@@ -92,6 +92,7 @@ source "drivers/phy/renesas/Kconfig"
source "drivers/phy/rockchip/Kconfig"
source "drivers/phy/samsung/Kconfig"
source "drivers/phy/socionext/Kconfig"
+source "drivers/phy/sophgo/Kconfig"
source "drivers/phy/st/Kconfig"
source "drivers/phy/starfive/Kconfig"
source "drivers/phy/sunplus/Kconfig"
@@ -31,6 +31,7 @@ obj-y += allwinner/ \
rockchip/ \
samsung/ \
socionext/ \
+ sophgo/ \
st/ \
starfive/ \
sunplus/ \
new file mode 100644
@@ -0,0 +1,19 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Phy drivers for Sophgo platforms
+#
+
+if ARCH_SOPHGO || COMPILE_TEST
+
+config PHY_SOPHGO_CV1800_USB
+ tristate "Sophgo CV18XX/SG200X USB 2.0 PHY support"
+ depends on MFD_SYSCON
+ depends on USB_SUPPORT
+ select GENERIC_PHY
+ help
+ Enable this to support the USB 2.0 PHY used with
+ the DWC2 USB controller in Sophgo CV18XX/SG200X
+ series SoC.
+ If unsure, say N.
+
+endif # ARCH_SOPHGO || COMPILE_TEST
new file mode 100644
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_PHY_SOPHGO_CV1800_USB) += phy-cv1800-usb.o
new file mode 100644
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/debugfs.h>
+#include <linux/gpio/consumer.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/spinlock.h>
+#include <soc/sophgo/cv1800-sysctl.h>
+
+#define PHY_IDPAD_C_OW BIT(6)
+#define PHY_IDPAD_C_SW BIT(7)
+
+#define PHY_BASE_CLK_RATE 300000000
+#define PHY_APP_CLK_RATE 125000000
+#define PHY_LPM_CLK_RATE 12000000
+#define PHY_STB_CLK_RATE 333334
+
+#define PHY_VBUS_DET_DEBOUNCE_TIME usecs_to_jiffies(100)
+
+struct cv1800_usb_phy {
+ struct phy *phy;
+ struct regmap *syscon;
+ spinlock_t lock;
+ struct clk *usb_phy_clk;
+ struct clk *usb_app_clk;
+ struct clk *usb_lpm_clk;
+ struct clk *usb_stb_clk;
+ struct gpio_descs *switch_gpios;
+ struct gpio_desc *vbus_det_gpio;
+ int vbus_det_irq;
+ struct delayed_work vbus_work;
+ bool enable_otg;
+};
+
+static int cv1800_usb_phy_set_idpad(struct cv1800_usb_phy *phy,
+ bool is_host)
+{
+ unsigned long flags;
+ unsigned int regval = 0;
+ int ret;
+
+ if (is_host)
+ regval = PHY_IDPAD_C_OW;
+ else
+ regval = PHY_IDPAD_C_OW | PHY_IDPAD_C_SW;
+
+ spin_lock_irqsave(&phy->lock, flags);
+ ret = regmap_update_bits(phy->syscon, CV1800_USB_PHY_CTRL_REG,
+ PHY_IDPAD_C_OW | PHY_IDPAD_C_SW,
+ regval);
+ spin_unlock_irqrestore(&phy->lock, flags);
+
+ return ret;
+}
+
+static void cv1800_usb_phy_set_gpio(struct cv1800_usb_phy *phy,
+ bool is_host)
+{
+ unsigned int i, ndescs;
+ struct gpio_desc **gpios;
+
+ if (!phy->switch_gpios)
+ return;
+
+ ndescs = phy->switch_gpios->ndescs;
+ gpios = phy->switch_gpios->desc;
+
+ if (is_host) {
+ for (i = 0; i < ndescs; i++)
+ gpiod_set_value_cansleep(gpios[i], 0);
+ } else {
+ for (i = 0; i < ndescs; i++)
+ gpiod_set_value_cansleep(gpios[ndescs - 1 - i], 1);
+ }
+}
+
+static int cv1800_usb_phy_set_mode_internal(struct cv1800_usb_phy *phy,
+ bool is_host)
+{
+ int ret = cv1800_usb_phy_set_idpad(phy, is_host);
+
+ if (ret < 0)
+ return ret;
+
+ cv1800_usb_phy_set_gpio(phy, is_host);
+
+ return 0;
+}
+
+static ssize_t dr_mode_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t len)
+{
+ struct cv1800_usb_phy *phy = dev_get_drvdata(dev);
+ bool is_host;
+
+ if (sysfs_streq(buf, "host")) {
+ phy->enable_otg = false;
+ is_host = true;
+ } else if (sysfs_streq(buf, "peripheral")) {
+ phy->enable_otg = false;
+ is_host = false;
+ } else if (sysfs_streq(buf, "otg") && phy->vbus_det_irq > 0) {
+ phy->enable_otg = true;
+ } else {
+ return -EINVAL;
+ }
+
+ if (phy->enable_otg)
+ queue_delayed_work(system_wq, &phy->vbus_work,
