@@ -146,6 +146,7 @@ struct rockchip_drv {
* @irq_lock: bus lock for irq chip
* @new_irqs: newly configured irqs which must be muxed as GPIOs in
* irq_bus_sync_unlock()
+ * @route_mask: bits describing the routing pins of per bank
*/
struct rockchip_pin_bank {
void __iomem *reg_base;
@@ -170,6 +171,7 @@ struct rockchip_pin_bank {
u32 toggle_edge_mode;
struct mutex irq_lock;
u32 new_irqs;
+ u32 route_mask;
};
#define PIN_BANK(id, pins, label) \
@@ -316,6 +318,8 @@ struct rockchip_pin_ctrl {
int (*schmitt_calc_reg)(struct rockchip_pin_bank *bank,
int pin_num, struct regmap **regmap,
int *reg, u8 *bit);
+ bool (*iomux_route)(u8 bank_num, int pin, int mux,
+ u32 *reg, u32 *value);
};
struct rockchip_pin_config {
@@ -383,6 +387,22 @@ struct rockchip_mux_recalced_data {
u8 mask;
};
+/**
+ * struct rockchip_mux_recalced_data: represent a pin iomux data.
+ * @bank: bank number.
+ * @pin: index at register or used to calc index.
+ * @func: the min pin.
+ * @route_offset: the max pin.
+ * @route_val: the register offset.
+ */
+struct rockchip_mux_route_data {
+ u8 bank;
+ u8 pin;
+ u8 func;
+ u32 route_offset;
+ u32 route_val;
+};
+
static struct regmap_config rockchip_regmap_config = {
.reg_bits = 32,
.val_bits = 32,
@@ -683,7 +703,7 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
struct regmap *regmap;
int reg, ret, mask, mux_type;
u8 bit;
- u32 data, rmask;
+ u32 data, rmask, route_reg, route_val;
ret = rockchip_verify_mux(bank, pin, mux);
if (ret < 0)
@@ -719,6 +739,15 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
if (ctrl->iomux_recalc && (mux_type & IOMUX_RECALCED))
ctrl->iomux_recalc(bank->bank_num, pin, ®, &bit, &mask);
+ if (ctrl->iomux_route && (bank->route_mask & BIT(pin))) {
+ if (ctrl->iomux_route(bank->bank_num, pin, mux,
+ &route_reg, &route_val)) {
+ ret = regmap_write(regmap, route_reg, route_val);
+ if (ret)
+ return ret;
+ }
+ }
+
data = (mask << (bit + 16));
rmask = data | (data >> 16);
data |= (mux & mask) << bit;
On the some rockchip soc, some things like one specific uart can use multiple pins, but control of that seems to be split. Somewhere between the pin io-cells and the uart it seems to have some sort of switch to decide to which pin to actually route the data. +-------+ +--------+ /- GPIO4_B0 (pinmux 2) | uart2 | -- | switch | --- GPIO4_C0 (pinmux 2) +-------+ +--------+ \- GPIO4_C3 (pinmux 2) (switch selects one of the 3 pins base on the GRF_SOC_CON7[BIT0, BIT1]) The routing switch is determined by one pin of a specific group to be set to its special pinmux function. If the pinmux setting is wrong for that pin the ip block won't work correctly anyway. Signed-off-by: David Wu <david.wu@rock-chips.com> --- drivers/pinctrl/pinctrl-rockchip.c | 31 ++++++++++++++++++++++++++++++- 1 file changed, 30 insertions(+), 1 deletion(-)