new file mode 100644
@@ -0,0 +1,27 @@
+Qualcomm QPNP PMIC Temperature Alarm
+
+QPNP temperature alarm peripherals are found inside of Qualcomm PMIC chips
+that utilize the Qualcomm SPMI implementation. These peripherals provide an
+interrupt signal and status register to identify high PMIC die temperature.
+
+Required properties:
+- compatible: Should contain "qcom,qpnp-temp-alarm".
+- reg: Specifies the SPMI address temperature alarm device.
+- interrupts: PMIC temperature alarm interrupt
+
+Optional properties:
+- label: A string used as a descriptive name for this thermal
+ device. This name should be 19 characters or less.
+- io-channels: Should contain IIO channel specifier
+- io-channel-names: "thermal". The ADC channel for volatage reading.
+
+Example:
+
+ thermal-alarm@2400 {
+ compatible = "qcom,qpnp-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+ label = "pm8941_tz";
+ io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
+ io-channel-names = "thermal";
+ };
@@ -248,4 +248,16 @@ depends on ARCH_STI && OF
source "drivers/thermal/st/Kconfig"
endmenu
+config QPNP_TEMP_ALARM
+ tristate "Qualcomm QPNP Temperature Alarm"
+ depends on OF && REGMAP_SPMI
+ help
+ This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP)
+ PMIC devices. It shows up in sysfs as a thermal zone with multiple
+ trip points. The temperature reported by the thermal zone reflects the
+ real time die temperature if an ADC is present or an estimate of the
+ temperature based upon the over temperature stage value. Enabling the
+ thermal zone device via the mode file results in shifting PMIC over
+ temperature shutdown control from hardware to software.
+
endif
@@ -33,3 +33,4 @@ obj-$(CONFIG_INTEL_SOC_DTS_THERMAL) += intel_soc_dts_thermal.o
obj-$(CONFIG_TI_SOC_THERMAL) += ti-soc-thermal/
obj-$(CONFIG_ACPI_INT3403_THERMAL) += int3403_thermal.o
obj-$(CONFIG_ST_THERMAL) += st/
+obj-$(CONFIG_QPNP_TEMP_ALARM) += qpnp-temp-alarm.o
new file mode 100644
@@ -0,0 +1,519 @@
+/*
+ * Copyright (c) 2011-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/iio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+
+#define QPNP_TM_REG_TYPE 0x04
+#define QPNP_TM_REG_SUBTYPE 0x05
+#define QPNP_TM_REG_STATUS 0x08
+#define QPNP_TM_REG_SHUTDOWN_CTRL1 0x40
+#define QPNP_TM_REG_SHUTDOWN_CTRL2 0x42
+#define QPNP_TM_REG_ALARM_CTRL 0x46
+
+#define QPNP_TM_TYPE 0x09
+#define QPNP_TM_SUBTYPE 0x08
+
+#define STATUS_STAGE_MASK 0x03
+
+#define SHUTDOWN_CTRL1_OVERRIDE_STAGE3 0x80
+#define SHUTDOWN_CTRL1_OVERRIDE_STAGE2 0x40
+#define SHUTDOWN_CTRL1_THRESHOLD_MASK 0x03
+
+#define SHUTDOWN_CTRL2_CLEAR_STAGE3 0x80
+#define SHUTDOWN_CTRL2_CLEAR_STAGE2 0x40
+
+#define ALARM_CTRL_FORCE_ENABLE 0x80
+#define ALARM_CTRL_FOLLOW_HW_ENABLE 0x01
+
+/*
+ * Trip point values based on threshold control
+ * 0 = {105 C, 125 C, 145 C}
+ * 1 = {110 C, 130 C, 150 C}
+ * 2 = {115 C, 135 C, 155 C}
+ * 3 = {120 C, 140 C, 160 C}
+*/
+#define TEMP_STAGE_STEP 20000 /* Stage step: 20.000 C */
+#define TEMP_STAGE_HYSTERESIS 2000
+
