[v4,08/10] soc: qcom: cpr3: Add IPQ9574 definitions

Commit Message

Varadarajan Narayanan July 3, 2024, 9:16 a.m. UTC

From: Praveenkumar I <[e-mail]>

* Add thread, scaling factor, CPR descriptor defines to enable
  CPR on IPQ9574.

* Skip 'acc' usage since IPQ9574 does not have acc

Signed-off-by: Praveenkumar I <[e-mail]>
Signed-off-by: Varadarajan Narayanan <[e-mail]>
---
v4: s/silver//, s/cprh/cpr4/
    Skip 'acc' related code as IPQ9574 does not have acc

v3: Fix patch author
    Included below information in cover letter
v2: Fix Signed-off-by order
Depends:
	[1] https://lore.kernel.org/lkml/[e-mail]/T/
	[2] https://github.com/quic-varada/cpr/commits/konrad/
---
 drivers/pmdomain/qcom/cpr3.c | 143 ++++++++++++++++++++++++++++++++++-
 1 file changed, 141 insertions(+), 2 deletions(-)

Comments

Dmitry Baryshkov July 3, 2024, 10:49 a.m. UTC | #1

On Wed, Jul 03, 2024 at 02:46:49PM GMT, Varadarajan Narayanan wrote:
> From: Praveenkumar I <[e-mail]>
> 
> * Add thread, scaling factor, CPR descriptor defines to enable
>   CPR on IPQ9574.
> 
> * Skip 'acc' usage since IPQ9574 does not have acc
> 
> Signed-off-by: Praveenkumar I <[e-mail]>
> Signed-off-by: Varadarajan Narayanan <[e-mail]>
> ---
> v4: s/silver//, s/cprh/cpr4/
>     Skip 'acc' related code as IPQ9574 does not have acc
> 
> v3: Fix patch author
>     Included below information in cover letter
> v2: Fix Signed-off-by order
> Depends:
> 	[1] https://lore.kernel.org/lkml/[e-mail]/T/
> 	[2] https://github.com/quic-varada/cpr/commits/konrad/
> ---
>  drivers/pmdomain/qcom/cpr3.c | 143 ++++++++++++++++++++++++++++++++++-
>  1 file changed, 141 insertions(+), 2 deletions(-)
> 



> @@ -2703,7 +2840,8 @@ static int cpr_probe(struct platform_device *pdev)
>  
>  	mutex_init(&drv->lock);
>  
> -	if (desc->cpr_type < CTRL_TYPE_CPRH) {
> +	if (desc->cpr_type < CTRL_TYPE_CPRH &&
> +	    !of_device_is_compatible(dev->of_node, "qcom,ipq9574-cpr4")) {

No. Check for ->acc_desc instead.

>  		np = of_parse_phandle(dev->of_node, "qcom,acc", 0);
>  		if (!np)
>  			return -ENODEV;
> @@ -2828,6 +2966,7 @@ static void cpr_remove(struct platform_device *pdev)
>  }
>  
>  static const struct of_device_id cpr3_match_table[] = {
> +	{ .compatible = "qcom,ipq9574-cpr4", .data = &ipq9574_cpr_acc_desc },
>  	{ .compatible = "qcom,msm8998-cprh", .data = &msm8998_cpr_acc_desc },
>  	{ .compatible = "qcom,sdm630-cprh", .data = &sdm630_cpr_acc_desc },
>  	{ }
> -- 
> 2.34.1
>

Varadarajan Narayanan July 4, 2024, 5:02 a.m. UTC | #2

On Wed, Jul 03, 2024 at 01:49:15PM +0300, Dmitry Baryshkov wrote:
> On Wed, Jul 03, 2024 at 02:46:49PM GMT, Varadarajan Narayanan wrote:
> > From: Praveenkumar I <[e-mail]>
> >
> > * Add thread, scaling factor, CPR descriptor defines to enable
> >   CPR on IPQ9574.
> >
> > * Skip 'acc' usage since IPQ9574 does not have acc
> >
> > Signed-off-by: Praveenkumar I <[e-mail]>
> > Signed-off-by: Varadarajan Narayanan <[e-mail]>
> > ---
> > v4: s/silver//, s/cprh/cpr4/
> >     Skip 'acc' related code as IPQ9574 does not have acc
> >
> > v3: Fix patch author
> >     Included below information in cover letter
> > v2: Fix Signed-off-by order
> > Depends:
> > 	[1] https://lore.kernel.org/lkml/[e-mail]/T/
> > 	[2] https://github.com/quic-varada/cpr/commits/konrad/
> > ---
> >  drivers/pmdomain/qcom/cpr3.c | 143 ++++++++++++++++++++++++++++++++++-
> >  1 file changed, 141 insertions(+), 2 deletions(-)
> >
>
>
>
> > @@ -2703,7 +2840,8 @@ static int cpr_probe(struct platform_device *pdev)
> >
> >  	mutex_init(&drv->lock);
> >
> > -	if (desc->cpr_type < CTRL_TYPE_CPRH) {
> > +	if (desc->cpr_type < CTRL_TYPE_CPRH &&
> > +	    !of_device_is_compatible(dev->of_node, "qcom,ipq9574-cpr4")) {
>
> No. Check for ->acc_desc instead.

