new file mode 100644
@@ -0,0 +1,79 @@
+Renesas R-Car MIPI CSI-2 driver (rcar-csi2)
+-------------------------------------------
+
+The rcar-csi2 device provides MIPI CSI-2 capabilities for the Renesas R-Car
+family of devices. It is to be used in conjunction with the rcar-vin driver which
+provides the video input capabilities.
+
+ - compatible: Must be one or more of the following
+ - "renesas,r8a7795-csi2" for the R8A7795 device
+ - "renesas,rcar-gen3-csi2" for a generic R-Car Gen3 compatible device.
+
+ When compatible with the generic version nodes must list the
+ SoC-specific version corresponding to the platform first
+ followed by the generic version.
+
+ - reg: the register base and size for the device registers
+ - interrupts: the interrupt for the device
+ - clocks: Reference to the parent clock
+
+The device node should contain two 'port' child nodes with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+media/video-interfaces.txt. Port 0 should connect the device that is the CSI-2
+producer. Port 1 should connect the R-Car VIN device (rcar-vin) consumer.
+
+ - ports:
+ - port@0: sub-node describing a endpoint to the CSI-2 source
+ - port@1: sub-node describing a endpoint to the VIN consumer
+
+Additionally, an alias named csiX will need to be created to specify
+which CSI-2 device this is.
+
+Example:
+
+/* SoC properties */
+
+ aliases {
+ csi40 = &csi40;
+ };
+
+ csi40: csi2@feaa0000 {
+ compatible = "renesas,r8a7795-csi2";
+ reg = <0 0xfeaa0000 0 0x10000>;
+ interrupts = <0 246 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 716>;
+ power-domains = <&cpg>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ csi40_out: endpoint@1 {
+ remote-endpoint = <&vin0csi40>;
+ };
+ };
+ };
+ };
+
+/* Board properties */
+
+ &csi40 {
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ csi40_in: endpoint@0 {
+ clock-lanes = <0>;
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&adv7482_1_out>;
+ };
+ };
+ };
+ };
@@ -9,3 +9,14 @@ config VIDEO_RCAR_VIN
To compile this driver as a module, choose M here: the
module will be called rcar-vin.
+
+config VIDEO_RCAR_CSI2
+ tristate "R-Car MIPI CSI-2 Interface driver"
+ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && OF
+ depends on ARCH_RENESAS || COMPILE_TEST
+ ---help---
+ Support for Renesas R-Car MIPI CSI-2 interface driver.
+ Supports R-Car Gen3 SoCs.
+
+ To compile this driver as a module, choose M here: the
+ module will be called rcar-csi2.
@@ -1,3 +1,5 @@
rcar-vin-objs = rcar-core.o rcar-dma.o rcar-v4l2.o
obj-$(CONFIG_VIDEO_RCAR_VIN) += rcar-vin.o
+
+obj-$(CONFIG_VIDEO_RCAR_CSI2) += rcar-csi2.o
new file mode 100644
@@ -0,0 +1,544 @@
+/*
+ * Driver for Renesas R-Car MIPI CSI-2
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#include <media/v4l2-of.h>
+#include <media/v4l2-subdev.h>
+
+/* Register offsets */
+#define TREF_REG 0x00 /* Control Timing Select */
+#define SRST_REG 0x04 /* Software Reset */
+#define PHYCNT_REG 0x08 /* PHY Operation Control */
