| Message ID | 20191219082927.11898-3-m.szyprowski@samsung.com (mailing list archive) |
|---|---|
| State | Superseded |
| Delegated to: | Chanwoo Choi |
| Headers | show |
| Series | [1/2] ARM: dts: exynos: Move bus related OPPs to the boards DTS | expand |
Hi Marek, On 12/19/19 5:29 PM, Marek Szyprowski wrote: > Hardkernel's Odroid XU3/XU4/HC1 boards use bootloader, which configures top > PLLs to the following values: MPLL: 532MHz, CPLL: 666MHz and DPLL: 600MHz. > > Adjust all bus related OPPs to the values that are possible to derive from > the top PLL configured by the bootloader. Also add a comment for each bus > describing which PLL is used for it. > > The most significant change is the highest rate for wcore bus. It has been > increased to 532MHz as this is the value configured initially by the > bootloader. Also the voltage for this OPP is changed to match the value > set by the bootloader. > > This patch finally allows the buses to operate on the rates matching the > values set for each OPP and fixes the following warnings observed on boot: > > exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz) > exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz) > exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz) > ... > exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34) > exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34) > exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34) > > The problem with setting incorrect (in some cases much lower) clock rate > for the defined OPP were there from the beginning, but went unnoticed > because the only way to observe it was to manually check the rate of the > respective clocks. The commit 4294a779bd8d ("PM / devfreq: exynos-bus: > Convert to use dev_pm_opp_set_rate()") finally revealed it, because it > enabled use of the generic code from the OPP framework, which issues the > above mentioned warnings. > > Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> > --- > arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 75 +++++++++++-------- > 1 file changed, 45 insertions(+), 30 deletions(-) > > diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi > index 663a38d53c9e..b6d6022e8735 100644 > --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi > +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi > @@ -38,42 +38,44 @@ > bus_wcore_opp_table: opp_table2 { > compatible = "operating-points-v2"; > > + /* derived from 532MHz MPLL */ > opp00 { > - opp-hz = /bits/ 64 <84000000>; > + opp-hz = /bits/ 64 <88700000>; > opp-microvolt = <925000 925000 1400000>; > }; > opp01 { > - opp-hz = /bits/ 64 <111000000>; > + opp-hz = /bits/ 64 <133000000>; > opp-microvolt = <950000 950000 1400000>; > }; > opp02 { > - opp-hz = /bits/ 64 <222000000>; > + opp-hz = /bits/ 64 <177400000>; > opp-microvolt = <950000 950000 1400000>; > }; > opp03 { > - opp-hz = /bits/ 64 <333000000>; > + opp-hz = /bits/ 64 <266000000>; > opp-microvolt = <950000 950000 1400000>; > }; > opp04 { > - opp-hz = /bits/ 64 <400000000>; > - opp-microvolt = <987500 987500 1400000>; > + opp-hz = /bits/ 64 <532000000>; > + opp-microvolt = <1000000 1000000 1400000>; > }; > }; > > bus_noc_opp_table: opp_table3 { > compatible = "operating-points-v2"; > > + /* derived from 666MHz CPLL */ > opp00 { > - opp-hz = /bits/ 64 <67000000>; > + opp-hz = /bits/ 64 <66600000>; > }; > opp01 { > - opp-hz = /bits/ 64 <75000000>; > + opp-hz = /bits/ 64 <74000000>; > }; > opp02 { > - opp-hz = /bits/ 64 <86000000>; > + opp-hz = /bits/ 64 <83250000>; > }; > opp03 { > - opp-hz = /bits/ 64 <100000000>; > + opp-hz = /bits/ 64 <111000000>; > }; > }; > > @@ -81,39 +83,42 @@ > compatible = "operating-points-v2"; > opp-shared; > > + /* derived from 666MHz CPLL */ > opp00 { > - opp-hz = /bits/ 64 <100000000>; > + opp-hz = /bits/ 64 <111000000>; > }; > opp01 { > - opp-hz = /bits/ 64 <200000000>; > + opp-hz = /bits/ 64 <222000000>; > }; > }; > > bus_fsys2_opp_table: opp_table5 { > compatible = "operating-points-v2"; > > + /* derived from 600MHz DPLL */ > opp00 { > opp-hz = /bits/ 