| Message ID | 20240918120909.284930-3-prabhakar.mahadev-lad.rj@bp.renesas.com (mailing list archive) |
|---|---|
| State | Superseded |
| Delegated to: | Geert Uytterhoeven |
| Headers | show |
| Series | pinctrl: renesas: rzg2l: Add support to configure open-drain and schmitt-trigger properties | expand |
Hi Prabhakar, On Wed, Sep 18, 2024 at 2:09 PM Prabhakar <prabhakar.csengg@gmail.com> wrote: > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > Add support for configuring the multiplexed pins as open-drain outputs. > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Thanks for your patch! > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c > @@ -1466,6 +1477,13 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev, > rzg2l_rmw_pin_config(pctrl, IOLH(off), bit, IOLH_MASK, index); > break; > > + case PIN_CONFIG_DRIVE_OPEN_DRAIN: > + if (!(cfg & PIN_CFG_NOD)) > + return -EINVAL; > + > + rzg2l_rmw_pin_config(pctrl, NOD(off), bit, NOD_MASK, 1); > + break; > + I think you also need a case for PIN_CONFIG_DRIVE_PUSH_PULL, so you can disable the NOD bit again. > case RENESAS_RZV2H_PIN_CONFIG_OUTPUT_IMPEDANCE: > if (!(cfg & PIN_CFG_IOLH_RZV2H)) > return -EINVAL; Gr{oetje,eeting}s, Geert
Hi Geert, Thank you for the review. On Fri, Oct 4, 2024 at 8:56 AM Geert Uytterhoeven <geert@linux-m68k.org> wrote: > > Hi Prabhakar, > > On Wed, Sep 18, 2024 at 2:09 PM Prabhakar <prabhakar.csengg@gmail.com> wrote: > > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > > > Add support for configuring the multiplexed pins as open-drain outputs. > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > Thanks for your patch! > > > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c > > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c > > > @@ -1466,6 +1477,13 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev, > > rzg2l_rmw_pin_config(pctrl, IOLH(off), bit, IOLH_MASK, index); > > break; > > > > + case PIN_CONFIG_DRIVE_OPEN_DRAIN: > > + if (!(cfg & PIN_CFG_NOD)) > > + return -EINVAL; > > + > > + rzg2l_rmw_pin_config(pctrl, NOD(off), bit, NOD_MASK, 1); > > + break; > > + > > I think you also need a case for PIN_CONFIG_DRIVE_PUSH_PULL, > so you can disable the NOD bit again. > Ok, I will implement PIN_CONFIG_DRIVE_PUSH_PULL to disable open drain and send a v2. Cheers, Prabhakar
diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c index 5a403915fed2..42181cc877fe 100644 --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c @@ -139,6 +139,7 @@ #define IEN(off) (0x1800 + (off) * 8) #define PUPD(off) (0x1C00 + (off) * 8) #define ISEL(off) (0x2C00 + (off) * 8) +#define NOD(off) (0x3000 + (off) * 8) #define SD_CH(off, ch) ((off) + (ch) * 4) #define ETH_POC(off, ch) ((off) + (ch) * 4) #define QSPI (0x3008) @@ -160,6 +161,7 @@ #define IOLH_MASK 0x03 #define SR_MASK 0x01 #define PUPD_MASK 0x03 +#define NOD_MASK 0x01 #define PM_INPUT 0x1 #define PM_OUTPUT 0x2 @@ -1337,6 +1339,15 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev, break; } + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + if (!(cfg & PIN_CFG_NOD)) + return -EINVAL; + + arg = rzg2l_read_pin_config(pctrl, NOD(off), bit, NOD_MASK); + if (!arg) + return -EINVAL; + break; + case RENESAS_RZV2H_PIN_CONFIG_OUTPUT_IMPEDANCE: if (!(cfg & PIN_CFG_IOLH_RZV2H)) return -EINVAL; @@ -1466,6 +1477,13 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev, rzg2l_rmw_pin_config(pctrl, IOLH(off), bit, IOLH_MASK, index); break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + if (!(cfg & PIN_CFG_NOD)) + return -EINVAL; + + rzg2l_rmw_pin_config(pctrl, NOD(off), bit, NOD_MASK, 1); + break; + case RENESAS_RZV2H_PIN_CONFIG_OUTPUT_IMPEDANCE: if (!(cfg & PIN_CFG_IOLH_RZV2H)) return -EINVAL;