+#define CHKSUM_REG 0x0C /* Checksum Control */
+#define VCDT_REG 0x10 /* Channel Data Type Select */
+#define VCDT2_REG 0x14 /* Channel Data Type Select 2 */
+#define FRDT_REG 0x18 /* Frame Data Type Select */
+#define FLD_REG 0x1C /* Field Detection Control */
+#define ASTBY_REG 0x20 /* Automatic Standby Control */
+#define LNGDT0_REG 0x28 /* Long Data Type Setting 0 */
+#define LNGDT1_REG 0x2C /* Long Data Type Setting 1 */
+#define INTEN_REG 0x30 /* Interrupt Enable */
+#define INTCLOSE_REG 0x34 /* Interrupt Source Mask */
+#define INTSTATE_REG 0x38 /* Interrupt Status Monitor */
+#define INTERRSTATE_REG 0x3C /* Interrupt Error Status Monitor */
+#define SHPDAT_REG 0x40 /* Short Packet Data */
+#define SHPCNT_REG 0x44 /* Short Packet Count */
+#define LINKCNT_REG 0x48 /* LINK Operation Control */
+#define LSWAP_REG 0x4C /* Lane Swap */
+#define PHTC_REG 0x58 /* PHY Test Interface Clear */
+#define PHYPLL_REG 0x68 /* PHY Frequency Control */
+#define PHEERM_REG 0x74 /* PHY ESC Error Monitor */
+#define PHCLM_REG 0x78 /* PHY Clock Lane Monitor */
+#define PHDLM_REG 0x7C /* PHY Data Lane Monitor */
+
+/* Control Timing Select bits */
+#define TREF_TREF (1 << 0)
+
+/* Software Reset bits */
+#define SRST_SRST (1 << 0)
+
+/* PHY Operation Control bits */
+#define PHYCNT_SHUTDOWNZ (1 << 17)
+#define PHYCNT_RSTZ (1 << 16)
+#define PHYCNT_ENABLECLK (1 << 4)
+#define PHYCNT_ENABLE_3 (1 << 3)
+#define PHYCNT_ENABLE_2 (1 << 2)
+#define PHYCNT_ENABLE_1 (1 << 1)
+#define PHYCNT_ENABLE_0 (1 << 0)
+
+/* Checksum Control bits */
+#define CHKSUM_ECC_EN (1 << 1)
+#define CHKSUM_CRC_EN (1 << 0)
+
+/*
+ * Channel Data Type Select bits
+ * VCDT[0-15]: Channel 1 VCDT[16-31]: Channel 2
+ * VCDT2[0-15]: Channel 3 VCDT2[16-31]: Channel 4
+ */
+#define VCDT_VCDTN_EN (1 << 15)
+#define VCDT_SEL_VC(n) ((n & 0x3) << 8)
+#define VCDT_SEL_DTN_ON (1 << 6)
+#define VCDT_SEL_DT(n) ((n & 0x1f) << 0)
+
+/* Field Detection Control bits */
+#define FLD_FLD_NUM(n) ((n & 0xff) << 16)
+#define FLD_FLD_EN4 (1 << 3)
+#define FLD_FLD_EN3 (1 << 2)
+#define FLD_FLD_EN2 (1 << 1)
+#define FLD_FLD_EN (1 << 0)
+
+/* LINK Operation Control bits */
+#define LINKCNT_MONITOR_EN (1 << 31)
+#define LINKCNT_REG_MONI_PACT_EN (1 << 25)
+#define LINKCNT_ICLK_NONSTOP (1 << 24)
+
+/* Lane Swap bits */
+#define LSWAP_L3SEL(n) ((n & 0x3) << 6)
+#define LSWAP_L2SEL(n) ((n & 0x3) << 4)
+#define LSWAP_L1SEL(n) ((n & 0x3) << 2)
+#define LSWAP_L0SEL(n) ((n & 0x3) << 0)
+
+/* PHY Test Interface Clear bits */
+#define PHTC_TESTCLR (1 << 0)
+
+/* PHY Frequency Control bits */
+#define PHYPLL_HSFREQRANGE_80MBPS (0x00 << 16)
+#define PHYPLL_HSFREQRANGE_90MBPS (0x10 << 16)
+#define PHYPLL_HSFREQRANGE_100MBPS (0x20 << 16)
+#define PHYPLL_HSFREQRANGE_110MBPS (0x30 << 16)
+#define PHYPLL_HSFREQRANGE_120MBPS (0x01 << 16)
+#define PHYPLL_HSFREQRANGE_130MBPS (0x11 << 16)
+#define PHYPLL_HSFREQRANGE_140MBPS (0x21 << 16)
+#define PHYPLL_HSFREQRANGE_150MBPS (0x31 << 16)
+#define PHYPLL_HSFREQRANGE_160MBPS (0x02 << 16)