+ PHY_VBUS_DET_DEBOUNCE_TIME);
+ else
+ cv1800_usb_phy_set_mode_internal(phy, is_host);
+
+ return len;
+}
+
+static ssize_t dr_mode_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct cv1800_usb_phy *phy = dev_get_drvdata(dev);
+ unsigned long flags;
+ unsigned int regval;
+ bool is_host = true;
+ int ret;
+
+ spin_lock_irqsave(&phy->lock, flags);
+ ret = regmap_read(phy->syscon, CV1800_USB_PHY_CTRL_REG, ®val);
+ spin_unlock_irqrestore(&phy->lock, flags);
+
+ if (ret)
+ return ret;
+
+ if (regval & PHY_IDPAD_C_SW)
+ is_host = false;
+
+ return sprintf(buf, "%s%s\n",
+ phy->enable_otg ? "otg: " : "",
+ is_host ? "host" : "peripheral");
+}
+
+static DEVICE_ATTR_RW(dr_mode);
+
+static struct attribute *cv1800_usb_phy_attrs[] = {
+ &dev_attr_dr_mode.attr,
+ NULL
+};
+
+static const struct attribute_group cv1800_usb_phy_group = {
+ .attrs = cv1800_usb_phy_attrs,
+};
+
+static int cv1800_usb_phy_set_clock(struct cv1800_usb_phy *phy)
+{
+ int ret;
+
+ ret = clk_set_rate(phy->usb_phy_clk, PHY_BASE_CLK_RATE);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(phy->usb_app_clk, PHY_APP_CLK_RATE);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(phy->usb_lpm_clk, PHY_LPM_CLK_RATE);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(phy->usb_stb_clk, PHY_STB_CLK_RATE);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int cv1800_usb_phy_set_mode(struct phy *_phy,
+ enum phy_mode mode, int submode)
+{
+ struct cv1800_usb_phy *phy = phy_get_drvdata(_phy);
+ bool is_host;
+
+ switch (mode) {
+ case PHY_MODE_USB_DEVICE:
+ is_host = false;
+ phy->enable_otg = false;
+ break;
+ case PHY_MODE_USB_HOST:
+ is_host = true;
+ phy->enable_otg = false;
+ break;
+ case PHY_MODE_USB_OTG:
+ /* phy only supports soft OTG when VBUS_DET pin is connected. */
+ if (phy->vbus_det_irq > 0) {
+ phy->enable_otg = true;
+ queue_delayed_work(system_wq, &phy->vbus_work,
+ PHY_VBUS_DET_DEBOUNCE_TIME);
+ }
+ return 0;
+ default:
+ return -EINVAL;
+ }
+
+ return cv1800_usb_phy_set_mode_internal(phy, is_host);
+}
+
+static const struct phy_ops cv1800_usb_phy_ops = {
+ .set_mode = cv1800_usb_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static void cv1800_usb_phy_vbus_switch(struct work_struct *work)
+{
+ struct cv1800_usb_phy *phy =
+ container_of(work, struct cv1800_usb_phy, vbus_work.work);
+ int state = gpiod_get_value_cansleep(phy->vbus_det_gpio);
+
+ cv1800_usb_phy_set_mode_internal(phy, state == 0);
+}
+
+static irqreturn_t cv1800_usb_phy_vbus_det_irq(int irq, void *dev_id)
+{
+ struct cv1800_usb_phy *phy = dev_id;
+
+ if (phy->enable_otg)
+ queue_delayed_work(system_wq, &phy->vbus_work,
+ PHY_VBUS_DET_DEBOUNCE_TIME);
+ return IRQ_HANDLED;
+}
+
+static void cv1800_usb_phy_init_mode(struct device *dev,
+ struct cv1800_usb_phy *phy)
+{
+ phy->enable_otg = false;
+
+ if (phy->vbus_det_irq > 0)
+ phy->enable_otg = true;
+
+ if (phy->enable_otg)
+ queue_delayed_work(system_wq, &phy->vbus_work, 0);
+ else
+ cv1800_usb_phy_set_mode_internal(phy, true);
+}
+
+static int cv1800_usb_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device *parent = dev->parent;
+ struct cv1800_usb_phy *phy;
+ struct phy_provider *phy_provider;
+ int ret;
+
+ if (!parent)
+ return -ENODEV;
+
+ phy = devm_kmalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->syscon = syscon_node_to_regmap(parent->of_node);
+ if (IS_ERR_OR_NULL(phy->syscon))
+ return -ENODEV;
+
+ spin_lock_init(&phy->lock);
+
+ phy->usb_phy_clk = devm_clk_get_enabled(dev, "phy");
+ if (IS_ERR(phy->usb_phy_clk))
