mbox series

[00/12] Use qmp_send to update co-processor load state

Message ID 1618574638-5117-1-git-send-email-sibis@codeaurora.org (mailing list archive)
Headers show
Series Use qmp_send to update co-processor load state | expand

Message

Sibi Sankar April 16, 2021, 12:03 p.m. UTC
The power domains exposed by the AOSS QMP driver control the load state
resources linked to modem, adsp, cdsp remoteprocs. These are used to
notify the Always on Subsystem (AOSS) that a particular co-processor is
up/down. AOSS uses this information to wait for the co-processors to
suspend before starting its sleep sequence. These co-processors enter
low-power modes independent to that of the application processor and
the load state resources linked to them are expected to remain unaltered
across system suspend/resume cycles. To achieve this behavior lets stop
modeling them as power-domains and replace them with generic qmp_send
interface instead.

https://lore.kernel.org/lkml/20200913034603.GV3715@yoga/
Previous dicussion on dropping power-domain support from AOSS QMP driver

https://lore.kernel.org/lkml/1617943188-23278-2-git-send-email-deesin@qti.qualcomm.com/
Depends on ^^

Sibi Sankar (12):
  dt-bindings: soc: qcom: aoss: Drop power-domain bindings
  soc: qcom: aoss: Drop power domain support
  dt-bindings: remoteproc: qcom: pas: Add QMP bindings
  dt-bindings: remoteproc: qcom: Add QMP bindings
  remoteproc: qcom: q6v5: Use qmp_send to update co-processor load state
  arm64: dts: qcom: sc7180: Use QMP binding to control load state
  arm64: dts: qcom: sc7280: Use QMP binding to control load state
  arm64: dts: qcom: sdm845: Use QMP binding to control load state
  arm64: dts: qcom: sm8150: Use QMP binding to control load state
  arm64: dts: qcom: sm8250: Use QMP binding to control load state
  arm64: dts: qcom: sm8350: Use QMP binding to control load state
  dt-bindings: soc: qcom: aoss: Delete unused power-domain definitions

 .../devicetree/bindings/remoteproc/qcom,adsp.txt   |  11 ++-
 .../devicetree/bindings/remoteproc/qcom,q6v5.txt   |   7 +-
 .../devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt |  16 +--
 arch/arm64/boot/dts/qcom/sc7180.dtsi               |   9 +-
 arch/arm64/boot/dts/qcom/sc7280.dtsi               |   2 -
 arch/arm64/boot/dts/qcom/sdm845.dtsi               |   8 +-
 arch/arm64/boot/dts/qcom/sm8150.dtsi               |  28 +++---
 arch/arm64/boot/dts/qcom/sm8250.dtsi               |  22 ++---
 arch/arm64/boot/dts/qcom/sm8350.dtsi               |  30 +++---
 drivers/remoteproc/qcom_q6v5.c                     |  57 ++++++++++-
 drivers/remoteproc/qcom_q6v5.h                     |   7 +-
 drivers/remoteproc/qcom_q6v5_adsp.c                |   7 +-
 drivers/remoteproc/qcom_q6v5_mss.c                 |  44 ++-------
 drivers/remoteproc/qcom_q6v5_pas.c                 |  80 ++++-----------
 drivers/remoteproc/qcom_q6v5_wcss.c                |   4 +-
 drivers/soc/qcom/qcom_aoss.c                       | 109 +--------------------
 include/dt-bindings/power/qcom-aoss-qmp.h          |  14 ---
 17 files changed, 163 insertions(+), 292 deletions(-)
 delete mode 100644 include/dt-bindings/power/qcom-aoss-qmp.h