+#define PHYPLL_HSFREQRANGE_170MBPS (0x12 << 16)
+#define PHYPLL_HSFREQRANGE_180MBPS (0x22 << 16)
+#define PHYPLL_HSFREQRANGE_190MBPS (0x32 << 16)
+#define PHYPLL_HSFREQRANGE_205MBPS (0x03 << 16)
+#define PHYPLL_HSFREQRANGE_220MBPS (0x13 << 16)
+#define PHYPLL_HSFREQRANGE_235MBPS (0x23 << 16)
+#define PHYPLL_HSFREQRANGE_250MBPS (0x33 << 16)
+#define PHYPLL_HSFREQRANGE_275MBPS (0x04 << 16)
+#define PHYPLL_HSFREQRANGE_300MBPS (0x14 << 16)
+#define PHYPLL_HSFREQRANGE_325MBPS (0x05 << 16)
+#define PHYPLL_HSFREQRANGE_350MBPS (0x15 << 16)
+#define PHYPLL_HSFREQRANGE_400MBPS (0x25 << 16)
+#define PHYPLL_HSFREQRANGE_450MBPS (0x06 << 16)
+#define PHYPLL_HSFREQRANGE_500MBPS (0x16 << 16)
+#define PHYPLL_HSFREQRANGE_550MBPS (0x07 << 16)
+#define PHYPLL_HSFREQRANGE_600MBPS (0x17 << 16)
+#define PHYPLL_HSFREQRANGE_650MBPS (0x08 << 16)
+#define PHYPLL_HSFREQRANGE_700MBPS (0x18 << 16)
+#define PHYPLL_HSFREQRANGE_750MBPS (0x09 << 16)
+#define PHYPLL_HSFREQRANGE_800MBPS (0x19 << 16)
+#define PHYPLL_HSFREQRANGE_850MBPS (0x29 << 16)
+#define PHYPLL_HSFREQRANGE_900MBPS (0x39 << 16)
+#define PHYPLL_HSFREQRANGE_950MBPS (0x0A << 16)
+#define PHYPLL_HSFREQRANGE_1000MBPS (0x1A << 16)
+#define PHYPLL_HSFREQRANGE_1050MBPS (0x2A << 16)
+#define PHYPLL_HSFREQRANGE_1100MBPS (0x3A << 16)
+#define PHYPLL_HSFREQRANGE_1150MBPS (0x0B << 16)
+#define PHYPLL_HSFREQRANGE_1200MBPS (0x1B << 16)
+#define PHYPLL_HSFREQRANGE_1250MBPS (0x2B << 16)
+#define PHYPLL_HSFREQRANGE_1300MBPS (0x3B << 16)
+#define PHYPLL_HSFREQRANGE_1350MBPS (0x0C << 16)
+#define PHYPLL_HSFREQRANGE_1400MBPS (0x1C << 16)
+#define PHYPLL_HSFREQRANGE_1450MBPS (0x2C << 16)
+#define PHYPLL_HSFREQRANGE_1500MBPS (0x3C << 16)
+
+struct rcar_csi2 {
+ struct device *dev;
+ void __iomem *base;
+ spinlock_t lock;
+
+ unsigned short lanes;
+ unsigned char swap[4];
+
+ struct v4l2_subdev subdev;
+ struct v4l2_mbus_framefmt mf;
+};
+
+#define csi_dbg(p, fmt, arg...) dev_dbg(p->dev, fmt, ##arg)
+#define csi_info(p, fmt, arg...) dev_info(p->dev, fmt, ##arg)
+#define csi_warn(p, fmt, arg...) dev_warn(p->dev, fmt, ##arg)
+#define csi_err(p, fmt, arg...) dev_err(p->dev, fmt, ##arg)
+
+static irqreturn_t rcar_csi2_irq(int irq, void *data)
+{
+ struct rcar_csi2 *priv = data;
+ u32 int_status;
+ unsigned int handled = 0;
+
+ spin_lock(&priv->lock);
+
+ int_status = ioread32(priv->base + INTSTATE_REG);
+ if (!int_status)
+ goto done;
+
+ /* ack interrupts */
+ iowrite32(int_status, priv->base + INTSTATE_REG);
+ handled = 1;
+
+done:
+ spin_unlock(&priv->lock);
+
+ return IRQ_RETVAL(handled);
+
+}
+
+static void rcar_csi2_reset(struct rcar_csi2 *priv)
+{
+ iowrite32(SRST_SRST, priv->base + SRST_REG);
+ udelay(5);
+ iowrite32(0, priv->base + SRST_REG);
+}
+
+static void rcar_csi2_wait_phy_start(struct rcar_csi2 *priv)
+{
+ int timeout;
+
+ /* Read the PHY clock lane monitor register (PHCLM). */
+ for (timeout = 100; timeout >= 0; timeout--) {
+ if (ioread32(priv->base + PHCLM_REG) & 0x01) {
+ csi_dbg(priv, "Detected the PHY clock lane\n");
