct thermal_zone_device *thermal,
+ int trip, unsigned long *temp)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+
+ if (trip >= ptrips->num_trips)
+ return -EINVAL;
+
+ *temp = ptrips->trip_points[trip].temp;
+
+ return 0;
+}
+
+/* Callback to get critical trip point temperature */
+static int db8500_sys_get_crit_temp(struct thermal_zone_device *thermal,
+ unsigned long *temp)
+{
+ struct db8500_thermal_zone *pzone = thermal->devdata;
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+ int i;
+
+ for (i = ptrips->num_trips - 1; i > 0; i--) {
+ if (ptrips->trip_points[i].type == THERMAL_TRIP_CRITICAL) {
+ *temp = ptrips->trip_points[i].temp;
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static struct thermal_zone_device_ops thdev_ops = {
+ .bind = db8500_cdev_bind,
+ .unbind = db8500_cdev_unbind,
+ .get_temp = db8500_sys_get_temp,
+ .get_trend = db8500_sys_get_trend,
+ .get_mode = db8500_sys_get_mode,
+ .set_mode = db8500_sys_set_mode,
+ .get_trip_type = db8500_sys_get_trip_type,
+ .get_trip_temp = db8500_sys_get_trip_temp,
+ .get_crit_temp = db8500_sys_get_crit_temp,
+};
+
+static void db8500_thermal_update_config(struct db8500_thermal_zone *pzone,
+ unsigned int idx, enum thermal_trend trend,
+ unsigned long next_low, unsigned long next_high)
+{
+ prcmu_stop_temp_sense();
+
+ pzone->cur_index = idx;
+ pzone->cur_temp_pseudo = (next_low + next_high)/2;
+ pzone->trend = trend;
+
+ prcmu_config_hotmon((u8)(next_low/1000), (u8)(next_high/1000));
+ prcmu_start_temp_sense(PRCMU_DEFAULT_MEASURE_TIME);
+}
+
+static irqreturn_t prcmu_low_irq_handler(int irq, void *irq_data)
+{
+ struct db8500_thermal_zone *pzone = irq_data;
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+ unsigned int idx = pzone->cur_index;
+ unsigned long next_low, next_high;
+
+ if (unlikely(idx == 0))
+ /* Meaningless for thermal management, ignoring it */
+ return IRQ_HANDLED;
+
+ if (idx == 1) {
+ next_high = ptrips->trip_points[0].temp;
+ next_low = PRCMU_DEFAULT_LOW_TEMP;
+ } else {
+ next_high = ptrips->trip_points[idx-1].temp;
+ next_low = ptrips->trip_points[idx-2].temp;
+ }
+ idx -= 1;
+
+ db8500_thermal_update_config(pzone, idx, THERMAL_TREND_DROPPING,
+ next_low, next_high);
+
+ dev_dbg(&pzone->therm_dev->device,
+ "PRCMU set max %ld, min %ld\n", next_high, next_low);
+
+ schedule_work(&pzone->therm_work);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t prcmu_high_irq_handler(int irq, void *irq_data)
+{
+ struct db8500_thermal_zone *pzone = irq_data;
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+ unsigned int idx = pzone->cur_index;
+ unsigned long next_low, next_high;
+
+ if (idx < ptrips->num_trips - 1) {
+ next_high = ptrips->trip_points[idx+1].temp;
+ next_low = ptrips->trip_points[idx].temp;
+ idx += 1;
+
+ db8500_thermal_update_config(pzone, idx, THERMAL_TREND_RAISING,
+ next_low, next_high);
+
+ dev_dbg(&pzone->therm_dev->device,
+ "PRCMU set max %ld, min %ld\n", next_high, next_low);
+ } else if (idx == ptrips->num_trips - 1)
+ pzone->cur_temp_pseudo = ptrips->trip_points[idx].temp + 1;
+
+ schedule_work(&pzone->therm_work);
+
+ return IRQ_HANDLED;
+}
+
+static void db8500_thermal_work(struct work_struct *work)
+{
+ enum thermal_device_mode cur_mode;
+ struct db8500_thermal_zone *pzone;
+
+ pzone = container_of(work, struct db8500_thermal_zone, therm_work);
+
