diff mbox series

[v2,3/3] arm64: dts: rockchip: add HDMI support to rk3588-jaguar

Message ID 20241024151403.1748554-4-heiko@sntech.de (mailing list archive)
State New
Headers show
Series HDMI Support for Theobroma/Cherry rk3588 boards | expand

Commit Message

Heiko Stübner Oct. 24, 2024, 3:14 p.m. UTC 
From: Heiko Stuebner <heiko.stuebner@cherry.de>

The jaguar has an hdmi output port, which is connected
to the hdmi0 controller of the rk3588.

Add the necessary plumbing to enable it using the recently merged
hdmi-qp controller.

Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
---
 .../arm64/boot/dts/rockchip/rk3588-jaguar.dts | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)

Comments

Quentin Schulz Oct. 24, 2024, 5:33 p.m. UTC | #1 
Hi Heiko,

On 10/24/24 5:14 PM, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
> 
> The jaguar has an hdmi output port, which is connected
> to the hdmi0 controller of the rk3588.
> 
> Add the necessary plumbing to enable it using the recently merged
> hdmi-qp controller.
> 
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>

I have this Chinese portable HDMI display[1] which doesn't print 
anything at boot but works with modetest. Same behavior can be observed 
on downstream, maybe we can get some people interested in debugging this 
now that it also impacts upstream :)

With a decent, FHD, monitor everything is fine so:

Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>

Thanks!
Quentin

[1] https://www.amazon.de/dp/B0CKYR6FN5
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts b/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
index e24da1a4331d..6a59887979ce 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
@@ -8,6 +8,7 @@ 
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
 #include <dt-bindings/usb/pd.h>
 #include "rk3588.dtsi"
 
@@ -58,6 +59,17 @@  emmc_pwrseq: emmc-pwrseq {
 		reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
 	};
 
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi0_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -271,6 +283,29 @@  &gpu {
 	status = "okay";
 };
 
+&hdmi0 {
+	/* No CEC on Jaguar */
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmim0_tx0_hpd &hdmim0_tx0_scl &hdmim0_tx0_sda>;
+	status = "okay";
+};
+
+&hdmi0_in {
+	hdmi0_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi0>;
+	};
+};
+
+&hdmi0_out {
+	hdmi0_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdptxphy_hdmi0 {
+	status = "okay";
+};
+
 &i2c0 {
 	pinctrl-0 = <&i2c0m2_xfer>;
 	status = "okay";
@@ -1052,3 +1087,18 @@  &usb_host1_ehci {
 &usb_host1_ohci {
 	status = "okay";
 };
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi0_in_vp0>;
+	};
+};