64 <75000000>; > }; > opp01 { > - opp-hz = /bits/ 64 <100000000>; > + opp-hz = /bits/ 64 <120000000>; > }; > opp02 { > - opp-hz = /bits/ 64 <150000000>; > + opp-hz = /bits/ 64 <200000000>; > }; > }; > > bus_mfc_opp_table: opp_table6 { > compatible = "operating-points-v2"; > > + /* derived from 666MHz CPLL */ > opp00 { > - opp-hz = /bits/ 64 <96000000>; > + opp-hz = /bits/ 64 <83250000>; > }; > opp01 { > opp-hz = /bits/ 64 <111000000>; > }; > opp02 { > - opp-hz = /bits/ 64 <167000000>; > + opp-hz = /bits/ 64 <166500000>; > }; > opp03 { > opp-hz = /bits/ 64 <222000000>; > @@ -126,8 +131,9 @@ > bus_gen_opp_table: opp_table7 { > compatible = "operating-points-v2"; > > + /* derived from 532MHz MPLL */ > opp00 { > - opp-hz = /bits/ 64 <89000000>; > + opp-hz = /bits/ 64 <88700000>; > }; > opp01 { > opp-hz = /bits/ 64 <133000000>; > @@ -136,32 +142,34 @@ > opp-hz = /bits/ 64 <178000000>; > }; > opp03 { > - opp-hz = /bits/ 64 <267000000>; > + opp-hz = /bits/ 64 <266000000>; > }; > }; > > bus_peri_opp_table: opp_table8 { > compatible = "operating-points-v2"; > > + /* derived from 666MHz CPLL */ > opp00 { > - opp-hz = /bits/ 64 <67000000>; > + opp-hz = /bits/ 64 <66600000>; > }; > }; > > bus_g2d_opp_table: opp_table9 { > compatible = "operating-points-v2"; > > + /* derived from 666MHz CPLL */ > opp00 { > - opp-hz = /bits/ 64 <84000000>; > + opp-hz = /bits/ 64 <83250000>; > }; > opp01 { > - opp-hz = /bits/ 64 <167000000>; > + opp-hz = /bits/ 64 <111000000>; > }; > opp02 { > - opp-hz = /bits/ 64 <222000000>; > + opp-hz = /bits/ 64 <166500000>; > }; > opp03 { > - opp-hz = /bits/ 64 <300000000>; > + opp-hz = /bits/ 64 <222000000>; > }; > opp04 { > opp-hz = /bits/ 64 <333000000>; > @@ -171,8 +179,9 @@ > bus_g2d_acp_opp_table: opp_table10 { > compatible = "operating-points-v2"; > > + /* derived from 532MHz MPLL */ > opp00 { > - opp-hz = /bits/ 64 <67000000>; > + opp-hz = /bits/ 64 <66500000>; > }; > opp01 { > opp-hz = /bits/ 64 <133000000>; > @@ -181,13 +190,14 @@ > opp-hz = /bits/ 64 <178000000>; > }; > opp03 { > - opp-hz = /bits/ 64 <267000000>; > + opp-hz = /bits/ 64 <266000000>; > }; > }; > > bus_jpeg_opp_table: opp_table11 { > compatible = "operating-points-v2"; > > + /* derived from 600MHz DPLL */ > opp00 { > opp-hz = /bits/ 64 <75000000>; > }; > @@ -205,23 +215,25 @@ > bus_jpeg_apb_opp_table: opp_table12 { > compatible = "operating-points-v2"; > > + /* derived from 666MHz CPLL */ > opp00 { > - opp-hz = /bits/ 64 <84000000>; > + opp-hz = /bits/ 64 <83250000>; > }; > opp01 { > opp-hz = /bits/ 64 <111000000>; > }; > opp02 { > - opp-hz = /bits/ 64 <134000000>; > + opp-hz = /bits/ 64 <133000000>; > }; > opp03 { > - opp-hz = /bits/ 64 <167000000>; > + opp-hz = /bits/ 64 <166500000>; > }; > }; > > bus_disp1_fimd_opp_table: opp_table13 { > compatible = "operating-points-v2"; > > + /* derived from 600MHz DPLL */ > opp00 { > opp-hz = /bits/ 64 <120000000>; > }; > @@ -233,6 +245,7 @@ > bus_disp1_opp_table: opp_table14 { > compatible = "operating-points-v2"; > > + /* derived from 600MHz DPLL */ > opp00 { > opp-hz = /bits/ 64 <120000000>; > }; > @@ -247,6 +260,7 @@ > bus_gscl_opp_table: opp_table15 { > compatible = "operating-points-v2"; > > + /* derived from 600MHz DPLL */ > opp00 { > opp-hz = /bits/ 64 <150000000>; > }; > @@ -261,6 +275,7 @@ > bus_mscl_opp_table: opp_table16 { > compatible = "operating-points-v2"; > > + /* derived from 666MHz CPLL */ > opp00 { > opp-hz = /bits/ 64 <84000000>; > }; > @@ -274,7 +289,7 @@ > opp-hz = /bits/ 64 <333000000>; > }; > opp04 { > - opp-hz = /bits/ 64 <400000000>; > + opp-hz = /bits/ 64 <666000000>; > }; > }; > > @@ -398,7 +413,7 @@ > }; > > &bus_fsys { > - operating-points-v2 = <&bus_fsys_apb_opp_table>; > + operating-points-v2 = <&bus_fsys2_opp_table>; Need to remove 'opp-shared' property in bus_fsys_apb_opp_table. And need to add 'opp-shared' property to bus_fsys2_opp_table. > devfreq = <&bus_wcore>; > status = "okay"; > }; > If you fix the things related to 'opp-shared', Looks good to me. Tested-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Hi Chanwoo, On 