+#define TEMP_THRESH_MIN 105000 /* Threshold Min: 105 C */
+#define TEMP_THRESH_STEP 5000 /* Threshold step: 5 C */
+
+#define THRESH_MIN 0
+#define THRESH_MAX 3
+
+/* Trip points from most critical to least critical */
+#define TRIP_STAGE3 0
+#define TRIP_STAGE2 1
+#define TRIP_STAGE1 2
+#define TRIP_NUM 3
+
+/* Delay between TEMP_STAT IRQ going high and status value changing in ms */
+#define READ_DELAY_MS 40
+
+/* 2000 uV/K */
+#define MICRO_VOLTS_TO_MILI_CELSIUS(x) ((x) / 2 - 273150)
+
+/* Temperature in Milli Celsius reported during stage 0 if no ADC is present */
+#define DEFAULT_TEMP 37000
+
+struct qpnp_tm_chip {
+ struct delayed_work work;
+ struct regmap *map;
+ struct device *dev;
+ struct thermal_zone_device *tz_dev;
+ enum thermal_device_mode mode;
+ const char *tm_name;
+ int irq;
+ long temp;
+ unsigned int thresh;
+ unsigned int stage;
+ unsigned int prev_stage;
+ unsigned int base;
+ struct iio_channel *adc;
+};
+
+static inline int qpnp_tm_read(struct qpnp_tm_chip *chip, u16 addr, u8 *buf)
+{
+ return regmap_bulk_read(chip->map, chip->base + addr, buf, 1);
+}
+
+static inline int qpnp_tm_write(struct qpnp_tm_chip *chip, u16 addr, u8 *buf)
+{
+ return regmap_bulk_write(chip->map, chip->base + addr, buf, 1);
+}
+
+static int qpnp_tm_shutdown_override(struct qpnp_tm_chip *chip, bool enable)
+{
+ u8 reg;
+
+ reg = chip->thresh & SHUTDOWN_CTRL1_THRESHOLD_MASK;
+
+ if (enable) {
+ reg |= SHUTDOWN_CTRL1_OVERRIDE_STAGE2;
+ reg |= SHUTDOWN_CTRL1_OVERRIDE_STAGE3;
+ }
+
+ return qpnp_tm_write(chip, QPNP_TM_REG_SHUTDOWN_CTRL1, ®);
+}
+
+/*
+ * This function updates the internal temp value based on the
+ * current thermal stage and threshold as well as the previous stage
+ */
+static int qpnp_tm_update_temp_no_adc(struct qpnp_tm_chip *chip)
+{
+ unsigned int stage;
+ int rc;
+ u8 reg;
+
+ rc = qpnp_tm_read(chip, QPNP_TM_REG_STATUS, ®);
+ if (rc < 0)
+ return rc;
+
+ stage = reg & STATUS_STAGE_MASK;
+
+ if (stage > chip->stage) {
+ /* increasing stage, use lower bound */
+ chip->temp = (stage - 1) * TEMP_STAGE_STEP +
+ chip->thresh * TEMP_THRESH_STEP +
+ TEMP_STAGE_HYSTERESIS + TEMP_THRESH_MIN;
+ } else if (stage < chip->stage) {
+ /* decreasing stage, use upper bound */
+ chip->temp = stage * TEMP_STAGE_STEP +
+ chip->thresh * TEMP_THRESH_STEP -
+ TEMP_STAGE_HYSTERESIS + TEMP_THRESH_MIN;
+ }
+
+ chip->stage = stage;
+
+ return 0;
+}
+
+static int qpnp_tz_get_temp(struct thermal_zone_device *thermal,
+ unsigned long *temp)
+{
+ struct qpnp_tm_chip *chip = thermal->devdata;
+ int rc, uv;
+
+ if (!temp)
+ return -EINVAL;
+
+ if (IS_ERR(chip->adc)) {
+ rc = qpnp_tm_update_temp_no_adc(chip);
+ if (rc < 0)
+ return rc;
+ } else {
+ rc = iio_read_channel_processed(chip->adc, &uv);
+ if (rc < 0)
+ return rc;
+
+ chip->temp = MICRO_VOLTS_TO_MILI_CELSIUS(uv);
+ }
+
+ *temp = chip->temp < 0 ? 0 : chip->temp;
+
+ return 0;
+}
+
+static int qpnp_tz_get_mode(struct thermal_zone_device *thermal,
+ enum thermal_device_mode *mode)
+{
+ struct qpnp_tm_chip *chip = thermal->devdata;
