deleted file mode 100644
@@ -1,84 +0,0 @@
-Renesas AHB to PCI bridge
--------------------------
-
-This is the bridge used internally to connect the USB controllers to the
-AHB. There is one bridge instance per USB port connected to the internal
-OHCI and EHCI controllers.
-
-Required properties:
-- compatible: "renesas,pci-r8a7742" for the R8A7742 SoC;
- "renesas,pci-r8a7743" for the R8A7743 SoC;
- "renesas,pci-r8a7744" for the R8A7744 SoC;
- "renesas,pci-r8a7745" for the R8A7745 SoC;
- "renesas,pci-r8a7790" for the R8A7790 SoC;
- "renesas,pci-r8a7791" for the R8A7791 SoC;
- "renesas,pci-r8a7793" for the R8A7793 SoC;
- "renesas,pci-r8a7794" for the R8A7794 SoC;
- "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or
- RZ/G1 compatible device.
-
-
- When compatible with the generic version, nodes must list the
- SoC-specific version corresponding to the platform first
- followed by the generic version.
-
-- reg: A list of physical regions to access the device: the first is
- the operational registers for the OHCI/EHCI controllers and the
- second is for the bridge configuration and control registers.
-- interrupts: interrupt for the device.
-- clocks: The reference to the device clock.
-- bus-range: The PCI bus number range; as this is a single bus, the range
- should be specified as the same value twice.
-- #address-cells: must be 3.
-- #size-cells: must be 2.
-- #interrupt-cells: must be 1.
-- interrupt-map: standard property used to define the mapping of the PCI
- interrupts to the GIC interrupts.
-- interrupt-map-mask: standard property that helps to define the interrupt
- mapping.
-
-Optional properties:
-- dma-ranges: a single range for the inbound memory region. If not supplied,
- defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the
- allowed combinations of address and size.
-
-Example SoC configuration:
-
- pci0: pci@ee090000 {
- compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2";
- clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
- reg = <0x0 0xee090000 0x0 0xc00>,
- <0x0 0xee080000 0x0 0x1100>;
- interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
-
- bus-range = <0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>;
- interrupt-map-mask = <0xff00 0 0 0x7>;
- interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
- 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
- 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>;
-
- usb@1,0 {
- reg = <0x800 0 0 0 0>;
- phys = <&usb0 0>;
- phy-names = "usb";
- };
-
- usb@2,0 {
- reg = <0x1000 0 0 0 0>;
- phys = <&usb0 0>;
- phy-names = "usb";
- };
- };
-
-Example board setup:
-
-&pci0 {
- status = "okay";
- pinctrl-0 = <&usb0_pins>;
- pinctrl-names = "default";
-};
new file mode 100644
@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/renesas,pci-rcar-gen2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas AHB to PCI bridge
+
+maintainers:
+ - Marek Vasut <marek.vasut+renesas@gmail.com>
+ - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
+
+description: |
+ This is the bridge used internally to connect the USB controllers to the
+ AHB. There is one bridge instance per USB port connected to the internal
+ OHCI and EHCI controllers.
+
+allOf:
+ - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - renesas,pci-r8a7742 # RZ/G1H
+ - renesas,pci-r8a7743 # RZ/G1M
+ - renesas,pci-r8a7744 # RZ/G1N
+ - renesas,pci-r8a7745 # RZ/G1E
+ - renesas,pci-r8a7790 # R-Car H2
+ - renesas,pci-r8a7791 # R-Car M2-W
+ - renesas,pci-r8a7793 # R-Car M2-N
+ - renesas,pci-r8a7794 # R-Car E2
+ - const: renesas,pci-rcar-gen2 # R-Car Gen2 and RZ/G1
+
+ reg:
+ items:
+ - description: Operational registers for the OHCI/EHCI controllers.
+ - description: Bridge configuration and control registers.
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Device clock
+
+ clock-names:
+ items:
+ - const: pclk
+
+ resets:
+ maxItems: 1
+
+ power-domains:
+ maxItems: 1
+
+ bus-range:
+ description: |
+ The PCI bus number range; as this is a single bus, the range
+ should be specified as the same value twice.
+
+ dma-ranges:
+ description: |
+ A single range for the inbound memory region. If not supplied,
+ defaults to 1GiB at 0x40000000. Note there are hardware restrictions on
+ the allowed combinations of address and size.
+ maxItems: 1
+
+patternProperties:
+ 'usb@[0-1],0':
+ type: object
+
+ description:
+ This a USB controller PCI device
+
+ properties:
+ reg:
+ description:
+ Identify the correct bus, device and function number in the
+ form <bdf 0 0 0 0>.
+
+ items:
+ minItems: 5
+ maxItems: 5
+
+ phys:
+ description:
+ Reference to the USB phy
+ maxItems: 1
+
+ phy-names:
+ maxItems: 1
+
+ required:
+ - reg
+ - phys
+ - phy-names
+
+ unevaluatedProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-map
+ - interrupt-map-mask
+ - clocks
+ - resets
+ - power-domains
+ - bus-range
+ - "#address-cells"
+ - "#size-cells"
+ - "#interrupt-cells"
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/r8a7790-cpg-mssr.h>
+ #include <dt-bindings/power/r8a7790-sysc.h>
+
+ pci@ee090000 {
+ compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2";
+ device_type = "pci";
+ reg = <0xee090000 0xc00>,
+ <0xee080000 0x1100>;
+ clocks = <&cpg CPG_MOD 703>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+ resets = <&cpg 703>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+
+ bus-range = <0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x02000000 0 0xee080000 0xee080000 0 0x00010000>;
+ dma-ranges = <0x42000000 0 0x40000000 0x40000000 0 0x40000000>;
+ interrupt-map-mask = <0xf800 0 0 0x7>;
+ interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+
+ usb@1,0 {
+ reg = <0x800 0 0 0 0>;
+ phys = <&usb0 0>;
+ phy-names = "usb";
+ };
+
+ usb@2,0 {
+ reg = <0x1000 0 0 0 0>;
+ phys = <&usb0 0>;
+ phy-names = "usb";
+ };
+ };