@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2-of10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-edimm2.2.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-firefly-jd4-core-mb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-ringneck-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
new file mode 100644
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "px30-firefly-jd4-core.dtsi"
+
+/ {
+ model = "Firefly Core-PX30-JD4 on MB-JD4-PX30 baseboard";
+ compatible = "firefly,px30-jd4-core-mb", "firefly,px30-jd4-core",
+ "rockchip,px30";
+
+ aliases {
+ ethernet0 = &gmac;
+ mmc0 = &sdmmc;
+ mmc1 = &sdio;
+ mmc2 = &emmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ dc_12v: dc-12v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ adc-keys {
+ compatible = "adc-keys";
+ io-channels = <&saradc 2>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1500000>;
+ poll-interval = <100>;
+
+ button-recovery {
+ label = "Recovery";
+ linux,code = <KEY_VENDOR>;
+ press-threshold-microvolt = <18000>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blue_led>, <&green_led>;
+
+ blue-led {
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "on";
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+ label = "px30-mb-jd4:blue:work";
+ linux,default-trigger = "heartbeat";
+ };
+
+ green-led {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
+ label = "px30-mb-jd4:blue:diy";
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - PDN (power down when low)
+ */
+ reset-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>; /* GPIO3_A4 */
+ };
+
+ vcc5v0_baseboard: vcc5v0-baseboard-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+};
+
+&gmac {
+ clock_in_out = "output";
+ phy-supply = <&vcc_rmii>;
+ snps,reset-gpio = <&gpio2 13 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 50000 50000>;
+ status = "okay";
+};
+
+&pinctrl {
+ leds {
+ blue_led: blue-led {
+ rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ green_led: green-led {
+ rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins =
+ <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <800>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdio {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ keep-power-in-suspend;
+ non-removable;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+
+ u2phy_host: host-port {
+ status = "okay";
+ };
+
+ u2phy_otg: otg-port {
+ status = "okay";
+ };
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m1_xfer>;
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
The Firefly MB-PX30-JD4 is a baseboard for the Core-PX30-JD4 SoM. Signed-off-by: Christopher Obbard <chris.obbard@collabora.com> --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/px30-firefly-jd4-core-mb.dts | 179 +++++++++++++++++++++ 2 files changed, 180 insertions(+)