Message ID | 1681807721-32343-2-git-send-email-quic_sarannya@quicinc.com (mailing list archive) |
---|---|
State | Superseded |
Headers | show |
Series | rpmsg signaling/flowcontrol patches | expand |
Hi, On 4/18/23 10:48, Sarannya S wrote: > From: Deepak Kumar Singh <quic_deesin@quicinc.com> > > Some transports like Glink support the state notifications between > clients using flow control signals similar to serial protocol signals. > Local glink client drivers can send and receive flow control status > to glink clients running on remote processors. > > Add APIs to support sending and receiving of flow control status by > rpmsg clients. > > Signed-off-by: Deepak Kumar Singh <quic_deesin@quicinc.com> > Signed-off-by: Sarannya S <quic_sarannya@quicinc.com> > --- > drivers/rpmsg/rpmsg_core.c | 20 ++++++++++++++++++++ > drivers/rpmsg/rpmsg_internal.h | 2 ++ > 2 files changed, 22 insertions(+) > > diff --git a/drivers/rpmsg/rpmsg_core.c b/drivers/rpmsg/rpmsg_core.c > index a2207c0..86b4912 100644 > --- a/drivers/rpmsg/rpmsg_core.c > +++ b/drivers/rpmsg/rpmsg_core.c > @@ -331,6 +331,24 @@ int rpmsg_trysend_offchannel(struct rpmsg_endpoint *ept, u32 src, u32 dst, > EXPORT_SYMBOL(rpmsg_trysend_offchannel); > > /** > + * rpmsg_set_flow_control() - sets/clears serial flow control signals > + * @ept: the rpmsg endpoint > + * @enable: pause/resume incoming data flow > + * > + * Return: 0 on success and an appropriate error value on failure. > + */ > +int rpmsg_set_flow_control(struct rpmsg_endpoint *ept, bool enable) Regression since V4[1] In V4 version the function was: int rpmsg_set_flow_control(struct rpmsg_endpoint *ept, bool enable, u32 dst) Following comments on V3 [2] Without dst parameter it is not compatible with the rpmsg_virtio backend [1]https://lkml.org/lkml/2022/12/7/506 [2]https://www.spinics.net/lists/kernel/msg4573082.html Regards Arnaud > +{ > + if (WARN_ON(!ept)) > + return -EINVAL; > + if (!ept->ops->set_flow_control) > + return -ENXIO; > + > + return ept->ops->set_flow_control(ept, enable); > +} > +EXPORT_SYMBOL(rpmsg_set_flow_control); > + > +/** > * rpmsg_get_mtu() - get maximum transmission buffer size for sending message. > * @ept: the rpmsg endpoint > * > @@ -539,6 +557,8 @@ static int rpmsg_dev_probe(struct device *dev) > > rpdev->ept = ept; > rpdev->src = ept->addr; > + > + ept->flow_cb = rpdrv->flowcontrol; > } > > err = rpdrv->probe(rpdev); > diff --git a/drivers/rpmsg/rpmsg_internal.h b/drivers/rpmsg/rpmsg_internal.h > index 39b646d..4fea45a 100644 > --- a/drivers/rpmsg/rpmsg_internal.h > +++ b/drivers/rpmsg/rpmsg_internal.h > @@ -55,6 +55,7 @@ struct rpmsg_device_ops { > * @trysendto: see @rpmsg_trysendto(), optional > * @trysend_offchannel: see @rpmsg_trysend_offchannel(), optional > * @poll: see @rpmsg_poll(), optional > + * @set_flow_control: see @rpmsg_set_flow_control(), optional > * @get_mtu: see @rpmsg_get_mtu(), optional > * > * Indirection table for the operations that a rpmsg backend should implement. > @@ -75,6 +76,7 @@ struct rpmsg_endpoint_ops { > void *data, int len); > __poll_t (*poll)(struct rpmsg_endpoint *ept, struct file *filp, > poll_table *wait); > + int (*set_flow_control)(struct rpmsg_endpoint *ept, bool enable); > ssize_t (*get_mtu)(struct rpmsg_endpoint *ept); > }; >
On Wed, Apr 19, 2023 at 11:53:49AM +0200, Arnaud POULIQUEN wrote: > Hi, > > > On 4/18/23 10:48, Sarannya S wrote: > > From: Deepak Kumar Singh <quic_deesin@quicinc.com> > > > > Some transports like Glink support the state notifications between > > clients using flow control signals similar to serial protocol signals. > > Local glink client drivers can send and receive flow control status > > to glink clients running on remote processors. > > > > Add APIs to support sending and receiving of flow control status by > > rpmsg clients. > > > > Signed-off-by: Deepak Kumar Singh <quic_deesin@quicinc.com> > > Signed-off-by: Sarannya S <quic_sarannya@quicinc.com> > > --- > > drivers/rpmsg/rpmsg_core.c | 20 ++++++++++++++++++++ > > drivers/rpmsg/rpmsg_internal.h | 2 ++ > > 2 files changed, 22 insertions(+) > > > > diff --git a/drivers/rpmsg/rpmsg_core.c b/drivers/rpmsg/rpmsg_core.c > > index a2207c0..86b4912 100644 > > --- a/drivers/rpmsg/rpmsg_core.c > > +++ b/drivers/rpmsg/rpmsg_core.c > > @@ -331,6 +331,24 @@ int rpmsg_trysend_offchannel(struct rpmsg_endpoint *ept, u32 