| Message ID | 20240712164554.1763-1-linux.amoon@gmail.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | [PATCH-next,v3,1/3] arm64: dts: rockchip: Add missing pinctrl for PCIe30x4 node | expand |
Hi Jonas, On Fri, 12 Jul 2024 at 22:16, Anand Moon <linux.amoon@gmail.com> wrote: > > Add missing pinctrl settings for PCIe 3.0 x4 clock request and wake > signals. Each component of PCIe communication have the following control > signals: PERST, WAKE, CLKREQ, and REFCLK. These signals work to generate > high-speed signals and communicate with other PCIe devices. > Used by root complex to endpoint depending on the power state. > > PERST is referred to as a fundamental reset. PERST should be held low > until all the power rails in the system and the reference clock are stable. > A transition from low to high in this signal usually indicates the > beginning of link initialization. > > WAKE signal is an active-low signal that is used to return the PCIe > interface to an active state when in a low-power state. > > CLKREQ signal is also an active-low signal and is used to request the > reference clock. > > Rename node from 'pcie3' to 'pcie30x4' to align with schematic > nomenclature. > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > --- > V3: use pinctrl local to board > V2: Update the commit messge to describe the changs. > use pinctl group as its pre define in pinctrl dtsi > --- > .../arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 18 ++++++++++++------ > 1 file changed, 12 insertions(+), 6 deletions(-) > > diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts > index 966bbc582d89..721e87a3a464 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts > +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts > @@ -338,7 +338,7 @@ &pcie30phy { > > &pcie3x4 { > pinctrl-names = "default"; > - pinctrl-0 = <&pcie3_rst>; > + pinctrl-0 = <&pcie30x4_pins>; > reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>; > vpcie3v3-supply = <&vcc3v3_pcie30>; > status = "okay"; > @@ -377,14 +377,20 @@ pcie2_2_rst: pcie2-2-rst { > }; > }; > > - pcie3 { > - pcie3_rst: pcie3-rst { > - rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>; > - }; > - > + pcie30x4 { > pcie3_vcc3v3_en: pcie3-vcc3v3-en { > rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; > }; > + > + pcie30x4_pins: pcie30x4-pins { > + rockchip,pins = > + /* PCIE30X4_CLKREQn_M1_L */ > + <4 RK_PB4 4 &pcfg_pull_up>, Should -------------^ replace with RK_FUNC_GPIO ? since its a gpio controlled? > + /* PCIE30X4_PERSTn_M1_L */ > + <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>, > + /* PCIE30X4_WAKEn_M1_L */ > + <4 RK_PB5 4 &pcfg_pull_down>; > + }; > }; > Thanks -Anand
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts index 966bbc582d89..721e87a3a464 100644 --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts @@ -338,7 +338,7 @@ &pcie30phy { &pcie3x4 { pinctrl-names = "default"; - pinctrl-0 = <&pcie3_rst>; + pinctrl-0 = <&pcie30x4_pins>; reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>; vpcie3v3-supply = <&vcc3v3_pcie30>; status = "okay"; @@ -377,14 +377,20 @@ pcie2_2_rst: pcie2-2-rst { }; }; - pcie3 { - pcie3_rst: pcie3-rst { - rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>; - }; - + pcie30x4 { pcie3_vcc3v3_en: pcie3-vcc3v3-en { rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; }; + + pcie30x4_pins: pcie30x4-pins { + rockchip,pins = + /* PCIE30X4_CLKREQn_M1_L */ + <4 RK_PB4 4 &pcfg_pull_up>, + /* PCIE30X4_PERSTn_M1_L */ + <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>, + /* PCIE30X4_WAKEn_M1_L */ + <4 RK_PB5 4 &pcfg_pull_down>; + }; }; usb {
Add missing pinctrl settings for PCIe 3.0 x4 clock request and wake signals. Each component of PCIe communication have the following control signals: PERST, WAKE, CLKREQ, and REFCLK. These signals work to generate high-speed signals and communicate with other PCIe devices. Used by root complex to endpoint depending on the power state. PERST is referred to as a fundamental reset. PERST should be held low until all the power rails in the system and the reference clock are stable. A transition from low to high in this signal usually indicates the beginning of link initialization. WAKE signal is an active-low signal that is used to return the PCIe interface to an active state when in a low-power state. CLKREQ signal is also an active-low signal and is used to request the reference clock. Rename node from 'pcie3' to 'pcie30x4' to align with schematic nomenclature. Signed-off-by: Anand Moon <linux.amoon@gmail.com> --- V3: use pinctrl local to board V2: Update the commit messge to describe the changs. use pinctl group as its pre define in pinctrl dtsi --- .../arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)