+ mutex_lock(&pzone->th_lock);
+ cur_mode = pzone->mode;
+ mutex_unlock(&pzone->th_lock);
+
+ if (cur_mode == THERMAL_DEVICE_DISABLED)
+ return;
+
+ thermal_zone_device_update(pzone->therm_dev);
+ dev_dbg(&pzone->therm_dev->device, "thermal work finished.\n");
+}
+
+#ifdef CONFIG_OF
+static struct db8500_thsens_platform_data*
+ db8500_thermal_parse_dt(struct platform_device *pdev)
+{
+ struct db8500_thsens_platform_data *ptrips;
+ struct device_node *np = pdev->dev.of_node;
+ char prop_name[32];
+ const char *tmp_str;
+ u32 tmp_data;
+ int i, j;
+
+ ptrips = devm_kzalloc(&pdev->dev, sizeof(*ptrips), GFP_KERNEL);
+ if (!ptrips)
+ return NULL;
+
+ if (of_property_read_u32(np, "num-trips", &tmp_data))
+ goto err_parse_dt;
+
+ if (tmp_data > THERMAL_MAX_TRIPS)
+ goto err_parse_dt;
+
+ ptrips->num_trips = tmp_data;
+
+ for (i = 0; i < ptrips->num_trips; i++) {
+ sprintf(prop_name, "trip%d-temp", i);
+ if (of_property_read_u32(np, prop_name, &tmp_data))
+ goto err_parse_dt;
+
+ ptrips->trip_points[i].temp = tmp_data;
+
+ sprintf(prop_name, "trip%d-type", i);
+ if (of_property_read_string(np, prop_name, &tmp_str))
+ goto err_parse_dt;
+
+ if (!strcmp(tmp_str, "active"))
+ ptrips->trip_points[i].type = THERMAL_TRIP_ACTIVE;
+ else if (!strcmp(tmp_str, "passive"))
+ ptrips->trip_points[i].type = THERMAL_TRIP_PASSIVE;
+ else if (!strcmp(tmp_str, "hot"))
+ ptrips->trip_points[i].type = THERMAL_TRIP_HOT;
+ else if (!strcmp(tmp_str, "critical"))
+ ptrips->trip_points[i].type = THERMAL_TRIP_CRITICAL;
+ else
+ goto err_parse_dt;
+
+ sprintf(prop_name, "trip%d-cdev-num", i);
+ if (of_property_read_u32(np, prop_name, &tmp_data))
+ goto err_parse_dt;
+
+ if (tmp_data > COOLING_DEV_MAX)
+ goto err_parse_dt;
+
+ for (j = 0; j < tmp_data; j++) {
+ sprintf(prop_name, "trip%d-cdev-name%d", i, j);
+ if (of_property_read_string(np, prop_name, &tmp_str))
+ goto err_parse_dt;
+
+ if (strlen(tmp_str) >= THERMAL_NAME_LENGTH)
+ goto err_parse_dt;
+
+ strcpy(ptrips->trip_points[i].cdev_name[j], tmp_str);
+ }
+ }
+ return ptrips;
+
+err_parse_dt:
+ dev_err(&pdev->dev, "Parsing device tree data error.\n");
+ return NULL;
+}
+#else
+static inline struct db8500_thsens_platform_data*
+ db8500_thermal_parse_dt(struct platform_device *pdev)
+{
+ return NULL;
+}
+#endif
+
+static int db8500_thermal_probe(struct platform_device *pdev)
+{
+ struct db8500_thermal_zone *pzone = NULL;
+ struct db8500_thsens_platform_data *ptrips = NULL;
+ struct device_node *np = pdev->dev.of_node;
+ int low_irq, high_irq, ret = 0;
+ unsigned long dft_low, dft_high;
+
+ if (np)
+ ptrips = db8500_thermal_parse_dt(pdev);
+ else
+ ptrips = dev_get_platdata(&pdev->dev);
+
+ if (!ptrips)
+ return -EINVAL;
+
+ pzone = devm_kzalloc(&pdev->dev, sizeof(*pzone), GFP_KERNEL);
+ if (!pzone)
+ return -ENOMEM;
+
+ mutex_init(&pzone->th_lock);
+ mutex_lock(&pzone->th_lock);
+
+ pzone->mode = THERMAL_DEVICE_DISABLED;
+ pzone->trip_tab = ptrips;
+
+ INIT_WORK(&pzone->therm_work, db8500_thermal_work);
+
+ low_irq = platform_get_irq_byname(pdev, "IRQ_HOTMON_LOW");
+ if (low_irq < 0) {
+ dev_err(&pdev->dev, "Get IRQ_HOTMON_LOW failed.\n");
+ return low_irq;
+ }
+
+ ret = devm_request_threaded_irq(&pdev->dev, low_irq, NULL,
+ prcmu_low_irq_handler, IRQF_NO_SUSPEND | IRQF_ONESHOT,
+ "dbx500_temp_low", pzone);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to allocate temp low irq.\n");