Ok.

Thanks
Varada

> >  		np = of_parse_phandle(dev->of_node, "qcom,acc", 0);
> >  		if (!np)
> >  			return -ENODEV;
> > @@ -2828,6 +2966,7 @@ static void cpr_remove(struct platform_device *pdev)
> >  }
> >
> >  static const struct of_device_id cpr3_match_table[] = {
> > +	{ .compatible = "qcom,ipq9574-cpr4", .data = &ipq9574_cpr_acc_desc },
> >  	{ .compatible = "qcom,msm8998-cprh", .data = &msm8998_cpr_acc_desc },
> >  	{ .compatible = "qcom,sdm630-cprh", .data = &sdm630_cpr_acc_desc },
> >  	{ }
> > --
> > 2.34.1
> >
>
> --
> With best wishes
> Dmitry

Patch

diff --git a/drivers/pmdomain/qcom/cpr3.c b/drivers/pmdomain/qcom/cpr3.c
index 6ceb7605f84d..abd890cc4d9e 100644
--- a/drivers/pmdomain/qcom/cpr3.c
+++ b/drivers/pmdomain/qcom/cpr3.c
@@ -2056,6 +2056,142 @@  static const struct cpr_acc_desc msm8998_cpr_acc_desc = {
 	.cpr_desc = &msm8998_cpr_desc,
 };
 