+
+ if (!mode)
+ return -EINVAL;
+
+ *mode = chip->mode;
+
+ return 0;
+}
+
+static int qpnp_tz_set_mode(struct thermal_zone_device *thermal,
+ enum thermal_device_mode mode)
+{
+ struct qpnp_tm_chip *chip = thermal->devdata;
+ int rc;
+
+ if (mode == chip->mode)
+ return 0;
+
+ if (mode == THERMAL_DEVICE_ENABLED)
+ rc = qpnp_tm_shutdown_override(chip, true);
+ else
+ rc = qpnp_tm_shutdown_override(chip, false);
+
+ chip->mode = mode;
+
+ return rc;
+}
+
+static int qpnp_tz_get_trip_type(struct thermal_zone_device *thermal, int trip,
+ enum thermal_trip_type *type)
+{
+ if (trip < 0 || !type)
+ return -EINVAL;
+
+ switch (trip) {
+ case TRIP_STAGE3:
+ *type = THERMAL_TRIP_CRITICAL;
+ break;
+ case TRIP_STAGE2:
+ *type = THERMAL_TRIP_HOT;
+ break;
+ case TRIP_STAGE1:
+ *type = THERMAL_TRIP_HOT;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int qpnp_tz_get_trip_temp(struct thermal_zone_device *thermal, int trip,
+ unsigned long *temp)
+{
+ struct qpnp_tm_chip *chip = thermal->devdata;
+ int thresh_temp;
+
+ if (trip < 0 || !temp)
+ return -EINVAL;
+
+ thresh_temp = chip->thresh * TEMP_THRESH_STEP + TEMP_THRESH_MIN;
+
+ switch (trip) {
+ case TRIP_STAGE3:
+ thresh_temp += 2 * TEMP_STAGE_STEP;
+ break;
+ case TRIP_STAGE2:
+ thresh_temp += TEMP_STAGE_STEP;
+ break;
+ case TRIP_STAGE1:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ *temp = thresh_temp;
+
+ return 0;
+}
+
+static int qpnp_tz_get_crit_temp(struct thermal_zone_device *thermal,
+ unsigned long *temp)
+{
+ struct qpnp_tm_chip *chip = thermal->devdata;
+
+ if (!temp)
+ return -EINVAL;
+
+ *temp = chip->thresh * TEMP_THRESH_STEP + TEMP_THRESH_MIN +
+ 2 * TEMP_STAGE_STEP;
+
+ return 0;
+}
+
+static irqreturn_t qpnp_tm_isr(int irq, void *data)
+{
+ struct qpnp_tm_chip *chip = data;
+
+ schedule_delayed_work(&chip->work, msecs_to_jiffies(READ_DELAY_MS) + 1);
+
+ return IRQ_HANDLED;
+}
+
+static void qpnp_tm_work(struct work_struct *work)
+{
+ struct delayed_work *dwork;
+ struct qpnp_tm_chip *chip;
+ int rc, uv;
+ u8 reg;
+
+ dwork = container_of(work, struct delayed_work, work);
+ chip = container_of(dwork, struct qpnp_tm_chip, work);
+
+ if (IS_ERR(chip->adc)) {
+ rc = qpnp_tm_update_temp_no_adc(chip);
+ if (rc < 0)
+ return;
+ } else {
+ rc = qpnp_tm_read(chip, QPNP_TM_REG_STATUS, ®);
+ if (rc < 0)
+ return;
+
+ chip->stage = reg & STATUS_STAGE_MASK;
+
+ rc = iio_read_channel_processed(chip->adc, &uv);
+ if (rc < 0)
+ return;
+
+ chip->temp = MICRO_VOLTS_TO_MILI_CELSIUS(uv);
+ }
+
+ if (chip->stage != chip->prev_stage) {
+ chip->prev_stage = chip->stage;
+
+ dev_warn(chip->dev, "Thermal alarm stage %u, threshold %u, temp %ld mC\n",
+ chip->stage, chip->thresh, chip->temp);
+
+ thermal_zone_device_update(chip->tz_dev);
+
+ /* Notify user space */
+ sysfs_notify(&chip->tz_dev->device.kobj, NULL, "type");
+ }
+}
+
+/*
+ * This function initializes the internal temp value based on only the
+ * current thermal stage and threshold. Setup threshold control and
+ * disable shutdown override.