19.12.2019 10:07, Chanwoo Choi wrote: > On 12/19/19 5:29 PM, Marek Szyprowski wrote: >> Hardkernel's Odroid XU3/XU4/HC1 boards use bootloader, which configures top >> PLLs to the following values: MPLL: 532MHz, CPLL: 666MHz and DPLL: 600MHz. >> >> Adjust all bus related OPPs to the values that are possible to derive from >> the top PLL configured by the bootloader. Also add a comment for each bus >> describing which PLL is used for it. >> >> The most significant change is the highest rate for wcore bus. It has been >> increased to 532MHz as this is the value configured initially by the >> bootloader. Also the voltage for this OPP is changed to match the value >> set by the bootloader. >> >> This patch finally allows the buses to operate on the rates matching the >> values set for each OPP and fixes the following warnings observed on boot: >> >> exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz) >> exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz) >> exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz) >> ... >> exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34) >> exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34) >> exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34) >> >> The problem with setting incorrect (in some cases much lower) clock rate >> for the defined OPP were there from the beginning, but went unnoticed >> because the only way to observe it was to manually check the rate of the >> respective clocks. The commit 4294a779bd8d ("PM / devfreq: exynos-bus: >> Convert to use dev_pm_opp_set_rate()") finally revealed it, because it >> enabled use of the generic code from the OPP framework, which issues the >> above mentioned warnings. >> >> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> >> --- >> arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 75 +++++++++++-------- >> 1 file changed, 45 insertions(+), 30 deletions(-) >> >> diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi >> index 663a38d53c9e..b6d6022e8735 100644 >> --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi >> +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi >> @@ -38,42 +38,44 @@ >> bus_wcore_opp_table: opp_table2 { >> compatible = "operating-points-v2"; >> >> + /* derived from 532MHz MPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <84000000>; >> + opp-hz = /bits/ 64 <88700000>; >> opp-microvolt = <925000 925000 1400000>; >> }; >> opp01 { >> - opp-hz = /bits/ 64 <111000000>; >> + opp-hz = /bits/ 64 <133000000>; >> opp-microvolt = <950000 950000 1400000>; >> }; >> opp02 { >> - opp-hz = /bits/ 64 <222000000>; >> + opp-hz = /bits/ 64 <177400000>; >> opp-microvolt = <950000 950000 1400000>; >> }; >> opp03 { >> - opp-hz = /bits/ 64 <333000000>; >> + opp-hz = /bits/ 64 <266000000>; >> opp-microvolt = <950000 950000 1400000>; >> }; >> opp04 { >> - opp-hz = /bits/ 64 <400000000>; >> - opp-microvolt = <987500 987500 1400000>; >> + opp-hz = /bits/ 64 <532000000>; >> + opp-microvolt = <1000000 1000000 1400000>; >> }; >> }; >> >> bus_noc_opp_table: opp_table3 { >> compatible = "operating-points-v2"; >> >> + /* derived from 666MHz CPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <67000000>; >> + opp-hz = /bits/ 64 <66600000>; >> }; >> opp01 { >> - opp-hz = /bits/ 64 <75000000>; >> + opp-hz = /bits/ 64 <74000000>; >> }; >> opp02 { >> - opp-hz = /bits/ 64 <86000000>; >> + opp-hz = /bits/ 64 <83250000>; >> }; >> opp03 { >> - opp-hz = /bits/ 64 <100000000>; >> + opp-hz = /bits/ 64 <111000000>; >> }; >> }; >> >> @@ -81,39 +83,42 @@ >> compatible = "operating-points-v2"; >> opp-shared; >> >> + /* derived from 666MHz CPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <100000000>; >> + opp-hz = /bits/ 64 <111000000>; >> }; >> opp01 { >> - opp-hz = /bits/ 64 <200000000>; >> + opp-hz = /bits/ 64 <222000000>; >> }; >> }; >> >> bus_fsys2_opp_table: opp_table5 { >> compatible = "operating-points-v2"; >> >> + /* derived from 600MHz DPLL */ >> opp00 { >> opp-hz = /bits/ 64 <75000000>; >> }; >> opp01 { >> - opp-hz = /bits/ 64 <100000000>; >> + opp-hz = /bits/ 64 <120000000>; >> }; >> opp02 { >> - opp-hz = /bits/ 64 <150000000>; >> + opp-hz = /bits/ 64 <200000000>; >> }; >> }; >> >> bus_mfc_opp_table: opp_table6 { >> compatible = "operating-points-v2"; >> >> + /* derived from 666MHz CPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <96000000>; >> + opp-hz = /bits/ 64 <83250000>; >> }; >> opp01 { >> opp-hz = /bits/ 64 <111000000>; >> }; >> opp02 { >> - opp-hz = /bits/ 64 <167000000>; >> + opp-hz = /bits/ 64 <166500000>; >> }; >> opp03 { >> opp-hz = /bits/ 64 <222000000>; >> @@ -126,8 +131,9 @@ >> bus_gen_opp_table: opp_table7 { >> compatible = "operating-points-v2"; >> >> + /* derived from 532MHz MPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <89000000>; >> + opp-hz = /bits/ 64 <88700000>; >> }; >> opp01 { >> opp-hz = /bits/ 64 <133000000>; >> @@ -136,32 +142,34 @@ >> opp-hz = /bits/ 64 <178000000>; >> }; >> opp03 { >> - opp-hz = /bits/ 64 <267000000>; >> + opp-hz = /bits/ 64 <266000000>; >> }; >> }; >> >> bus_peri_opp_table: opp_table8 { >> compatible = "operating-points-v2"; >> >> + /* derived from 666MHz CPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <67000000>; >> + opp-hz = /bits/ 64 <66600000>; >> }; >> }; >> >> bus_g2d_opp_table: opp_table9 { >> compatible = "operating-points-v2"; >> >> + /* derived from 666MHz CPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <84000000>; >> + opp-hz = /bits/ 64 <83250000>; >> }; >> opp01 { >> - opp-hz = /bits/ 64 <167000000>; >> + opp-hz = /bits/ 64 <111000000>; >> }; >> opp02 { >> - opp-hz = /bits/ 64 <222000000>; >> + opp-hz = /bits/ 64 <166500000>; >> }; >> opp03 { >> - opp-hz = /bits/ 64 <300000000>; >> + opp-hz = /bits/ 64 <222000000>; >> }; >> opp04 { >> opp-hz = /bits/ 64 <333000000>; >> @@ -171,8 +179,9 @@ >> bus_g2d_acp_opp_table: opp_table10 { >> compatible = "operating-points-v2"; >> >> + /* derived from 532MHz MPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <67000000>; >> + opp-hz = /bits/ 64 <66500000>; >> }; >> opp01 { >> opp-hz = /bits/ 64 <133000000>; >> @@ -181,13 +190,14 @@ >> opp-hz = /bits/ 64 <178000000>; >> }; >> opp03 { >> - opp-hz = /bits/ 64 <267000000>; >> + opp-hz = /bits/ 64 <266000000>; >> }; >> }; >> >> bus_jpeg_opp_table: opp_table11 { >> compatible = "operating-points-v2"; >> >> + /* derived from 600MHz DPLL */ >> opp00 { >> opp-hz = /bits/ 64 <75000000>; >> }; >> @@ -205,23 +215,25 @@ >> bus_jpeg_apb_opp_table: opp_table12 { >> compatible = "operating-points-v2"; >> >> + /* derived from 666MHz CPLL */ >> opp00 { >> - opp-hz = /bits/ 64 <84000000>; >> + opp-hz = /bits/ 64 <83250000>; >> }; >> opp01 { >> opp-hz = /bits/ 64 <111000000>; >> }; >> opp02 { >> - opp-hz = /bits/ 64 <134000000>; >> + opp-hz = /bits/ 64 <133000000>; >> }; >> opp03 { >> - opp-hz = /bits/ 64 <167000000>; >> + opp-hz = /bits/ 64 <166500000>; >> }; >> }; >> >> bus_disp1_fimd_opp_table: opp_table13 { >> compatible = "operating-points-v2"; >> >> + /* derived from 600MHz DPLL */ >> opp00 { >> opp-hz = /bits/ 64 <120000000>; >> }; >> @@ -233,6 +245,7 @@ >> bus_disp1_opp_table: opp_table14 { >> compatible = "operating-points-v2"; >> >> + /* derived from 600MHz DPLL */ >> opp00 { >> opp-hz = /bits/ 64 <120000000>; >> }; >> @@ -247,6 +260,7 @@ >> bus_gscl_opp_table: opp_table15 { >> compatible = "operating-points-v2"; >> >> + /* derived from 600MHz DPLL */ >> opp00 { >> opp-hz = /bits/ 64 <150000000>; >> }; >> @@ -261,6 +275,7 @@ >> bus_mscl_opp_table: opp_table16 { >> compatible = "operating-points-v2"; >> >> + /* derived from 666MHz CPLL */ >> opp00 { >> opp-hz = /bits/ 64 <84000000>; >> }; >> @@ -274,7 +289,7 @@ >> opp-hz = /bits/ 64 <333000000>; >> }; >> opp04 { >> - opp-hz = /bits/ 64 <400000000>; >> + opp-hz = /bits/ 64 <666000000>; >> }; >> }; >> >> @@ -398,7 +413,7 @@ >> }; >> >> &bus_fsys { >> - operating-points-v2 = <&bus_fsys_apb_opp_table>; >> + operating-points-v2 = <&bus_fsys2_opp_table>; > > Need to remove 'opp-shared' property in bus_fsys_apb_opp_table. > And need to add 'opp-shared' property to bus_fsys2_opp_table. I've checked the dt bindings and I think that opp-shared property has to be removed at all. Clocks between fsys and fsys2 buses are not related and regulator is currently already handled by in a different way by the passive governor. >> devfreq = <&bus_wcore>; >> status = "okay"; >> }; >> > If you fix the things related to 'opp-shared', Looks good to me. > Tested-by: Chanwoo Choi <cw00.choi@samsung.com> > Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> > Best regards
