diff mbox series

[v6,08/12] serial: 8250: dw: Add support for DMA flow controlling devices

Message ID 20220421095323.101811-9-miquel.raynal@bootlin.com (mailing list archive)
State Superseded
Delegated to: Geert Uytterhoeven
Headers show
Series serial: 8250: dw: RZN1 DMA support | expand

Commit Message

Miquel Raynal April 21, 2022, 9:53 a.m. UTC 
From: Phil Edworthy <phil.edworthy@renesas.com>

DW based controllers like the one on Renesas RZ/N1 must be programmed as
flow controllers when using DMA.

* Table 11.45 of the system manual, "Flow Control Combinations", states
  that using UART with DMA requires setting the DMA in the peripheral
  flow controller mode regardless of the direction.

* Chapter 11.6.1.3 of the system manual, "Basic Interface Definitions",
  explains that the burst size in the above case must be configured in
  the peripheral's register DEST/SRC_BURST_SIZE.

Experiments shown that upon Rx timeout, the DMA transaction needed to be
manually cleared as well.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 drivers/tty/serial/8250/8250_dw.c | 64 +++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)
diff mbox series

Patch

diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index ef3f05c82ad6..90e64c8bd4bf 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -34,16 +34,28 @@ 
 
 /* Offsets for the DesignWare specific registers */
 #define DW_UART_USR	0x1f /* UART Status Register */
+#define DW_UART_DMASA	0xa8 /* DMA Software Ack */
 
 #define OCTEON_UART_USR	0x27 /* UART Status Register */
 
+#define RZN1_UART_TDMACR 0x10c /* DMA Control Register Transmit Mode */
+#define RZN1_UART_RDMACR 0x110 /* DMA Control Register Receive Mode */
+
 /* DesignWare specific register fields */
 #define DW_UART_MCR_SIRE		BIT(6)
 
+/* Renesas specific register fields */
+#define RZN1_UART_xDMACR_DMA_EN		BIT(0)
+#define RZN1_UART_xDMACR_1_WORD_BURST	(0 << 1)
+#define RZN1_UART_xDMACR_4_WORD_BURST	(1 << 1)
+#define RZN1_UART_xDMACR_8_WORD_BURST	(3 << 1)
+#define RZN1_UART_xDMACR_BLK_SZ(x)	((x) << 3)
+
 /* Quirks */
 #define DW_UART_QUIRK_OCTEON		BIT(0)
 #define DW_UART_QUIRK_ARMADA_38X	BIT(1)
 #define DW_UART_QUIRK_SKIP_SET_RATE	BIT(2)
+#define DW_UART_QUIRK_IS_DMA_FC		BIT(3)
 
 static inline struct dw8250_data *clk_to_dw8250_data(struct notifier_block *nb)
 {
@@ -226,6 +238,7 @@  static int dw8250_handle_irq(struct uart_port *p)
 	struct dw8250_data *d = to_dw8250_data(p->private_data);
 	unsigned int iir = p->serial_in(p, UART_IIR);
 	bool rx_timeout = (iir & 0x3f) == UART_IIR_RX_TIMEOUT;
+	unsigned int quirks = d->pdata->quirks;
 	unsigned int status;
 	unsigned long flags;
 
@@ -249,6 +262,15 @@  static int dw8250_handle_irq(struct uart_port *p)
 		spin_unlock_irqrestore(&p->lock, flags);
 	}
 
+	/* Manually stop the Rx DMA transfer when acting as flow controller */
+	if (quirks & DW_UART_QUIRK_IS_DMA_FC && up->dma && up->dma->rx_running && rx_timeout) {
+		status = p->serial_in(p, UART_LSR);
+		if (status & (UART_LSR_DR | UART_LSR_BI)) {
+			dw8250_writel_ext(p, RZN1_UART_RDMACR, 0);
+			dw8250_writel_ext(p, DW_UART_DMASA, 1);
+		}
+	}
+
 	if (serial8250_handle_irq(p, iir))
 		return 1;
 
@@ -372,6 +394,42 @@  static bool dw8250_idma_filter(struct dma_chan *chan, void *param)
 	return param == chan->device->dev;
 }
 
+static u32 dw8250_rzn1_get_dmacr_burst(int max_burst)
+{
+	if (max_burst >= 8)
+		return RZN1_UART_xDMACR_8_WORD_BURST;
+	else if (max_burst >= 4)
+		return RZN1_UART_xDMACR_4_WORD_BURST;
+	else
+		return RZN1_UART_xDMACR_1_WORD_BURST;
+}
+
+static void dw8250_prepare_tx_dma(struct uart_8250_port *p)
+{
+	struct uart_port *up = &p->port;
+	struct uart_8250_dma *dma = p->dma;
+	u32 val;
+
+	dw8250_writel_ext(up, RZN1_UART_TDMACR, 0);
+	val = dw8250_rzn1_get_dmacr_burst(dma->txconf.dst_maxburst) |
+	      RZN1_UART_xDMACR_BLK_SZ(dma->tx_size) |
+	      RZN1_UART_xDMACR_DMA_EN;
+	dw8250_writel_ext(up, RZN1_UART_TDMACR, val);
+}
+
+static void dw8250_prepare_rx_dma(struct uart_8250_port *p)
+{
+	struct uart_port *up = &p->port;
+	struct uart_8250_dma *dma = p->dma;
+	u32 val;
+
+	dw8250_writel_ext(up, RZN1_UART_RDMACR, 0);
+	val = dw8250_rzn1_get_dmacr_burst(dma->rxconf.src_maxburst) |
+	      RZN1_UART_xDMACR_BLK_SZ(dma->rx_size) |
+	      RZN1_UART_xDMACR_DMA_EN;
+	dw8250_writel_ext(up, RZN1_UART_RDMACR, val);
+}
+
 static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
 {
 	struct device_node *np = p->dev->of_node;
@@ -404,6 +462,12 @@  static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
 			p->serial_out = dw8250_serial_out38x;
 		if (quirks & DW_UART_QUIRK_SKIP_SET_RATE)
 			p->set_termios = dw8250_do_set_termios;
+		if (quirks & DW_UART_QUIRK_IS_DMA_FC) {
+			data->data.dma.txconf.device_fc = 1;
+			data->data.dma.rxconf.device_fc = 1;
+			data->data.dma.prepare_tx_dma = dw8250_prepare_tx_dma;
+			data->data.dma.prepare_rx_dma = dw8250_prepare_rx_dma;
+		}
 
 	} else if (acpi_dev_present("APMC0D08", NULL, -1)) {
 		p->iotype = UPIO_MEM32;