+ return ret;
+ }
+
+ high_irq = platform_get_irq_byname(pdev, "IRQ_HOTMON_HIGH");
+ if (high_irq < 0) {
+ dev_err(&pdev->dev, "Get IRQ_HOTMON_HIGH failed.\n");
+ return high_irq;
+ }
+
+ ret = devm_request_threaded_irq(&pdev->dev, high_irq, NULL,
+ prcmu_high_irq_handler, IRQF_NO_SUSPEND | IRQF_ONESHOT,
+ "dbx500_temp_high", pzone);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to allocate temp high irq.\n");
+ return ret;
+ }
+
+ pzone->therm_dev = thermal_zone_device_register("db8500_thermal_zone",
+ ptrips->num_trips, 0, pzone, &thdev_ops, 0, 0);
+
+ if (IS_ERR_OR_NULL(pzone->therm_dev)) {
+ dev_err(&pdev->dev, "Register thermal zone device failed.\n");
+ return PTR_ERR(pzone->therm_dev);
+ }
+ dev_info(&pdev->dev, "Thermal zone device registered.\n");
+
+ dft_low = PRCMU_DEFAULT_LOW_TEMP;
+ dft_high = ptrips->trip_points[0].temp;
+
+ db8500_thermal_update_config(pzone, 0, THERMAL_TREND_STABLE,
+ dft_low, dft_high);
+
+ platform_set_drvdata(pdev, pzone);
+ pzone->mode = THERMAL_DEVICE_ENABLED;
+ mutex_unlock(&pzone->th_lock);
+
+ return 0;
+}
+
+static int db8500_thermal_remove(struct platform_device *pdev)
+{
+ struct db8500_thermal_zone *pzone = platform_get_drvdata(pdev);
+
+ thermal_zone_device_unregister(pzone->therm_dev);
+ cancel_work_sync(&pzone->therm_work);
+ mutex_destroy(&pzone->th_lock);
+
+ return 0;
+}
+
+static int db8500_thermal_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ struct db8500_thermal_zone *pzone = platform_get_drvdata(pdev);
+
+ flush_work(&pzone->therm_work);
+ prcmu_stop_temp_sense();
+
+ return 0;
+}
+
+static int db8500_thermal_resume(struct platform_device *pdev)
+{
+ struct db8500_thermal_zone *pzone = platform_get_drvdata(pdev);
+ struct db8500_thsens_platform_data *ptrips = pzone->trip_tab;
+ unsigned long dft_low, dft_high;
+
+ dft_low = PRCMU_DEFAULT_LOW_TEMP;
+ dft_high = ptrips->trip_points[0].temp;
+
+ db8500_thermal_update_config(pzone, 0, THERMAL_TREND_STABLE,
+ dft_low, dft_high);
+
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id db8500_thermal_match[] = {
+ { .compatible = "stericsson,db8500-thermal" },
+ {},
+};
+#else
+#define db8500_thermal_match NULL
+#endif
+
+static struct platform_driver db8500_thermal_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "db8500-thermal",
+ .of_match_table = db8500_thermal_match,
+ },
+ .probe = db8500_thermal_probe,
+ .suspend = db8500_thermal_suspend,
+ .resume = db8500_thermal_resume,
+ .remove = db8500_thermal_remove,
+};
+
+module_platform_driver(db8500_thermal_driver);
+
+MODULE_AUTHOR("Hongbo Zhang <hongbo.zhang@stericsson.com>");
+MODULE_DESCRIPTION("DB8500 thermal driver");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,38 @@
+/*
+ * db8500_thermal.h - DB8500 Thermal Management Implementation
+ *
+ * Copyright (C) 2012 ST-Ericsson
+ * Copyright (C) 2012 Linaro Ltd.
+ *
+ * Author: Hongbo Zhang <hongbo.zhang@linaro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DB8500_THERMAL_H_
+#define _DB8500_THERMAL_H_
+
+#include <linux/thermal.h>
+
+#define COOLING_DEV_MAX 8
+
+struct db8500_trip_point {
+ unsigned long temp;
+ enum thermal_trip_type type;
+ char cdev_name[COOLING_DEV_MAX][THERMAL_NAME_LENGTH];
+};
+
+struct db8500_thsens_platform_data {
+ struct db8500_trip_point trip_points[THERMAL_MAX_TRIPS];
+ int num_trips;
+};
+
+#endif /* _DB8500_THERMAL_H_ */