On 12/19/19 6:09 PM, Marek Szyprowski wrote: > Hi Chanwoo, > > On 19.12.2019 10:07, Chanwoo Choi wrote: >> On 12/19/19 5:29 PM, Marek Szyprowski wrote: >>> Hardkernel's Odroid XU3/XU4/HC1 boards use bootloader, which configures top >>> PLLs to the following values: MPLL: 532MHz, CPLL: 666MHz and DPLL: 600MHz. >>> >>> Adjust all bus related OPPs to the values that are possible to derive from >>> the top PLL configured by the bootloader. Also add a comment for each bus >>> describing which PLL is used for it. >>> >>> The most significant change is the highest rate for wcore bus. It has been >>> increased to 532MHz as this is the value configured initially by the >>> bootloader. Also the voltage for this OPP is changed to match the value >>> set by the bootloader. >>> >>> This patch finally allows the buses to operate on the rates matching the >>> values set for each OPP and fixes the following warnings observed on boot: >>> >>> exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz) >>> exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz) >>> exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz) >>> ... >>> exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34) >>> exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34) >>> exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34) >>> >>> The problem with setting incorrect (in some cases much lower) clock rate >>> for the defined OPP were there from the beginning, but went unnoticed >>> because the only way to observe it was to manually check the rate of the >>> respective clocks. The commit 4294a779bd8d ("PM / devfreq: exynos-bus: >>> Convert to use dev_pm_opp_set_rate()") finally revealed it, because it >>> enabled use of the generic code from the OPP framework, which issues the >>> above mentioned warnings. >>> >>> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> >>> --- >>> arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 75 +++++++++++-------- >>> 1 file changed, 45 insertions(+), 30 deletions(-) >>> >>> diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi >>> index 663a38d53c9e..b6d6022e8735 100644 >>> --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi >>> +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi >>> @@ -38,42 +38,44 @@ >>> bus_wcore_opp_table: opp_table2 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 532MHz MPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <84000000>; >>> + opp-hz = /bits/ 64 <88700000>; >>> opp-microvolt = <925000 925000 1400000>; >>> }; >>> opp01 { >>> - opp-hz = /bits/ 64 <111000000>; >>> + opp-hz = /bits/ 64 <133000000>; >>> opp-microvolt = <950000 950000 1400000>; >>> }; >>> opp02 { >>> - opp-hz = /bits/ 64 <222000000>; >>> + opp-hz = /bits/ 64 <177400000>; >>> opp-microvolt = <950000 950000 1400000>; >>> }; >>> opp03 { >>> - opp-hz = /bits/ 64 <333000000>; >>> + opp-hz = /bits/ 64 <266000000>; >>> opp-microvolt = <950000 950000 1400000>; >>> }; >>> opp04 { >>> - opp-hz = /bits/ 64 <400000000>; >>> - opp-microvolt = <987500 987500 1400000>; >>> + opp-hz = /bits/ 64 <532000000>; >>> + opp-microvolt = <1000000 1000000 1400000>; >>> }; >>> }; >>> >>> bus_noc_opp_table: opp_table3 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 666MHz CPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <67000000>; >>> + opp-hz = /bits/ 64 <66600000>; >>> }; >>> opp01 { >>> - opp-hz = /bits/ 64 <75000000>; >>> + opp-hz = /bits/ 64 <74000000>; >>> }; >>> opp02 { >>> - opp-hz = /bits/ 64 <86000000>; >>> + opp-hz = /bits/ 64 <83250000>; >>> }; >>> opp03 { >>> - opp-hz = /bits/ 64 <100000000>; >>> + opp-hz = /bits/ 64 <111000000>; >>> }; >>> }; >>> >>> @@ -81,39 +83,42 @@ >>> compatible = "operating-points-v2"; >>> opp-shared; >>> >>> + /* derived from 666MHz CPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <100000000>; >>> + opp-hz = /bits/ 64 <111000000>; >>> }; >>> opp01 { >>> - opp-hz = /bits/ 64 <200000000>; >>> + opp-hz = /bits/ 64 <222000000>; >>> }; >>> }; >>> >>> bus_fsys2_opp_table: opp_table5 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 600MHz DPLL */ >>> opp00 { >>> opp-hz = /bits/ 64 <75000000>; >>> }; >>> opp01 { >>> - opp-hz = /bits/ 64 <100000000>; >>> + opp-hz = /bits/ 64 <120000000>; >>> }; >>> opp02 { >>> - opp-hz = /bits/ 64 <150000000>; >>> + opp-hz = /bits/ 64 <200000000>; >>> }; >>> }; >>> >>> bus_mfc_opp_table: opp_table6 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 666MHz CPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <96000000>; >>> + opp-hz = /bits/ 64 <83250000>; >>> }; >>> opp01 { >>> opp-hz = /bits/ 64 <111000000>; >>> }; >>> opp02 { >>> - opp-hz = /bits/ 64 <167000000>; >>> + opp-hz = /bits/ 64 <166500000>; >>> }; >>> opp03 { >>> opp-hz = /bits/ 64 <222000000>; >>> @@ -126,8 +131,9 @@ >>> bus_gen_opp_table: opp_table7 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 532MHz MPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <89000000>; >>> + opp-hz = /bits/ 64 <88700000>; >>> }; >>> opp01 { >>> opp-hz = /bits/ 64 <133000000>; >>> @@ -136,32 +142,34 @@ >>> opp-hz = /bits/ 64 <178000000>; >>> }; >>> opp03 { >>> - opp-hz = /bits/ 64 <267000000>; >>> + opp-hz = /bits/ 64 <266000000>; >>> }; >>> }; >>> >>> bus_peri_opp_table: opp_table8 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 666MHz CPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <67000000>; >>> + opp-hz = /bits/ 64 <66600000>; >>> }; >>> }; >>> >>> bus_g2d_opp_table: opp_table9 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 666MHz CPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <84000000>; >>> + opp-hz = /bits/ 64 <83250000>; >>> }; >>> opp01 { >>> - opp-hz = /bits/ 64 <167000000>; >>> + opp-hz = /bits/ 64 <111000000>; >>> }; >>> opp02 { >>> - opp-hz = /bits/ 64 <222000000>; >>> + opp-hz = /bits/ 64 <166500000>; >>> }; >>> opp03 { >>> - opp-hz = /bits/ 64 <300000000>; >>> + opp-hz = /bits/ 64 <222000000>; >>> }; >>> opp04 { >>> opp-hz = /bits/ 64 <333000000>; >>> @@ -171,8 +179,9 @@ >>> bus_g2d_acp_opp_table: opp_table10 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 532MHz MPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <67000000>; >>> + opp-hz = /bits/ 64 <66500000>; >>> }; >>> opp01 { >>> opp-hz = /bits/ 64 <133000000>; >>> @@ -181,13 +190,14 @@ >>> opp-hz = /bits/ 64 <178000000>; >>> }; >>> opp03 { >>> - opp-hz = /bits/ 64 <267000000>; >>> + opp-hz = /bits/ 64 <266000000>; >>> }; >>> }; >>> >>> bus_jpeg_opp_table: opp_table11 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 600MHz DPLL */ >>> opp00 { >>> opp-hz = /bits/ 64 <75000000>; >>> }; >>> @@ -205,23 +215,25 @@ >>> bus_jpeg_apb_opp_table: opp_table12 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 666MHz CPLL */ >>> opp00 { >>> - opp-hz = /bits/ 64 <84000000>; >>> + opp-hz = /bits/ 64 <83250000>; >>> }; >>> opp01 { >>> opp-hz = /bits/ 64 <111000000>; >>> }; >>> opp02 { >>> - opp-hz = /bits/ 64 <134000000>; >>> + opp-hz = /bits/ 64 <133000000>; >>> }; >>> opp03 { >>> - opp-hz = /bits/ 64 <167000000>; >>> + opp-hz = /bits/ 64 <166500000>; >>> }; >>> }; >>> >>> bus_disp1_fimd_opp_table: opp_table13 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 600MHz DPLL */ >>> opp00 { >>> opp-hz = /bits/ 64 <120000000>; >>> }; >>> @@ -233,6 +245,7 @@ >>> bus_disp1_opp_table: opp_table14 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 600MHz DPLL */ >>> opp00 { >>> opp-hz = /bits/ 64 <120000000>; >>> }; >>> @@ -247,6 +260,7 @@ >>> bus_gscl_opp_table: opp_table15 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 600MHz DPLL */ >>> opp00 { >>> opp-hz = /bits/ 64 <150000000>; >>> }; >>> @@ -261,6 +275,7 @@ >>> bus_mscl_opp_table: opp_table16 { >>> compatible = "operating-points-v2"; >>> >>> + /* derived from 666MHz CPLL */ >>> opp00 { >>> opp-hz = /bits/ 64 <84000000>; >>> }; >>> @@ -274,7 +289,7 @@ >>> opp-hz = /bits/ 64 <333000000>; >>> }; >>> opp04 { >>> - opp-hz = /bits/ 64 <400000000>; >>> + opp-hz = /bits/ 64 <666000000>; >>> }; >>> }; >>> >>> @@ -398,7 +413,7 @@ >>> }; >>> >>> &bus_fsys { >>> - operating-points-v2 = <&bus_fsys_apb_opp_table>; >>> + operating-points-v2 = <&bus_fsys2_opp_table>; >> >> Need to remove 'opp-shared' property in bus_fsys_apb_opp_table. >> And need to add 'opp-shared' property to bus_fsys2_opp_table. > > I've checked the dt bindings and I think that opp-shared property has to > be removed at all. Clocks between fsys and fsys2 buses are not related > and regulator is currently already handled by in a different way by the > passive governor. You're right. I realized 'opp-shared' is not necessary by reading Documentation/devicetree/bindings/opp/opp.txt. Thanks. > >>> devfreq = <&bus_wcore>; >>> status = "okay"; >>> }; >>> >> If you fix the things related to 'opp-shared', Looks good to me. >> Tested-by: Chanwoo Choi <cw00.choi@samsung.com> >> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> >> > Best regards >
diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi index 663a38d53c9e..b6d6022e8735 100644 --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi @@ -38,42 +38,44 @@ bus_wcore_opp_table: opp_table2 { compatible = "operating-points-v2"; + /* derived from 532MHz MPLL */ opp00 { - opp-hz = /bits/ 64 <84000000>; + opp-hz = /bits/ 64 <88700000>; opp-microvolt = <925000 925000 1400000>; }; opp01 { - opp-hz = /bits/ 64 <111000000>; + opp-hz = /bits/ 64 <133000000>; opp-microvolt = <950000 950000 1400000>; }; opp02 { - opp-hz = /bits/ 64 <222000000>; + opp-hz = /bits/ 64 <177400000>; opp-microvolt = <950000 950000 1400000>; }; opp03 { - opp-hz = /bits/ 64 <333000000>; + opp-hz = /bits/ 64 <266000000>; opp-microvolt = <950000 950000 1400000>; }; opp04 { - opp-hz = /bits/ 64 <400000000>; - opp-microvolt = <987500 987500 1400000>; + opp-hz = /bits/ 64 <532000000>; + opp-microvolt = <1000000 1000000 1400000>; }; }; bus_noc_opp_table: opp_table3 { compatible = "operating-points-v2"; + /* derived from 666MHz CPLL */ opp00 { - opp-hz = /bits/ 64 <67000000>; + opp-hz = /bits/ 64 <66600000>; }; opp01 { - opp-hz = /bits/ 64 <75000000>; + opp-hz = /bits/ 64 <74000000>; }; opp02 { - opp-hz = /bits/ 64 <86000000>; + opp-hz = /bits/ 64 <83250000>; }; opp03 { - opp-hz = /bits/ 64 <100000000>; + opp-hz = /bits/ 64 <111000000>; }; }; @@ -81,39 +83,42 @@ compatible = "operating-points-v2"; opp-shared; + /* derived from 666MHz CPLL */ opp00 { - opp-hz = /bits/ 64 <100000000>; + opp-hz = /bits/ 64 <111000000>; }; opp01 { - opp-hz = /bits/ 64 <200000000>; + opp-hz = /bits/ 64 <222000000>; }; }; bus_fsys2_opp_table: opp_table5 { compatible = "operating-points-v2"; + /* derived from 600MHz DPLL */ opp00 { opp-hz = /bits/ 64 <75000000>; }; opp01 { - opp-hz = /bits/ 64 <100000000>; + opp-hz = /bits/ 64 <120000000>; }; opp02 { - opp-hz = /bits/ 64 <150000000>; + opp-hz = /bits/ 64 <200000000>; }; }; bus_mfc_opp_table: opp_table6 { compatible = "operating-points-v2"; + /* derived from 666MHz CPLL */ opp00 { - opp-hz = /bits/ 64 <96000000>; + opp-hz = /bits/ 64 <83250000>; }; opp01 { opp-hz = /bits/ 64 <111000000>; }; opp02 { - opp-hz = /bits/ 64 <167000000>; + opp-hz = /bits/ 64 <166500000>; }; opp03 { opp-hz = /bits/ 64 <222000000>; @@ -126,8 +131,9 @@ bus_gen_opp_table: opp_table7 { compatible = "operating-points-v2"; + /* derived from 532MHz MPLL */ opp00 { - opp-hz = /bits/ 64 <89000000>; + opp-hz = /bits/ 64 <88700000>; }; opp01 { opp-hz = /bits/ 64 <133000000>; @@ -136,32 +142,34 @@ opp-hz = /bits/ 64 <178000000>; }; opp03 { - opp-hz = /bits/ 64 <267000000>; + opp-hz = /bits/ 64 <266000000>; }; }; bus_peri_opp_table: opp_table8 { compatible = "operating-points-v2"; + /* derived from 666MHz CPLL */ opp00 { - opp-hz = /bits/ 64 <67000000>; + opp-hz = /bits/ 64 <66600000>; }; }; bus_g2d_opp_table: opp_table9 { compatible = "operating-points-v2"; + /* derived from 666MHz CPLL */ opp00 { - opp-hz = /bits/ 64 <84000000>; + opp-hz = /bits/ 64 <83250000>; }; opp01 { - opp-hz = /bits/ 64 <167000000>; + opp-hz = /bits/ 64 <111000000>; }; opp02 { - opp-hz = /bits/ 64 <222000000>; + opp-hz = /bits/ 64 <166500000>; }; opp03 { - opp-hz = /bits/ 64 <300000000>; + opp-hz = /bits/ 64 <222000000>; }; opp04 { opp-hz = /bits/ 64 <333000000>; @@ -171,8 +179,9 @@ bus_g2d_acp_opp_table: opp_table10 { compatible = "operating-points-v2"; + /* derived from 532MHz MPLL */ opp00 { - opp-hz = /bits/ 64 <67000000>; + opp-hz = /bits/ 64 <66500000>; }; opp01 { opp-hz = /bits/ 64 <133000000>; @@ -181,13 +190,14 @@ opp-hz = /bits/ 64 <178000000>; }; opp03 { - opp-hz = /bits/ 64 <267000000>; + opp-hz = /bits/ 64 <266000000>; }; }; bus_jpeg_opp_table: opp_table11 { compatible = "operating-points-v2"; + /* derived from 600MHz DPLL */ opp00 { opp-hz = /bits/ 64 <75000000>; }; @@ -205,23 +215,25 @@ bus_jpeg_apb_opp_table: opp_table12 { compatible = "operating-points-v2"; + /* derived from 666MHz CPLL */ opp00 { - opp-hz = /bits/ 64 <84000000>; + opp-hz = /bits/ 64 <83250000>; }; opp01 { opp-hz = /bits/ 64 <111000000>; }; opp02 { - opp-hz = /bits/ 64 <134000000>; + opp-hz = /bits/ 64 <133000000>; }; opp03 { - opp-hz = /bits/ 64 <167000000>; + opp-hz = /bits/ 64 <166500000>; }; }; bus_disp1_fimd_opp_table: opp_table13 { compatible = "operating-points-v2"; + /* derived from 600MHz DPLL */ opp00 { opp-hz = /bits/ 64 <120000000>; }; @@ -233,6 +245,7 @@ bus_disp1_opp_table: opp_table14 { compatible = "operating-points-v2"; + /* derived from 600MHz DPLL */ opp00 { opp-hz = /bits/ 64 <120000000>; }; @@ -247,6 +260,7 @@ bus_gscl_opp_table: opp_table15 { compatible = "operating-points-v2"; + /* derived from 600MHz DPLL */ opp00 { opp-hz = /bits/ 64 <150000000>; }; @@ -261,6 +275,7 @@ bus_mscl_opp_table: opp_table16 { compatible = "operating-points-v2"; + /* derived from 666MHz CPLL */ opp00 { opp-hz = /bits/ 64 <84000000>; }; @@ -274,7 +289,7 @@ opp-hz = /bits/ 64 <333000000>; }; opp04 { - opp-hz = /bits/ 64 <400000000>; + opp-hz = /bits/ 64 <666000000>; }; }; @@ -398,7 +413,7 @@ }; &bus_fsys { - operating-points-v2 = <&bus_fsys_apb_opp_table>; + operating-points-v2 = <&bus_fsys2_opp_table>; devfreq = <&bus_wcore>; status = "okay"; };
Hardkernel's Odroid XU3/XU4/HC1 boards use bootloader, which configures top PLLs to the following values: MPLL: 532MHz, CPLL: 666MHz and DPLL: 600MHz. Adjust all bus related OPPs to the values that are possible to derive from the top PLL configured by the bootloader. Also add a comment for each bus describing which PLL is used for it. The most significant change is the highest rate for wcore bus. It has been increased to 532MHz as this is the value configured initially by the bootloader. Also the voltage for this OPP is changed to match the value set by the bootloader. This patch finally allows the buses to operate on the rates matching the values set for each OPP and fixes the following warnings observed on boot: exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz) exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz) exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz) ... exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34) exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34) exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34) The problem with setting incorrect (in some cases much lower) clock rate for the defined OPP were there from the beginning, but went unnoticed because the only way to observe it was to manually check the rate of the respective clocks. The commit 4294a779bd8d ("PM / devfreq: exynos-bus: Convert to use dev_pm_opp_set_rate()") finally revealed it, because it enabled use of the generic code from the OPP framework, which issues the above mentioned warnings. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> --- arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 75 +++++++++++-------- 1 file changed, 45 insertions(+), 30 deletions(-)