+static const int ipq9574_scaling_factor[][CPR3_RO_COUNT] = {
+	/* Fuse Corner 0 */
+	{
+		2383, 2112, 2250, 1502, 2269, 2055, 2046, 1949,
+		2128, 1945, 2282, 2061, 2010, 2216, 2054, 2332
+	},
+	/* Fuse Corner 1 */
+	{
+		2383, 2112, 2250, 1502, 2269, 2055, 2046, 1949,
+		2128, 1945, 2282, 2061, 2010, 2216, 2054, 2332
+	},
+	/* Fuse Corner 2 */
+	{
+		2383, 2112, 2250, 1502, 2269, 2055, 2046, 1949,
+		2128, 1945, 2282, 2061, 2010, 2216, 2054, 2332
+	},
+	/* Fuse Corner 3 */
+	{
+		2383, 2112, 2250, 1502, 2269, 2055, 2046, 1949,
+		2128, 1945, 2282, 2061, 2010, 2216, 2054, 2332
+	},
+};
+
+static const struct cpr_thread_desc ipq9574_thread = {
+	.controller_id = 0,
+	.hw_tid = 0,
+	.ro_scaling_factor = ipq9574_scaling_factor,
+	.sensor_range_start = 0,
+	.sensor_range_end = 6,
+	.init_voltage_step = 10000,
+	.init_voltage_width = 6,
+	.step_quot_init_min = 0,
+	.step_quot_init_max = 15,
+	.num_fuse_corners = 4,
+	.fuse_corner_data = (struct fuse_corner_data[]){
+		/* fuse corner 0 */
+		{
+			.ref_uV = 725000,
+			.max_uV = 725000,
+			.min_uV = 725000,
+			.range_uV = 0,
+			.volt_cloop_adjust = 0,
+			.volt_oloop_adjust = 0,
+			.max_volt_scale = 4,
+			.max_quot_scale = 10,
+			.quot_offset = 0,
+			.quot_scale = 1,
+			.quot_adjust = 0,
+			.quot_offset_scale = 5,
+			.quot_offset_adjust = 0,
+		},
+		/* fuse corner 1 */
+		{
+			.ref_uV = 862500,
+			.max_uV = 862500,
+			.min_uV = 725000,
+			.range_uV = 0,
+			.volt_cloop_adjust = 0,
+			.volt_oloop_adjust = 0,
+			.max_volt_scale = 500,
+			.max_quot_scale = 800,
+			.quot_offset = 0,
+			.quot_scale = 1,
+			.quot_adjust = 0,
+			.quot_offset_scale = 5,
+			.quot_offset_adjust = 0,
+		},
+		/* fuse corner 2 */
+		{
+			.ref_uV = 987500,
+			.max_uV = 987500,
+			.min_uV = 787500,
+			.range_uV = 0,
+			.volt_cloop_adjust = 0,
+			.volt_oloop_adjust = 0,
+			.max_volt_scale = 280,
+			.max_quot_scale = 650,
+			.quot_offset = 0,
+			.quot_scale = 1,
+			.quot_adjust = 0,
+			.quot_offset_scale = 5,
+			.quot_offset_adjust = 0,
+
+		},
+		/* fuse corner 3 */
+		{
+			.ref_uV = 1062500,
+			.max_uV = 1062500,
+			.min_uV = 850000,
+			.range_uV = 0,
+			.volt_cloop_adjust = 0,
+			.volt_oloop_adjust = 0,
+			.max_volt_scale = 430,
+			.max_quot_scale = 800,
+			.quot_offset = 0,
+			.quot_scale = 1,
+			.quot_adjust = 0,
+			.quot_offset_scale = 5,
+			.quot_offset_adjust = 0,
+		},
+	},
+};
+
+static const struct cpr_desc ipq9574_cpr_desc = {
+	.cpr_type = CTRL_TYPE_CPR4,
+	.num_threads = 1,
+	.apm_threshold = 850000,
+	.apm_crossover = 880000,
+	.apm_hysteresis = 0,
+	.cpr_base_voltage = 700000,
+	.cpr_max_voltage = 1100000,
+	.timer_delay_us = 5000,
+	.timer_cons_up = 0,
+	.timer_cons_down = 0,
+	.up_threshold = 2,
+	.down_threshold = 2,
+	.idle_clocks = 15,
+	.count_mode = CPR3_CPR_CTL_COUNT_MODE_ALL_AT_ONCE_MIN,
+	.count_repeat = 1,
+	.gcnt_us = 1,
+	.vreg_step_fixed = 12500,
+	.vreg_step_up_limit = 1,
+	.vreg_step_down_limit = 1,
+	.vdd_settle_time_us = 34,
+	.corner_settle_time_us = 6,
+	.reduce_to_corner_uV = true,
+	.hw_closed_loop_en = false,
+	.threads = (const struct cpr_thread_desc *[]) {
+		&ipq9574_thread,
+	},
+};
+
+static const struct cpr_acc_desc ipq9574_cpr_acc_desc = {
+	.cpr_desc = &ipq9574_cpr_desc,
+};
+
 static const int sdm630_gold_scaling_factor[][CPR3_RO_COUNT] = {
 	/* Same RO factors for all fuse corners */
 	{
@@ -2676,7 +2812,8 @@  static int cpr_probe(struct platform_device *pdev)
 	desc = data->cpr_desc;
 
 	/* CPRh disallows MEM-ACC access from the HLOS */
-	if (!data->acc_desc && desc->cpr_type < CTRL_TYPE_CPRH)
+	if (!data->acc_desc && desc->cpr_type < CTRL_TYPE_CPRH &&
+	    !of_device_is_compatible(dev->of_node, "qcom,ipq9574-cpr4"))
 		return -EINVAL;
 
 	drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
@@ -2703,7 +2840,8 @@  static int cpr_probe(struct platform_device *pdev)
 
 	mutex_init(&drv->lock);
 
-	if (desc->cpr_type < CTRL_TYPE_CPRH) {
+	if (desc->cpr_type < CTRL_TYPE_CPRH &&
+	    !of_device_is_compatible(dev->of_node, "qcom,ipq9574-cpr4")) {
 		np = of_parse_phandle(dev->of_node, "qcom,acc", 0);
 		if (!np)
 			return -ENODEV;
@@ -2828,6 +2966,7 @@  static void cpr_remove(struct platform_device *pdev)
 }
 
 static const struct of_device_id cpr3_match_table[] = {
+	{ .compatible = "qcom,ipq9574-cpr4", .data = &ipq9574_cpr_acc_desc },
 	{ .compatible = "qcom,msm8998-cprh", .data = &msm8998_cpr_acc_desc },
 	{ .compatible = "qcom,sdm630-cprh", .data = &sdm630_cpr_acc_desc },
 	{ }