@@ -791,6 +791,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
r8a7778-bockw.dtb \
r8a7779-marzen.dtb \
r8a7790-lager.dtb \
+ r8a7790-stout.dtb \
r8a7791-koelsch.dtb \
r8a7791-porter.dtb \
r8a7792-blanche.dtb \
new file mode 100644
@@ -0,0 +1,363 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Stout board
+ *
+ * Copyright (C) 2018 Marek Vasut <marek.vasut@gmail.com>
+ */
+
+/dts-v1/;
+#include "r8a7790.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Stout";
+ compatible = "renesas,stout", "renesas,r8a7790";
+
+ aliases {
+ serial0 = &scifa0;
+ };
+
+ chosen {
+ bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x40000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led1 {
+ gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+ };
+ led2 {
+ gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
+ };
+ led3 {
+ gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
+ };
+ led5 {
+ gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ fixedregulator3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_sdhi0: regulator-vcc-sdhi0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_out: endpoint {
+ remote-endpoint = <&adv7511_out>;
+ };
+ };
+ };
+
+ osc1_clk: osc1-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <148500000>;
+ };
+
+ osc4_clk: osc4-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ };
+};
+
+&du {
+ pinctrl-0 = <&du_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
+ <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
+ <&osc1_clk>;
+ clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1", "dclkin.0";
+
+ ports {
+ port@0 {
+ endpoint {
+ remote-endpoint = <&adv7511_in>;
+ };
+ };
+ port@1 {
+ lvds_connector0: endpoint {
+ };
+ };
+ port@2 {
+ lvds_connector1: endpoint {
+ };
+ };
+ };
+};
+
+&extal_clk {
+ clock-frequency = <20000000>;
+};
+
+&pfc {
+
+ pinctrl-0 = <&scif_clk_pins>;
+ pinctrl-names = "default";
+
+ du_pins: du {
+ groups = "du_rgb888", "du_sync_1", "du_clk_out_0";
+ function = "du";
+ };
+
+ scifa0_pins: scifa0 {
+ groups = "scifa0_data_b";
+ function = "scifa0";
+ };
+
+ scif_clk_pins: scif_clk {
+ groups = "scif_clk";
+ function = "scif_clk";
+ };
+
+ ether_pins: ether {
+ groups = "eth_link", "eth_mdio", "eth_rmii";
+ function = "eth";
+ };
+
+ phy1_pins: phy1 {
+ groups = "intc_irq1";
+ function = "intc";
+ };
+
+ sdhi0_pins: sd0 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ qspi_pins: qspi {
+ groups = "qspi_ctrl", "qspi_data4";
+ function = "qspi";
+ };
+
+ iic2_pins: iic2 {
+ groups = "iic2_b";
+ function = "iic2";
+ };
+
+ iic3_pins: iic3 {
+ groups = "iic3";
+ function = "iic3";
+ };
+
+ usb0_pins: usb0 {
+ groups = "usb0";
+ function = "usb0";
+ };
+};
+
+ðer {
+ pinctrl-0 = <ðer_pins &phy1_pins>;
+ pinctrl-names = "default";
+
+ phy-handle = <&phy1>;
+ renesas,ether-link-active-low;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ micrel,led-mode = <1>;
+ };
+};
+
+&cmt0 {
+ status = "okay";
+};
+
+&qspi {
+ pinctrl-0 = <&qspi_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ flash: flash@0 {
+ compatible = "spansion,s25fl512s", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <30000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ spi-cpha;
+ spi-cpol;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "loader";
+ reg = <0x00000000 0x00080000>;
+ read-only;
+ };
+ partition@80000 {
+ label = "uboot";
+ reg = <0x00080000 0x00040000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "uboot-env";
+ reg = <0x000c0000 0x00040000>;
+ read-only;
+ };
+ partition@100000 {
+ label = "flash";
+ reg = <0x00100000 0x03f00000>;
+ };
+ };
+ };
+};
+
+&scifa0 {
+ pinctrl-0 = <&scifa0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&scif_clk {
+ clock-frequency = <14745600>;
+};
+
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_dvfs>;
+};
+
+&iic2 {
+ status = "okay";
+ pinctrl-0 = <&iic2_pins>;
+ pinctrl-names = "default";
+
+ clock-frequency = <100000>;
+
+ hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&osc4_clk>;
+ clock-names = "cec";
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con_out>;
+ };
+ };
+ };
+ };
+};
+
+&iic3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&iic3_pins>;
+ status = "okay";
+
+ pmic@58 {
+ compatible = "dlg,da9063";
+ reg = <0x58>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ rtc {
+ compatible = "dlg,da9063-rtc";
+ };
+
+ wdt {
+ compatible = "dlg,da9063-watchdog";
+ };
+ };
+
+ vdd_dvfs: regulator@68 {
+ compatible = "dlg,da9210";
+ reg = <0x68>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd: regulator@70 {
+ compatible = "dlg,da9210";
+ reg = <0x70>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&pci0 {
+ status = "okay";
+ pinctrl-0 = <&usb0_pins>;
+ pinctrl-names = "default";
+};
+
+&usbphy {
+ status = "okay";
+};
Stout base board support making use of 1 GiB of memory, the Renesas H2 r8a7790 SoC with the SCIFA0 serial port and CA15 with ARM architected timer. Furthermore, this device tree contains entries for: - 4x LEDs - SDHI SD/MMC controller - Display unit with HDMI output - SH fast ethernet controller - QSPI controller with S25FL512S attached to it - I2C controller with DA9210 and DA 9063 PMICs Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> --- V2: - Fix LED polarity - Rename x2 to osc1 - Drop x13 - Add osc4 for hdmi cec - Drop dclkin.1 - Fix up SPI NOR partitioning - Use SPDX license tag V3: - Set serial port baudrate to 115200 --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/r8a7790-stout.dts | 363 ++++++++++++++++++++++++++++++++++++ 2 files changed, 364 insertions(+) create mode 100644 arch/arm/boot/dts/r8a7790-stout.dts