new file mode 100644
@@ -0,0 +1,169 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/supply/qcom,pm8941-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Switch-Mode Battery Charger and Boost
+
+maintainers:
+ - Sebastian Reichel <sre@kernel.org>
+
+properties:
+ compatible:
+ const: qcom,pm8941-charger
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: charge done
+ - description: charge fast mode
+ - description: charge trickle mode
+ - description: battery temperature ok
+ - description: battery present
+ - description: charger disconnected
+ - description: USB-in valid
+ - description: DC-in valid
+
+ interrupt-names:
+ items:
+ - const: chg-done
+ - const: chg-fast
+ - const: chg-trkl
+ - const: bat-temp-ok
+ - const: bat-present
+ - const: chg-gone
+ - const: usb-valid
+ - const: dc-valid
+
+ qcom,fast-charge-current-limit:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 100000
+ maximum: 3000000
+ description: Maximum charge current in uA; May be clamped to safety limits; Defaults to 1A
+
+ qcom,fast-charge-low-threshold-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 2100000
+ maximum: 3600000
+ description: |
+ Battery voltage limit in uV above which fast charging may operate; Defaults to 3.2V
+ Below this value linear or switch-mode auto-trickle-charging will operate.
+
+ qcom,fast-charge-high-threshold-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 3240000
+ maximum: 5000000
+ description: |
+ Battery voltage limit in uV below which fast charging may operate; Defaults to 4.2V
+ The fast charger will attempt to charge the battery to this voltage.
+ May be clamped to safety limits.
+
+ qcom,fast-charge-safe-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 3240000
+ maximum: 5000000
+ description: |
+ Maximum safe battery voltage in uV; May be pre-set by bootloader, in which case,
+ setting this will harmlessly fail. The property 'fast-charge-high-watermark' will
+ be clamped by this value. Defaults to 4.2V.
+
+ qcom,fast-charge-safe-current:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 100000
+ maximum: 3000000
+ description: |
+ Maximum safe battery charge current in uA; May pre-set by bootloader, in which case,
+ setting this will harmlessly fail. The property 'qcom,fast-charge-current-limit'
+ will be clamped by this value. Defaults to 1A.
+
+ qcom,auto-recharge-threshold-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 3240000
+ maximum: 5000000
+ description: |
+ Battery voltage limit in uV below which auto-recharge functionality will restart charging
+ after end-of-charge; The high cutoff limit for auto-recharge is 5% above this value.
+ Defaults to 4.1V.
+
+ qcom,minimum-input-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 4200000
+ maximum: 9600000
+ description: |
+ Input voltage level in uV above which charging may operate. Defaults to 4.3V.
+
+ qcom,dc-current-limit:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 100000
+ maximum: 2500000
+ description: |
+ Default DC charge current limit in uA. Defaults to 100mA.
+
+ qcom,disable-dc:
+ type: boolean
+ description: Disable DC charger
+
+ qcom,jeita-extended-temp-range:
+ type: boolean
+ description: |
+ Enable JEITA extended temperature range; This does *not* adjust the maximum charge
+ voltage or current in the extended temperature range. It only allows charging when
+ the battery is in the extended temperature range. Voltage/current regulation must
+ be done externally to fully comply with the JEITA safety guidelines if this flag
+ is set.
+
+ usb-otg-in-supply:
+ description: Reference to the regulator supplying power to the USB_OTG_IN pin.
+
+ otg-vbus:
+ type: object
+ description: |
+ This node defines a regulator used to control the direction of VBUS voltage.
+ Specifically whether to supply voltage to VBUS for host mode operation of the OTG port,
+ or allow input voltage from external VBUS for charging. In the hardware, the supply for
+ this regulator comes from usb_otg_in-supply.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ pmic {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@1000 {
+ compatible = "qcom,pm8941-charger";
+ reg = <0x1000>;
+ interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+ interrupt-names = "chg-done",
+ "chg-fast",
+ "chg-trkl",
+ "bat-temp-ok",
+ "bat-present",
+ "chg-gone",
+ "usb-valid",
+ "dc-valid";
+ qcom,fast-charge-current-limit = <1000000>;
+ qcom,dc-current-limit = <1000000>;
+ usb-otg-in-supply = <&pm8941_5vs1>;
+
+ otg-vbus {};
+ };
+ };
deleted file mode 100644
@@ -1,150 +0,0 @@
-Qualcomm Switch-Mode Battery Charger and Boost
-
-PROPERTIES
-- compatible:
- Usage: required
- Value type: <stringlist>
- Description: Must be one of:
- - "qcom,pm8941-charger"
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Description: Base address of registers for SMBB block
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Description: The format of the specifier is defined by the binding document
- describing the node's interrupt parent. Must contain one
- specifier for each of the following interrupts, in order:
- - charge done
- - charge fast mode
- - charge trickle mode
- - battery temperature ok
- - battery present
- - charger disconnected
- - USB-in valid
- - DC-in valid
-
-- interrupt-names:
- Usage: required
- Value type: <stringlist>
- Description: Must contain the following list, strictly ordered:
- "chg-done",
- "chg-fast",
- "chg-trkl",
- "bat-temp-ok",
- "bat-present",
- "chg-gone",
- "usb-valid",
- "dc-valid"
-
-- qcom,fast-charge-current-limit:
- Usage: optional (default: 1A, or pre-configured value)
- Value type: <u32>; uA; range [100mA : 3A]
- Description: Maximum charge current; May be clamped to safety limits.