+ break;
+ }
+ msleep(20);
+ }
+ if (!timeout)
+ csi_err(priv, "Timeout of reading the PHY clock lane\n");
+
+
+ /* Read the PHY data lane monitor register (PHDLM). */
+ for (timeout = 100; timeout >= 0; timeout--) {
+ if (ioread32(priv->base + PHDLM_REG) & 0x01) {
+ csi_dbg(priv, "Detected the PHY data lane\n");
+ break;
+ }
+ msleep(20);
+ }
+ if (!timeout)
+ csi_err(priv, "Timeout of reading the PHY data lane\n");
+
+}
+
+static int rcar_csi2_start(struct rcar_csi2 *priv)
+{
+ u32 fld, phycnt, phypll, vcdt, vcdt2, tmp, pixels;
+ int i;
+
+ csi_dbg(priv, "Input size (%dx%d%c)\n", priv->mf.width, priv->mf.height,
+ priv->mf.field == V4L2_FIELD_NONE ? 'p' : 'i');
+
+ vcdt = vcdt2 = 0;
+ for (i = 0; i < priv->lanes; i++) {
+ tmp = VCDT_SEL_VC(i) | VCDT_VCDTN_EN | VCDT_SEL_DTN_ON;
+
+ switch (priv->mf.code) {
+ case MEDIA_BUS_FMT_RGB888_1X24:
+ /* 24 == RGB888 */
+ tmp |= 0x24;
+ break;
+ case MEDIA_BUS_FMT_YUYV8_1X16:
+ case MEDIA_BUS_FMT_YUYV8_2X8:
+ case MEDIA_BUS_FMT_YUYV10_2X10:
+ /* 1E == YUV422 8-bit */
+ tmp |= 0x1e;
+ break;
+ default:
+ csi_warn(priv,
+ "Unknown media bus format, try it anyway\n");
+ break;
+ }
+
+ /* Store in correct reg and offset */
+ if (i < 2)
+ vcdt |= tmp << ((i % 2) * 16);
+ else
+ vcdt2 |= tmp << ((i % 2) * 16);
+ }
+
+ switch (priv->lanes) {
+ case 1:
+ fld = FLD_FLD_NUM(1) | FLD_FLD_EN;
+ phycnt = PHYCNT_ENABLECLK | PHYCNT_ENABLE_0;
+ phypll = PHYPLL_HSFREQRANGE_400MBPS;
+ break;
+ case 4:
+ fld = FLD_FLD_NUM(2) | FLD_FLD_EN4 | FLD_FLD_EN3 |
+ FLD_FLD_EN2 | FLD_FLD_EN;
+ phycnt = PHYCNT_ENABLECLK | PHYCNT_ENABLE_3 |
+ PHYCNT_ENABLE_2 | PHYCNT_ENABLE_1 | PHYCNT_ENABLE_0;
+
+ /* Calculate MBPS per lane, assume 32 bits per pixel at 60Hz */
+ pixels = (priv->mf.width * priv->mf.height) /
+ (priv->mf.field == V4L2_FIELD_NONE ? 1 : 2);
+ if (pixels <= 640 * 480)
+ phypll = PHYPLL_HSFREQRANGE_100MBPS;
+ else if (pixels <= 720 * 576)
+ phypll = PHYPLL_HSFREQRANGE_190MBPS;
+ else if (pixels <= 1280 * 720)
+ phypll = PHYPLL_HSFREQRANGE_450MBPS;
+ else if (pixels <= 1920 * 1080)
+ phypll = PHYPLL_HSFREQRANGE_900MBPS;
+ else
+ goto error;
+
+ break;
+ default:
+ goto error;
+ }
+
+ /* Init */
+ iowrite32(TREF_TREF, priv->base + TREF_REG);
+ rcar_csi2_reset(priv);
+ iowrite32(0, priv->base + PHTC_REG);
+
+ /* Configure */
+ iowrite32(fld, priv->base + FLD_REG);
+ iowrite32(vcdt, priv->base + VCDT_REG);
+ iowrite32(vcdt2, priv->base + VCDT2_REG);
+ iowrite32(LSWAP_L0SEL(priv->swap[0]) | LSWAP_L1SEL(priv->swap[1]) |
+ LSWAP_L2SEL(priv->swap[2]) | LSWAP_L3SEL(priv->swap[3]),
+ priv->base + LSWAP_REG);
+
+ /* Start */
+ iowrite32(phypll, priv->base + PHYPLL_REG);
+ iowrite32(phycnt, priv->base + PHYCNT_REG);
+ iowrite32(LINKCNT_MONITOR_EN | LINKCNT_REG_MONI_PACT_EN |
+ LINKCNT_ICLK_NONSTOP, priv->base + LINKCNT_REG);
+ iowrite32(phycnt | PHYCNT_SHUTDOWNZ, priv->base + PHYCNT_REG);
+ iowrite32(phycnt | PHYCNT_SHUTDOWNZ | PHYCNT_RSTZ,
+ priv->base + PHYCNT_REG);
+
+ rcar_csi2_wait_phy_start(priv);
+
+ return 0;