src, u32 dst, > > EXPORT_SYMBOL(rpmsg_trysend_offchannel); > > > > /** > > + * rpmsg_set_flow_control() - sets/clears serial flow control signals > > + * @ept: the rpmsg endpoint > > + * @enable: pause/resume incoming data flow > > + * > > + * Return: 0 on success and an appropriate error value on failure. > > + */ > > +int rpmsg_set_flow_control(struct rpmsg_endpoint *ept, bool enable) > > > Regression since V4[1] > > In V4 version the function was: > > int rpmsg_set_flow_control(struct rpmsg_endpoint *ept, bool enable, u32 dst) > > Following comments on V3 [2] > > Without dst parameter it is not compatible with the rpmsg_virtio backend > You're right, and I missed that this was gone again. Thanks for pointing it out. I've backed this series out of rpmsg-next again. v6 seems to carry the correct argument again... Regards, Bjorn > > [1]https://lkml.org/lkml/2022/12/7/506 > [2]https://www.spinics.net/lists/kernel/msg4573082.html > > Regards > Arnaud > > > +{ > > + if (WARN_ON(!ept)) > > + return -EINVAL; > > + if (!ept->ops->set_flow_control) > > + return -ENXIO; > > + > > + return ept->ops->set_flow_control(ept, enable); > > +} > > +EXPORT_SYMBOL(rpmsg_set_flow_control); > > + > > +/** > > * rpmsg_get_mtu() - get maximum transmission buffer size for sending message. > > * @ept: the rpmsg endpoint > > * > > @@ -539,6 +557,8 @@ static int rpmsg_dev_probe(struct device *dev) > > > > rpdev->ept = ept; > > rpdev->src = ept->addr; > > + > > + ept->flow_cb = rpdrv->flowcontrol; > > } > > > > err = rpdrv->probe(rpdev); > > diff --git a/drivers/rpmsg/rpmsg_internal.h b/drivers/rpmsg/rpmsg_internal.h > > index 39b646d..4fea45a 100644 > > --- a/drivers/rpmsg/rpmsg_internal.h > > +++ b/drivers/rpmsg/rpmsg_internal.h > > @@ -55,6 +55,7 @@ struct rpmsg_device_ops { > > * @trysendto: see @rpmsg_trysendto(), optional > > * @trysend_offchannel: see @rpmsg_trysend_offchannel(), optional > > * @poll: see @rpmsg_poll(), optional > > + * @set_flow_control: see @rpmsg_set_flow_control(), optional > > * @get_mtu: see @rpmsg_get_mtu(), optional > > * > > * Indirection table for the operations that a rpmsg backend should implement. > > @@ -75,6 +76,7 @@ struct rpmsg_endpoint_ops { > > void *data, int len); > > __poll_t (*poll)(struct rpmsg_endpoint *ept, struct file *filp, > > poll_table *wait); > > + int (*set_flow_control)(struct rpmsg_endpoint *ept, bool enable); > > ssize_t (*get_mtu)(struct rpmsg_endpoint *ept); > > }; > >
diff --git a/drivers/rpmsg/rpmsg_core.c b/drivers/rpmsg/rpmsg_core.c index a2207c0..86b4912 100644 --- a/drivers/rpmsg/rpmsg_core.c +++ b/drivers/rpmsg/rpmsg_core.c @@ -331,6 +331,24 @@ int rpmsg_trysend_offchannel(struct rpmsg_endpoint *ept, u32 src, u32 dst, EXPORT_SYMBOL(rpmsg_trysend_offchannel); /** + * rpmsg_set_flow_control() - sets/clears serial flow control signals + * @ept: the rpmsg endpoint + * @enable: pause/resume incoming data flow + * + * Return: 0 on success and an appropriate error value on failure. + */ +int rpmsg_set_flow_control(struct rpmsg_endpoint *ept, bool enable) +{ + if (WARN_ON(!ept)) + return -EINVAL; + if (!ept->ops->set_flow_control) + return -ENXIO; + + return ept->ops->set_flow_control(ept, enable); +} +EXPORT_SYMBOL(rpmsg_set_flow_control); + +/** * rpmsg_get_mtu() - get maximum transmission buffer size for sending message. * @ept: the rpmsg endpoint * @@ -539,6 +557,8 @@ static int rpmsg_dev_probe(struct device *dev) rpdev->ept = ept; rpdev->src = ept->addr; + + ept->flow_cb = rpdrv->flowcontrol; } err = rpdrv->probe(rpdev); diff --git a/drivers/rpmsg/rpmsg_internal.h b/drivers/rpmsg/rpmsg_internal.h index 39b646d..4fea45a 100644 --- a/drivers/rpmsg/rpmsg_internal.h +++ b/drivers/rpmsg/rpmsg_internal.h @@ -55,6 +55,7 @@ struct rpmsg_device_ops { * @trysendto: see @rpmsg_trysendto(), optional * @trysend_offchannel: see @rpmsg_trysend_offchannel(), optional * @poll: see @rpmsg_poll(), optional + * @set_flow_control: see @rpmsg_set_flow_control(), optional * @get_mtu: see @rpmsg_get_mtu(), optional * * Indirection table for the operations that a rpmsg backend should implement. @@ -75,6 +76,7 @@ struct rpmsg_endpoint_ops { void *data, int len); __poll_t (*poll)(struct rpmsg_endpoint *ept, struct file *filp, poll_table *wait); + int (*set_flow_control)(struct rpmsg_endpoint *ept, bool enable); ssize_t (*get_mtu)(struct rpmsg_endpoint *ept); };