+ */
+static int qpnp_tm_init(struct qpnp_tm_chip *chip)
+{
+ int rc;
+ u8 reg;
+
+ chip->thresh = THRESH_MIN;
+ chip->temp = DEFAULT_TEMP;
+
+ rc = qpnp_tm_read(chip, QPNP_TM_REG_STATUS, ®);
+ if (rc < 0)
+ return rc;
+
+ chip->stage = reg & STATUS_STAGE_MASK;
+
+ if (chip->stage)
+ chip->temp = chip->thresh * TEMP_THRESH_STEP +
+ (chip->stage - 1) * TEMP_STAGE_STEP +
+ TEMP_THRESH_MIN;
+
+ /*
+ * Set threshold and disable software override of stage 2 and 3
+ * shutdowns.
+ */
+ reg = chip->thresh & SHUTDOWN_CTRL1_THRESHOLD_MASK;
+ rc = qpnp_tm_write(chip, QPNP_TM_REG_SHUTDOWN_CTRL1, ®);
+ if (rc < 0)
+ return rc;
+
+ /* Enable the thermal alarm PMIC module in always-on mode. */
+ reg = ALARM_CTRL_FORCE_ENABLE;
+ rc = qpnp_tm_write(chip, QPNP_TM_REG_ALARM_CTRL, ®);
+
+ return rc;
+}
+
+static struct thermal_zone_device_ops qpnp_tz_ops = {
+ .get_temp = qpnp_tz_get_temp,
+ .get_mode = qpnp_tz_get_mode,
+ .set_mode = qpnp_tz_set_mode,
+ .get_trip_type = qpnp_tz_get_trip_type,
+ .get_trip_temp = qpnp_tz_get_trip_temp,
+ .get_crit_temp = qpnp_tz_get_crit_temp,
+};
+
+static int qpnp_tm_probe(struct platform_device *pdev)
+{
+ struct qpnp_tm_chip *chip;
+ struct device_node *node;
+ struct resource *res;
+ u8 type, subtype;
+ int rc = 0;
+
+ node = pdev->dev.of_node;
+
+ chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ dev_set_drvdata(&pdev->dev, chip);
+
+ chip->dev = &pdev->dev;
+ INIT_DELAYED_WORK(&chip->work, qpnp_tm_work);
+
+ chip->map = dev_get_regmap(chip->dev->parent, NULL);
+ if (!chip->map)
+ return -ENXIO;
+
+ res = platform_get_resource(pdev, IORESOURCE_REG, 0);
+ if (!res)
+ return -ENXIO;
+
+ chip->base = res->start;
+
+ rc = qpnp_tm_read(chip, QPNP_TM_REG_TYPE, &type);
+ if (rc < 0) {
+ dev_err(&pdev->dev, "could not read type\n");
+ return rc;
+ }
+
+ rc = qpnp_tm_read(chip, QPNP_TM_REG_SUBTYPE, &subtype);
+ if (rc < 0) {
+ dev_err(&pdev->dev, "could not read subtype\n");
+ return rc;
+ }
+
+ if (type != QPNP_TM_TYPE || subtype != QPNP_TM_SUBTYPE) {
+ dev_err(&pdev->dev, "invalid type %02x or subtype %02x\n",
+ type, subtype);
+ return -ENODEV;
+ }
+
+ chip->irq = platform_get_irq(pdev, 0);
+ if (chip->irq < 0)
+ return chip->irq;
+
+ chip->tm_name = of_get_property(node, "label", NULL);
+ if (!chip->tm_name)
+ chip->tm_name = dev_name(chip->dev);
+
+ chip->adc = iio_channel_get(chip->dev, "thermal");
+ if (PTR_ERR(chip->adc) == -EPROBE_DEFER)
+ return PTR_ERR(chip->adc);
+
+ rc = qpnp_tm_init(chip);
+ if (rc < 0) {
+ dev_err(&pdev->dev, "init failed\n");
+ return rc;
+ }
+
+ /* Start in HW control. Switch to SW control when user changes mode. */
+ chip->mode = THERMAL_DEVICE_DISABLED;
+
+ chip->tz_dev = thermal_zone_device_register(chip->tm_name, TRIP_NUM, 0,
+ chip, &qpnp_tz_ops, NULL,
+ 0, 0);
+ if (IS_ERR(chip->tz_dev)) {
+ dev_err(&pdev->dev, "TZ registration failed\n");
+ return PTR_ERR(chip->tz_dev);
+ }
+
+ rc = devm_request_irq(chip->dev, chip->irq, qpnp_tm_isr,