-
-- qcom,fast-charge-low-threshold-voltage:
- Usage: optional (default: 3.2V, or pre-configured value)
- Value type: <u32>; uV; range [2.1V : 3.6V]
- Description: Battery voltage limit above which fast charging may operate;
- Below this value linear or switch-mode auto-trickle-charging
- will operate.
-
-- qcom,fast-charge-high-threshold-voltage:
- Usage: optional (default: 4.2V, or pre-configured value)
- Value type: <u32>; uV; range [3.24V : 5V]
- Description: Battery voltage limit below which fast charging may operate;
- The fast charger will attempt to charge the battery to this
- voltage. May be clamped to safety limits.
-
-- qcom,fast-charge-safe-voltage:
- Usage: optional (default: 4.2V, or pre-configured value)
- Value type: <u32>; uV; range [3.24V : 5V]
- Description: Maximum safe battery voltage; May be pre-set by bootloader, in
- which case, setting this will harmlessly fail. The property
- 'fast-charge-high-watermark' will be clamped by this value.
-
-- qcom,fast-charge-safe-current:
- Usage: optional (default: 1A, or pre-configured value)
- Value type: <u32>; uA; range [100mA : 3A]
- Description: Maximum safe battery charge current; May pre-set by bootloader,
- in which case, setting this will harmlessly fail. The property
- 'qcom,fast-charge-current-limit' will be clamped by this value.
-
-- qcom,auto-recharge-threshold-voltage:
- Usage: optional (default: 4.1V, or pre-configured value)
- Value type: <u32>; uV; range [3.24V : 5V]
- Description: Battery voltage limit below which auto-recharge functionality
- will restart charging after end-of-charge; The high cutoff
- limit for auto-recharge is 5% above this value.
-
-- qcom,minimum-input-voltage:
- Usage: optional (default: 4.3V, or pre-configured value)
- Value type: <u32>; uV; range [4.2V : 9.6V]
- Description: Input voltage level above which charging may operate
-
-- qcom,dc-current-limit:
- Usage: optional (default: 100mA, or pre-configured value)
- Value type: <u32>; uA; range [100mA : 2.5A]
- Description: Default DC charge current limit
-
-- qcom,disable-dc:
- Usage: optional (default: false)
- Value type: boolean: <u32> or <empty>
- Description: Disable DC charger
-
-- qcom,jeita-extended-temp-range:
- Usage: optional (default: false)
- Value type: boolean: <u32> or <empty>
- Description: Enable JEITA extended temperature range; This does *not*
- adjust the maximum charge voltage or current in the extended
- temperature range. It only allows charging when the battery
- is in the extended temperature range. Voltage/current
- regulation must be done externally to fully comply with
- the JEITA safety guidelines if this flag is set.
-
-- usb_otg_in-supply:
- Usage: optional
- Value type: <phandle>
- Description: Reference to the regulator supplying power to the USB_OTG_IN
- pin.
-
-child nodes:
-- otg-vbus:
- Usage: optional
- Description: This node defines a regulator used to control the direction
- of VBUS voltage - specifically: whether to supply voltage
- to VBUS for host mode operation of the OTG port, or allow
- input voltage from external VBUS for charging. In the
- hardware, the supply for this regulator comes from
- usb_otg_in-supply.
-
-EXAMPLE
-charger@1000 {
- compatible = "qcom,pm8941-charger";
- reg = <0x1000 0x700>;
- interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
- interrupt-names = "chg-done",
- "chg-fast",
- "chg-trkl",
- "bat-temp-ok",
- "bat-present",
- "chg-gone",
- "usb-valid",
- "dc-valid";
-
- qcom,fast-charge-current-limit = <1000000>;
- qcom,dc-charge-current-limit = <1000000>;
- usb_otg_in-supply = <&pm8941_5vs1>;
-
- otg-vbus {};
-};
Convert the binding to DT schema format. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> --- .../power/supply/qcom,pm8941-charger.yaml | 169 ++++++++++++++++++ .../bindings/power/supply/qcom_smbb.txt | 150 ---------------- 2 files changed, 169 insertions(+), 150 deletions(-) create mode 100644 Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml delete mode 100644 Documentation/devicetree/bindings/power/supply/qcom_smbb.txt