| Message ID | 1535106262-13004-5-git-send-email-jacopo@jmondi.org (mailing list archive) |
|---|---|
| State | Not Applicable |
| Delegated to: | Geert Uytterhoeven |
| Headers | show |
| Series | vin-tests: Add D3 Draak support | expand |
Hi Jacopo, Thanks for your patch. On 2018-08-24 12:24:22 +0200, Jacopo Mondi wrote: > Add support for VIN4 to yavta-hdmi and check if format propagation should > go through 'mc_propagate_parallel()' if the HDMI receiver chip is an > ADV7612 one. > > Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> > --- > yavta-hdmi | 13 +++++++++++-- > 1 file changed, 11 insertions(+), 2 deletions(-) > > diff --git a/yavta-hdmi b/yavta-hdmi > index fdec546..2e3b625 100755 > --- a/yavta-hdmi > +++ b/yavta-hdmi > @@ -33,14 +33,23 @@ case $vc in > dev=/dev/$vin3 > csipad=4 > ;; > + 4) > + vinname=$vinname4 > + dev=/dev/$vin4 I think you should also add a csipad declaration here as if the script is used on a board which is not D3 VIN4 would be connected to a CSI-2 bus. Writing that I realise a new var 'csidev' or something would be needed here to expand this to cover the full range of VIN0-VIN7. > + ;; > *) > echo "Unkown VC '$vc'" > exit 1 > esac > > mc_reset > -mc_set_link "$csi40name" $csipad "$vinname" 1 > -mc_propagate_format "$hdminame" 1 "$txaname" 0 "$csi40name" $csipad "$vinname" > +if [[ "$hdminame" == "adv7612 0-004c" ]]; then You should use $parallelname here not $hdminame. Furthermore I thin you should check if the variable is empty or not and not target it for a specific board. A good (or only) example of how I think this should be done can be found in test-qv4l2.sh. if [[ "$csi20name" != "" ]]; then mc_set_link "$csi20name" 1 "$vinname1" 1 mc_propagate_cvbs "$vinname1" qv4l2 -d /dev/$vin1 fi if [[ "$parallelname" != "" ]]; then mc_reset mc_set_link "$parallelname" 1 "$vinname0" 1 mc_propagate_parallel "$vinname0" qv4l2 -d /dev/$vin0 fi > + mc_set_link "$hdminame" 1 "$vinname" 1 > + mc_propagate_parallel "$vinname" > +else > + mc_set_link "$csi40name" $csipad "$vinname" 1 > + mc_propagate_format "$hdminame" 1 "$txaname" 0 "$csi40name" $csipad "$vinname" > +fi > > out=/tmp/vin-tests > rm -fr $out > -- > 2.7.4 >
Hi Niklas, On Fri, Aug 24, 2018 at 06:27:02PM +0200, Niklas Söderlund wrote: > Hi Jacopo, > > Thanks for your patch. > > On 2018-08-24 12:24:22 +0200, Jacopo Mondi wrote: > > Add support for VIN4 to yavta-hdmi and check if format propagation should > > go through 'mc_propagate_parallel()' if the HDMI receiver chip is an > > ADV7612 one. > > > > Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> > > --- > > yavta-hdmi | 13 +++++++++++-- > > 1 file changed, 11 insertions(+), 2 deletions(-) > > > > diff --git a/yavta-hdmi b/yavta-hdmi > > index fdec546..2e3b625 100755 > > --- a/yavta-hdmi > > +++ b/yavta-hdmi > > @@ -33,14 +33,23 @@ case $vc in > > dev=/dev/$vin3 > > csipad=4 > > ;; > > + 4) > > + vinname=$vinname4 > > + dev=/dev/$vin4 > > I think you should also add a csipad declaration here as if the script > is used on a board which is not D3 VIN4 would be connected to a CSI-2 > bus. Writing that I realise a new var 'csidev' or something would be > needed here to expand this to cover the full range of VIN0-VIN7. > > > + ;; > > *) > > echo "Unkown VC '$vc'" > > exit 1 > > esac > > > > mc_reset > > -mc_set_link "$csi40name" $csipad "$vinname" 1 > > -mc_propagate_format "$hdminame" 1 "$txaname" 0 "$csi40name" $csipad "$vinname" > > +if [[ "$hdminame" == "adv7612 0-004c" ]]; then > > > You should use $parallelname here not $hdminame. Furthermore I thin you > should check if the variable is empty or not and not target it for a > specific board. > > A good (or only) example of how I think this should be done can be found > in test-qv4l2.sh. > > if [[ "$csi20name" != "" ]]; then > mc_set_link "$csi20name" 1 "$vinname1" 1 > mc_propagate_cvbs "$vinname1" > qv4l2 -d /dev/$vin1 > fi > > if [[ "$parallelname" != "" ]]; then > mc_reset > mc_set_link "$parallelname" 1 "$vinname0" 1 > mc_propagate_parallel "$vinname0" > qv4l2 -d /dev/$vin0 > fi > This will solve the naming thing in boards.sh I'll try that and have a look at test-qv4l2.sh too! Thanks j > > + mc_set_link "$hdminame" 1 "$vinname" 1 > > + mc_propagate_parallel "$vinname" > > +else > > + mc_set_link "$csi40name" $csipad "$vinname" 1 > > + mc_propagate_format "$hdminame" 1 "$txaname" 0 "$csi40name" $csipad "$vinname" > > +fi > > > > out=/tmp/vin-tests > > rm -fr $out > > -- > > 2.7.4 > > > > -- > Regards, > Niklas Söderlund
diff --git a/yavta-hdmi b/yavta-hdmi index fdec546..2e3b625 100755 --- a/yavta-hdmi +++ b/yavta-hdmi @@ -33,14 +33,23 @@ case $vc in dev=/dev/$vin3 csipad=4 ;; + 4) + vinname=$vinname4 + dev=/dev/$vin4 + ;; *) echo "Unkown VC '$vc'" exit 1 esac mc_reset -mc_set_link "$csi40name" $csipad "$vinname" 1 -mc_propagate_format "$hdminame" 1 "$txaname" 0 "$csi40name" $csipad "$vinname" +if [[ "$hdminame" == "adv7612 0-004c" ]]; then + mc_set_link "$hdminame" 1 "$vinname" 1 + mc_propagate_parallel "$vinname" +else + mc_set_link "$csi40name" $csipad "$vinname" 1 + mc_propagate_format "$hdminame" 1 "$txaname" 0 "$csi40name" $csipad "$vinname" +fi out=/tmp/vin-tests rm -fr $out
Add support for VIN4 to yavta-hdmi and check if format propagation should go through 'mc_propagate_parallel()' if the HDMI receiver chip is an ADV7612 one. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> --- yavta-hdmi | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)