+ IRQF_TRIGGER_RISING, chip->tm_name, chip);
+ if (rc < 0)
+ thermal_zone_device_unregister(chip->tz_dev);
+
+ return rc;
+}
+
+static int qpnp_tm_remove(struct platform_device *pdev)
+{
+ struct qpnp_tm_chip *chip = dev_get_drvdata(&pdev->dev);
+
+ cancel_delayed_work_sync(&chip->work);
+ thermal_zone_device_unregister(chip->tz_dev);
+ qpnp_tm_shutdown_override(chip, false);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int qpnp_tm_suspend(struct device *dev)
+{
+ struct qpnp_tm_chip *chip = dev_get_drvdata(dev);
+
+ /* Clear override bits in suspend to allow hardware control */
+ qpnp_tm_shutdown_override(chip, false);
+
+ return 0;
+}
+
+static int qpnp_tm_resume(struct device *dev)
+{
+ struct qpnp_tm_chip *chip = dev_get_drvdata(dev);
+
+ /* Override hardware actions so software can control */
+ if (chip->mode == THERMAL_DEVICE_ENABLED)
+ qpnp_tm_shutdown_override(chip, true);
+
+ return 0;
+}
+
+static const struct dev_pm_ops qpnp_tm_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(qpnp_tm_suspend, qpnp_tm_resume)
+};
+
+#define QPNP_TM_PM_OPS (&qpnp_tm_pm_ops)
+#else
+#define QPNP_TM_PM_OPS NULL
+#endif
+
+static struct of_device_id qpnp_tm_match_table[] = {
+ { .compatible = "qcom,qpnp-temp-alarm" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qpnp_tm_match_table);
+
+static struct platform_driver qpnp_tm_driver = {
+ .driver = {
+ .name = "qpnp-temp-alarm",
+ .of_match_table = qpnp_tm_match_table,
+ .owner = THIS_MODULE,
+ .pm = QPNP_TM_PM_OPS,
+ },
+ .probe = qpnp_tm_probe,
+ .remove = qpnp_tm_remove,
+};
+module_platform_driver(qpnp_tm_driver);
+
+MODULE_DESCRIPTION("QPNP PMIC Temperature Alarm driver");
+MODULE_LICENSE("GPL v2");
Add support for the temperature alarm peripheral found inside Qualcomm plug-and-play (QPNP) PMIC chips. The temperature alarm peripheral outputs a pulse on an interrupt line whenever the thermal over temperature stage value changes. Implement an ISR to manage this interrupt. Register a thermal zone device in sysfs with mulitple trip points corresponding to the physical threshold temperatures between over temperature stages. The temperature reported by this thermal zone device should reflect the actual PMIC die temperature if an ADC is present on the given PMIC. If no ADC is present, then the reported temperature should be estimated from the over temperature stage value. Send a notification to userspace via sysfs_notify() whenever the over temperature stage value changes. Cc: David Collins <collinsd@codeaurora.org> Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> --- .../bindings/thermal/qpnp-temp-alarm.txt | 27 ++ drivers/thermal/Kconfig | 12 + drivers/thermal/Makefile | 1 + drivers/thermal/qpnp-temp-alarm.c | 519 +++++++++++++++++++++ 4 files changed, 559 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/qpnp-temp-alarm.txt create mode 100644 drivers/thermal/qpnp-temp-alarm.c