| Message ID | 77f150522096d55c6da0ff983db61e0cf6309344.1709317289.git.geert+renesas@glider.be (mailing list archive) |
|---|---|
| State | Handled Elsewhere, archived |
| Headers | show |
| Series | pmdomain: renesas: rcar-gen4-sysc: Reduce atomic delays | expand |
On Fri, 1 Mar 2024 at 19:23, Geert Uytterhoeven <geert+renesas@glider.be> wrote: > > The delays used with the various atomic polling loops are already at the > maximum value of ~10µs, as documented for read_poll_timeout_atomic(). > Hence reduce the delays from 10 to 1 µs. Increase PDRESR_RETRIES > accordingly, to retain the old (generous) timeout value. > > Measurements on R-Car V3U, S4, V4H, and V4M show that the first three > polling loops rarely (never?) loop, so the actual delay does not matter. > The fourth loop (for SYSCISCR in rcar_gen4_sysc_power()) typically ran > for one or two cycles with the old delay. With the reduced delay, it > typically runs for two to 17 cycles, and finishes earlier than before, > which can reduce loop time up to a factor of three. > > While at it, rename the SYSCISR_{TIMEOUT,DELAY_US} definitions to > SYSCISCR_{TIMEOUT,DELAY_US}, to match the register name they apply to. > > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Applied for next, thanks! Kind regards Uffe > --- > drivers/pmdomain/renesas/rcar-gen4-sysc.c | 14 +++++++------- > 1 file changed, 7 insertions(+), 7 deletions(-) > > diff --git a/drivers/pmdomain/renesas/rcar-gen4-sysc.c b/drivers/pmdomain/renesas/rcar-gen4-sysc.c > index 728248659a97e8cc..66409cff2083fcd8 100644 > --- a/drivers/pmdomain/renesas/rcar-gen4-sysc.c > +++ b/drivers/pmdomain/renesas/rcar-gen4-sysc.c > @@ -50,13 +50,13 @@ > #define SYSCSR_BUSY GENMASK(1, 0) /* All bit sets is not busy */ > > #define SYSCSR_TIMEOUT 10000 > -#define SYSCSR_DELAY_US 10 > +#define SYSCSR_DELAY_US 1 > > -#define PDRESR_RETRIES 1000 > -#define PDRESR_DELAY_US 10 > +#define PDRESR_RETRIES 10000 > +#define PDRESR_DELAY_US 1 > > -#define SYSCISR_TIMEOUT 10000 > -#define SYSCISR_DELAY_US 10 > +#define SYSCISCR_TIMEOUT 10000 > +#define SYSCISCR_DELAY_US 1 > > #define RCAR_GEN4_PD_ALWAYS_ON 64 > #define NUM_DOMAINS_EACH_REG BITS_PER_TYPE(u32) > @@ -97,7 +97,7 @@ static int clear_irq_flags(unsigned int reg_idx, unsigned int isr_mask) > > ret = readl_poll_timeout_atomic(rcar_gen4_sysc_base + SYSCISCR(reg_idx), > val, !(val & isr_mask), > - SYSCISR_DELAY_US, SYSCISR_TIMEOUT); > + SYSCISCR_DELAY_US, SYSCISCR_TIMEOUT); > if (ret < 0) { > pr_err("\n %s : Can not clear IRQ flags in SYSCISCR", __func__); > return -EIO; > @@ -157,7 +157,7 @@ static int rcar_gen4_sysc_power(u8 pdr, bool on) > /* Wait until the power shutoff or resume request has completed * */ > ret = readl_poll_timeout_atomic(rcar_gen4_sysc_base + SYSCISCR(reg_idx), > val, (val & isr_mask), > - SYSCISR_DELAY_US, SYSCISR_TIMEOUT); > + SYSCISCR_DELAY_US, SYSCISCR_TIMEOUT); > if (ret < 0) { > ret = -EIO; > goto out; > -- > 2.34.1 >
diff --git a/drivers/pmdomain/renesas/rcar-gen4-sysc.c b/drivers/pmdomain/renesas/rcar-gen4-sysc.c index 728248659a97e8cc..66409cff2083fcd8 100644 --- a/drivers/pmdomain/renesas/rcar-gen4-sysc.c +++ b/drivers/pmdomain/renesas/rcar-gen4-sysc.c @@ -50,13 +50,13 @@ #define SYSCSR_BUSY GENMASK(1, 0) /* All bit sets is not busy */ #define SYSCSR_TIMEOUT 10000 -#define SYSCSR_DELAY_US 10 +#define SYSCSR_DELAY_US 1 -#define PDRESR_RETRIES 1000 -#define PDRESR_DELAY_US 10 +#define PDRESR_RETRIES 10000 +#define PDRESR_DELAY_US 1 -#define SYSCISR_TIMEOUT 10000 -#define SYSCISR_DELAY_US 10 +#define SYSCISCR_TIMEOUT 10000 +#define SYSCISCR_DELAY_US 1 #define RCAR_GEN4_PD_ALWAYS_ON 64 #define NUM_DOMAINS_EACH_REG BITS_PER_TYPE(u32) @@ -97,7 +97,7 @@ static int clear_irq_flags(unsigned int reg_idx, unsigned int isr_mask) ret = readl_poll_timeout_atomic(rcar_gen4_sysc_base + SYSCISCR(reg_idx), val, !(val & isr_mask), - SYSCISR_DELAY_US, SYSCISR_TIMEOUT); + SYSCISCR_DELAY_US, SYSCISCR_TIMEOUT); if (ret < 0) { pr_err("\n %s : Can not clear IRQ flags in SYSCISCR", __func__); return -EIO; @@ -157,7 +157,7 @@ static int rcar_gen4_sysc_power(u8 pdr, bool on) /* Wait until the power shutoff or resume request has completed * */ ret = readl_poll_timeout_atomic(rcar_gen4_sysc_base + SYSCISCR(reg_idx), val, (val & isr_mask), - SYSCISR_DELAY_US, SYSCISR_TIMEOUT); + SYSCISCR_DELAY_US, SYSCISCR_TIMEOUT); if (ret < 0) { ret = -EIO; goto out;
The delays used with the various atomic polling loops are already at the maximum value of ~10µs, as documented for read_poll_timeout_atomic(). Hence reduce the delays from 10 to 1 µs. Increase PDRESR_RETRIES accordingly, to retain the old (generous) timeout value. Measurements on R-Car V3U, S4, V4H, and V4M show that the first three polling loops rarely (never?) loop, so the actual delay does not matter. The fourth loop (for SYSCISCR in rcar_gen4_sysc_power()) typically ran for one or two cycles with the old delay. With the reduced delay, it typically runs for two to 17 cycles, and finishes earlier than before, which can reduce loop time up to a factor of three. While at it, rename the SYSCISR_{TIMEOUT,DELAY_US} definitions to SYSCISCR_{TIMEOUT,DELAY_US}, to match the register name they apply to. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- drivers/pmdomain/renesas/rcar-gen4-sysc.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)