+error:
+ csi_err(priv, "Unsupported resolution (%dx%d%c)\n",
+ priv->mf.width, priv->mf.height,
+ priv->mf.field == V4L2_FIELD_NONE ? 'p' : 'i');
+
+ return -EINVAL;
+}
+
+static void rcar_csi2_stop(struct rcar_csi2 *priv)
+{
+ iowrite32(0, priv->base + PHYCNT_REG);
+
+ rcar_csi2_reset(priv);
+}
+
+static int rcar_csi2_s_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct rcar_csi2 *priv = container_of(sd, struct rcar_csi2, subdev);
+
+ if (enable)
+ return rcar_csi2_start(priv);
+
+ rcar_csi2_stop(priv);
+
+ return 0;
+}
+
+static int rcar_csi2_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *format)
+{
+ struct rcar_csi2 *priv = container_of(sd, struct rcar_csi2, subdev);
+
+ if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+ priv->mf = format->format;
+
+ return 0;
+}
+
+static int rcar_csi2_s_power(struct v4l2_subdev *sd, int on)
+{
+ struct rcar_csi2 *priv = container_of(sd, struct rcar_csi2, subdev);
+
+ if (on)
+ pm_runtime_get_sync(priv->dev);
+ else
+ pm_runtime_put_sync(priv->dev);
+
+ return 0;
+}
+
+static const struct v4l2_subdev_video_ops rcar_csi2_video_ops = {
+ .s_stream = rcar_csi2_s_stream,
+};
+
+static struct v4l2_subdev_core_ops rcar_csi2_subdev_core_ops = {
+ .s_power = rcar_csi2_s_power,
+};
+
+static const struct v4l2_subdev_pad_ops rcar_csi2_pad_ops = {
+ .set_fmt = rcar_csi2_set_pad_format,
+};
+
+static struct v4l2_subdev_ops rcar_csi2_subdev_ops = {
+ .video = &rcar_csi2_video_ops,
+ .core = &rcar_csi2_subdev_core_ops,
+ .pad = &rcar_csi2_pad_ops,
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static const struct of_device_id rcar_csi2_of_table[] = {
+ { .compatible = "renesas,r8a7795-csi2" },
+ { .compatible = "renesas,rcar-gen3-csi2" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, rcar_csi2_of_table);
+
+static int rcar_csi2_parse_dt(struct rcar_csi2 *priv)
+{
+ struct v4l2_of_endpoint v4l2_ep;
+ struct device_node *ep;
+ int i, n, ret;
+
+ ep = of_graph_get_endpoint_by_regs(priv->dev->of_node, 0, 0);
+ if (!ep)
+ return -EINVAL;
+
+ ret = v4l2_of_parse_endpoint(ep, &v4l2_ep);
+ of_node_put(ep);
+ if (ret) {
+ csi_err(priv, "Could not parse v4l2 endpoint\n");
+ return -EINVAL;
+ }
+
+ if (v4l2_ep.bus_type != V4L2_MBUS_CSI2) {
+ csi_err(priv, "Unsupported media bus type for %s\n",
+ of_node_full_name(ep));
+ return -EINVAL;
+ }
+
+ switch (v4l2_ep.bus.mipi_csi2.num_data_lanes) {
+ case 1:
+ case 4:
+ priv->lanes = v4l2_ep.bus.mipi_csi2.num_data_lanes;
+ break;
+ default:
+ csi_err(priv, "Unsupported number of lanes\n");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < 4; i++)
+ priv->swap[i] = i;
+
+ for (i = 0; i < priv->lanes; i++) {
+ /* Check for valid lane number */
+ if (v4l2_ep.bus.mipi_csi2.data_lanes[i] < 1 ||
+ v4l2_ep.bus.mipi_csi2.data_lanes[i] > 4) {
+ csi_err(priv, "data lanes must be in 1-4 range\n");
+ return -EINVAL;
+ }
+
+ /* Use lane numbers 0-3 internally */
+ priv->swap[i] = v4l2_ep.bus.mipi_csi2.data_lanes[i] - 1;
+
+
+ }
+
+ /* Make sure there are no duplicates */
