@@ -71,10 +71,7 @@ struct rcar_csi2;
#define FLD_REG 0x1c
#define FLD_FLD_NUM(n) (((n) & 0xff) << 16)
#define FLD_DET_SEL(n) (((n) & 0x3) << 4)
-#define FLD_FLD_EN4 BIT(3)
-#define FLD_FLD_EN3 BIT(2)
-#define FLD_FLD_EN2 BIT(1)
-#define FLD_FLD_EN BIT(0)
+#define FLD_FLD_EN(ch) BIT(ch)
/* Automatic Standby Control */
#define ASTBY_REG 0x20
@@ -1062,52 +1059,94 @@ static int rcsi2_calc_mbps(struct rcar_csi2 *priv,
static int rcsi2_start_receiver_gen3(struct rcar_csi2 *priv,
struct v4l2_subdev_state *state)
{
- const struct rcar_csi2_format *format;
- u32 phycnt, vcdt = 0, vcdt2 = 0, fld = 0;
- const struct v4l2_mbus_framefmt *fmt;
+ u32 phycnt, vcdt = 0, vcdt2 = 0;
+ u32 fld = FLD_DET_SEL(1);
+ struct v4l2_mbus_frame_desc source_fd;
+ struct v4l2_subdev_route *route;
unsigned int lanes;
- unsigned int i;
int mbps, ret;
+ u8 ch = 0;
- /* Use the format on the sink pad to compute the receiver config. */
- fmt = v4l2_subdev_state_get_format(state, RCAR_CSI2_SINK, 0);
+ ret = v4l2_subdev_call(priv->remote, pad, get_frame_desc,
+ priv->remote_pad, &source_fd);
+ if (ret && ret != -ENOIOCTLCMD) {
+ return ret;
+ } else if (ret == -ENOIOCTLCMD) {
+ /* Create a fallback source_fd */
+ struct v4l2_mbus_frame_desc *fd = &source_fd;
+ const struct rcar_csi2_format *format;
+ struct v4l2_mbus_framefmt *fmt;
- dev_dbg(priv->dev, "Input size (%ux%u%c)\n",
- fmt->width, fmt->height,
- fmt->field == V4L2_FIELD_NONE ? 'p' : 'i');
+ fmt = v4l2_subdev_state_get_format(state, RCAR_CSI2_SINK, 0);
+ if (!fmt)
+ return -EINVAL;
- /* Code is validated in set_fmt. */
- format = rcsi2_code_to_fmt(fmt->code);
- if (!format)
- return -EINVAL;
+ format = rcsi2_code_to_fmt(fmt->code);
+ if (!format)
+ return -EINVAL;
- /*
- * Enable all supported CSI-2 channels with virtual channel and
- * data type matching.
- *
- * NOTE: It's not possible to get individual datatype for each
- * source virtual channel. Once this is possible in V4L2
- * it should be used here.
- */
- for (i = 0; i < priv->info->num_channels; i++) {
+ memset(fd, 0, sizeof(*fd));
+
+ fd->num_entries = 1;
+ fd->type = V4L2_MBUS_FRAME_DESC_TYPE_CSI2;
+ fd->entry[0].stream = 0;
+ fd->entry[0].pixelcode = fmt->code;
+ fd->entry[0].bus.csi2.vc = 0;
+ fd->entry[0].bus.csi2.dt = format->datatype;
+ }
+
+ for_each_active_route(&state->routing, route) {
+ struct v4l2_mbus_frame_desc_entry *source_entry = NULL;
+ const struct v4l2_mbus_framefmt *fmt;
+ const struct rcar_csi2_format *format;
+ unsigned int i;
+ u8 vc, dt;
u32 vcdt_part;
- if (priv->channel_vc[i] < 0)
- continue;
+ for (i = 0; i < source_fd.num_entries; i++) {
+ if (source_fd.entry[i].stream == route->sink_stream) {
+ source_entry = &source_fd.entry[i];
+ break;
+ }
+ }
+
+ if (!source_entry) {
+ dev_err(priv->dev,
+ "Failed to find stream from source frame desc\n");
+ return -EPIPE;
+ }
- vcdt_part = VCDT_SEL_VC(priv->channel_vc[i]) | VCDT_VCDTN_EN |
- VCDT_SEL_DTN_ON | VCDT_SEL_DT(format->datatype);
+ vc = source_entry->bus.csi2.vc;
+ dt = source_entry->bus.csi2.dt;
+
+ vcdt_part = VCDT_SEL_VC(vc) | VCDT_VCDTN_EN |
+ VCDT_SEL_DTN_ON | VCDT_SEL_DT(dt);
/* Store in correct reg and offset. */
- if (i < 2)
- vcdt |= vcdt_part << ((i % 2) * 16);
+ if (ch < 2)
+ vcdt |= vcdt_part << ((ch % 2) * 16);
else
- vcdt2 |= vcdt_part << ((i % 2) * 16);
- }
+ vcdt2 |= vcdt_part << ((ch % 2) * 16);
+
+ fmt = v4l2_subdev_state_get_format(state, RCAR_CSI2_SINK,
+ route->sink_stream);
+ if (!fmt)
+ return -EINVAL;
+
+ dev_dbg(priv->dev, "Input size (%ux%u%c)\n",
+ fmt->width, fmt->height,
+ fmt->field == V4L2_FIELD_NONE ? 'p' : 'i');
- if (fmt->field == V4L2_FIELD_ALTERNATE)
- fld = FLD_DET_SEL(1) | FLD_FLD_EN4 | FLD_FLD_EN3 | FLD_FLD_EN2
- | FLD_FLD_EN;
+ /* Code is validated in set_fmt. */
+ format = rcsi2_code_to_fmt(fmt->code);
+ if (!format)
+ return -EINVAL;
+
+ if (fmt->field == V4L2_FIELD_ALTERNATE)
+ fld |= FLD_FLD_EN(ch);
+
+ ch++;
+ }
/*
* Get the number of active data lanes inspecting the remote mbus
Call get_frame_desc to find out VC & DT, for Gen3 platforms, instead of hardcoding the VC routing and deducing the DT based on the mbus format. If the source subdevice doesn't implement .get_frame_desc, we use a fallback case where we assume there's a single stream with VC = 0 and DT based on the mbus format. Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com> --- drivers/media/platform/renesas/rcar-csi2.c | 113 +++++++++++++++++++---------- 1 file changed, 76 insertions(+), 37 deletions(-)