@@ -1,20 +1,21 @@
menu "Remoteproc drivers"
-# REMOTEPROC gets selected by whoever wants it
config REMOTEPROC
- tristate
+ tristate "Support for Remote Processor subsystem"
depends on HAS_DMA
select CRC32
select FW_LOADER
select VIRTIO
select VIRTUALIZATION
+if REMOTEPROC
+
config OMAP_REMOTEPROC
tristate "OMAP remoteproc support"
depends on HAS_DMA
depends on ARCH_OMAP4 || SOC_OMAP5
depends on OMAP_IOMMU
- select REMOTEPROC
+ depends on REMOTEPROC
select MAILBOX
select OMAP2PLUS_MBOX
select RPMSG_VIRTIO
@@ -34,7 +35,7 @@ config OMAP_REMOTEPROC
config STE_MODEM_RPROC
tristate "STE-Modem remoteproc support"
depends on HAS_DMA
- select REMOTEPROC
+ depends on REMOTEPROC
default n
help
Say y or m here to support STE-Modem shared memory driver.
@@ -44,7 +45,7 @@ config STE_MODEM_RPROC
config WKUP_M3_RPROC
tristate "AMx3xx Wakeup M3 remoteproc support"
depends on SOC_AM33XX || SOC_AM43XX
- select REMOTEPROC
+ depends on REMOTEPROC
help
Say y here to support Wakeup M3 remote processor on TI AM33xx
and AM43xx family of SoCs.
@@ -57,6 +58,7 @@ config WKUP_M3_RPROC
config DA8XX_REMOTEPROC
tristate "DA8xx/OMAP-L13x remoteproc support"
depends on ARCH_DAVINCI_DA8XX
+ depends on REMOTEPROC
select CMA if MMU
select RPMSG_VIRTIO
help
@@ -83,9 +85,9 @@ config QCOM_Q6V5_PIL
tristate "Qualcomm Hexagon V5 Peripherial Image Loader"
depends on OF && ARCH_QCOM
depends on QCOM_SMEM
+ depends on REMOTEPROC
select MFD_SYSCON
select QCOM_MDT_LOADER
- select REMOTEPROC
help
Say y here to support the Qualcomm Peripherial Image Loader for the
Hexagon V5 based remote processors.
@@ -109,7 +111,7 @@ config QCOM_WCNSS_PIL
config ST_REMOTEPROC
tristate "ST remoteproc support"
depends on ARCH_STI
- select REMOTEPROC
+ depends on REMOTEPROC
help
Say y here to support ST's adjunct processors via the remote
processor framework.
@@ -117,6 +119,8 @@ config ST_REMOTEPROC
config ST_SLIM_REMOTEPROC
tristate
- select REMOTEPROC
+ depends on REMOTEPROC
+
+endif # REMOTEPROC
endmenu
Make REMOTEPROC core a selectable kconfig option, and update remoteproc client drivers to 'depends on' the core. This avoids some nasty Kconfig recursive dependency issues. Also when using menuconfig client drivers will be hidden until the core has been enabled. Documentation/kbuild/kconfig-language.txt: Note: select should be used with care. select will force a symbol to a value without visiting the dependencies. By abusing select you are able to select a symbol FOO even if FOO depends on BAR that is not set. In general use select only for non-visible symbols (no prompts anywhere) and for symbols with no dependencies. That will limit the usefulness but on the other hand avoid the illegal configurations all over. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> --- drivers/remoteproc/Kconfig | 20 ++++++++++++-------- 1 file changed, 12 insertions(+), 8 deletions(-)