+ return dev_err_probe(dev, PTR_ERR(phy->usb_phy_clk),
+ "Failed to get phy clock\n");
+
+ phy->usb_app_clk = devm_clk_get_enabled(dev, "app");
+ if (IS_ERR(phy->usb_app_clk))
+ return dev_err_probe(dev, PTR_ERR(phy->usb_app_clk),
+ "Failed to get app clock\n");
+
+ phy->usb_lpm_clk = devm_clk_get_enabled(dev, "lpm");
+ if (IS_ERR(phy->usb_lpm_clk))
+ return dev_err_probe(dev, PTR_ERR(phy->usb_lpm_clk),
+ "Failed to get lpm clock\n");
+
+ phy->usb_stb_clk = devm_clk_get_enabled(dev, "stb");
+ if (IS_ERR(phy->usb_stb_clk))
+ return dev_err_probe(dev, PTR_ERR(phy->usb_stb_clk),
+ "Failed to get stb clock\n");
+
+ phy->phy = devm_phy_create(dev, NULL, &cv1800_usb_phy_ops);
+ if (IS_ERR(phy->phy))
+ return dev_err_probe(dev, PTR_ERR(phy->phy),
+ "Failed to create phy\n");
+
+ ret = cv1800_usb_phy_set_clock(phy);
+ if (ret)
+ return ret;
+
+ phy->switch_gpios = devm_gpiod_get_array_optional(dev, "sophgo,switch",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(phy->switch_gpios))
+ return dev_err_probe(dev, PTR_ERR(phy->switch_gpios),
+ "Failed to get switch pin\n");
+
+ phy->vbus_det_gpio = devm_gpiod_get_optional(dev, "vbus_det", GPIOD_IN);
+ if (IS_ERR(phy->vbus_det_gpio))
+ return dev_err_probe(dev, PTR_ERR(phy->vbus_det_gpio),
+ "Failed to process vbus pin\n");
+
+ phy->vbus_det_irq = gpiod_to_irq(phy->vbus_det_gpio);
+ if (phy->vbus_det_irq > 0) {
+ ret = devm_request_irq(dev, phy->vbus_det_irq,
+ cv1800_usb_phy_vbus_det_irq,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "usb-vbus-det", phy);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Failed to request vbus irq\n");
+ }
+
+ INIT_DELAYED_WORK(&phy->vbus_work, cv1800_usb_phy_vbus_switch);
+
+ ret = sysfs_create_group(&dev->kobj, &cv1800_usb_phy_group);
+ if (ret)
+ dev_warn(dev, "failed to create sysfs attributes\n");
+
+ phy_set_drvdata(phy->phy, phy);
+ platform_set_drvdata(pdev, phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ /*
+ * phy needs to change mode twice after initialization,
+ * otherwise the controller can not found devices attached
+ * to the phy.
+ */
+ cv1800_usb_phy_set_idpad(phy, false);
+ cv1800_usb_phy_set_idpad(phy, true);
+ cv1800_usb_phy_init_mode(dev, phy);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static void cv1800_usb_phy_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct cv1800_usb_phy *phy = platform_get_drvdata(pdev);
+
+ if (phy->vbus_det_irq > 0)
+ devm_free_irq(dev, phy->vbus_det_irq, phy);
+
+ cancel_delayed_work_sync(&phy->vbus_work);
+}
+
+static const struct of_device_id cv1800_usb_phy_ids[] = {
+ { .compatible = "sophgo,cv1800-usb-phy" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, cv1800_usb_phy_ids);
+
+static struct platform_driver cv1800_usb_phy_driver = {
+ .probe = cv1800_usb_phy_probe,
+ .remove_new = cv1800_usb_phy_remove,
+ .driver = {
+ .name = "cv1800-usb-phy",
+ .of_match_table = cv1800_usb_phy_ids,
+ },
+};
+module_platform_driver(cv1800_usb_phy_driver);
+MODULE_DESCRIPTION("CV1800/SG2000 SoC USB 2.0 PHY driver");
+MODULE_LICENSE("GPL");
Add USB 2.0 PHY driver for Sophgo CV18XX/SG200X. Signed-off-by: Inochi Amaoto <inochiama@outlook.com> --- drivers/phy/Kconfig | 1 + drivers/phy/Makefile | 1 + drivers/phy/sophgo/Kconfig | 19 ++ drivers/phy/sophgo/Makefile | 2 + drivers/phy/sophgo/phy-cv1800-usb.c | 378 ++++++++++++++++++++++++++++ 5 files changed, 401 insertions(+) create mode 100644 drivers/phy/sophgo/Kconfig create mode 100644 drivers/phy/sophgo/Makefile create mode 100644 drivers/phy/sophgo/phy-cv1800-usb.c -- 2.45.0