+ for (i = 0; i < priv->lanes; i++) {
+ for (n = i + 1; n < priv->lanes; n++) {
+ if (priv->swap[i] == priv->swap[n]) {
+ csi_err(priv,
+ "Requested swapping not possible\n");
+ return -EINVAL;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int rcar_csi2_probe_resources(struct rcar_csi2 *priv,
+ struct platform_device *pdev)
+{
+ struct resource *mem;
+ int irq;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem)
+ return -ENODEV;
+
+ priv->base = devm_ioremap_resource(&pdev->dev, mem);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ irq = platform_get_irq(pdev, 0);
+ if (!irq)
+ return -ENODEV;
+
+ return devm_request_irq(&pdev->dev, irq, rcar_csi2_irq, IRQF_SHARED,
+ dev_name(&pdev->dev), priv);
+}
+
+static int rcar_csi2_probe(struct platform_device *pdev)
+{
+ struct rcar_csi2 *priv;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(struct rcar_csi2), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+
+ priv->dev = &pdev->dev;
+ spin_lock_init(&priv->lock);
+
+ ret = rcar_csi2_parse_dt(priv);
+ if (ret)
+ return ret;
+
+ ret = rcar_csi2_probe_resources(priv, pdev);
+ if (ret) {
+ csi_err(priv, "Failed to get resources\n");
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ priv->subdev.owner = THIS_MODULE;
+ priv->subdev.dev = &pdev->dev;
+ v4l2_subdev_init(&priv->subdev, &rcar_csi2_subdev_ops);
+ v4l2_set_subdevdata(&priv->subdev, &pdev->dev);
+ snprintf(priv->subdev.name, V4L2_SUBDEV_NAME_SIZE, "rcar_csi2.%s",
+ dev_name(&pdev->dev));
+
+ ret = v4l2_async_register_subdev(&priv->subdev);
+ if (ret < 0)
+ return ret;
+
+ pm_runtime_enable(&pdev->dev);
+
+ csi_info(priv, "%d lanes found\n", priv->lanes);
+
+ return 0;
+}
+
+static int rcar_csi2_remove(struct platform_device *pdev)
+{
+ struct rcar_csi2 *priv = platform_get_drvdata(pdev);
+
+ v4l2_async_unregister_subdev(&priv->subdev);
+
+ pm_runtime_disable(&pdev->dev);
+
+ return 0;
+}
+
+static struct platform_driver __refdata rcar_csi2_pdrv = {
+ .remove = rcar_csi2_remove,
+ .probe = rcar_csi2_probe,
+ .driver = {
+ .name = "rcar-csi2",
+ .of_match_table = of_match_ptr(rcar_csi2_of_table),
+ },
+};
+
+module_platform_driver(rcar_csi2_pdrv);
+
+MODULE_AUTHOR("Niklas Söderlund <niklas.soderlund@ragnatech.se>");
+MODULE_DESCRIPTION("Renesas R-Car MIPI CSI-2 driver");
+MODULE_LICENSE("GPL v2");
A V4L2 driver for Renesas R-Car MIPI CSI-2 interface. The driver supports the rcar-vin driver on R-Car Gen3 SoCs where a separate driver is needed to receive CSI-2. Driver is based on a prototype by Koji Matsuoka in the Renesas BSP. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> --- .../devicetree/bindings/media/rcar-csi2.txt | 79 +++ drivers/media/platform/rcar-vin/Kconfig | 11 + drivers/media/platform/rcar-vin/Makefile | 2 + drivers/media/platform/rcar-vin/rcar-csi2.c | 544 +++++++++++++++++++++ 4 files changed, 636 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/rcar-csi2.txt create mode 100644 drivers/media/platform/rcar-vin/rcar-csi2.c