@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
new file mode 100644
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+// Copyright (c) 2017-2019 Arm Ltd.
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+ model = "Beelink A1";
+ compatible = "azw,beelink-a1", "rockchip,rk3328";
+
+ /*
+ * UART pins, as viewed with bottom of case removed:
+ *
+ * Front
+ * /-------
+ * L / o <- Gnd
+ * e / o <-- Rx
+ * f / o <--- Tx
+ * t / o <---- +3.3v
+ * |
+ */
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac_clkin: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_clkin";
+ #clock-cells = <0>;
+ };
+
+ vcc_host_5v: usb3-current-switch {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb30_host_drv>;
+ regulator-name = "vcc_host_5v";
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_sys: vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&analog_sound {
+ simple-audio-card,name = "Analog A/V";
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ no-sd;
+ no-sdio;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ vmmc-supply = <&vcc_io>;
+ vqmmc-supply = <&vcc18_emmc>;
+ status = "okay";
+};
+
+&gmac2io {
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+ assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+ clock_in_out = "input";
+ phy-handle = <&rtl8211f>;
+ phy-mode = "rgmii";
+ phy-supply = <&vcc_io>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmiim1_pins>;
+ snps,aal;
+ snps,pbl = <0x4>;
+ tx_delay = <0x26>;
+ rx_delay = <0x11>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtl8211f: phy@0 {
+ reg = <0>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gpu {
+ mali-supply = <&vdd_logic>;
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmiphy {
+ status = "okay";
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <1000000>;
+ i2c-scl-falling-time-ns = <5>;
+ i2c-scl-rising-time-ns = <83>;
+ status = "okay";
+
+ pmic@18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_io>;
+ vcc6-supply = <&vcc_io>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd_18: LDO_REG1 {
+ regulator-name = "vdd_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc_18emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_11: LDO_REG3 {
+ regulator-name = "vdd_11";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1100000>;
+ };
+ };
+ };
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&i2s1 {
+ status = "okay";
+};
+
+&io_domains {
+ vccio1-supply = <&vcc_io>;
+ vccio2-supply = <&vcc18_emmc>;
+ vccio3-supply = <&vcc_io>;
+ vccio4-supply = <&vdd_18>;
+ vccio5-supply = <&vcc_io>;
+ vccio6-supply = <&vdd_18>;
+ pmuio-supply = <&vcc_io>;
+ status = "okay";
+};
+
+&pinctrl {
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb3 {
+ usb30_host_drv: usb30-host-drv {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ bt_dis: bt-dis {
+ rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+
+ bt_wake_host: bt-wake-host {
+ rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ chip_en: chip-en {
+ rockchip,pins = <2 RK_PC3 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+
+ host_wake_bt: host-wake-bt {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+
+ wl_dis: wl-dis {
+ rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+
+ wl_wake_host: wl-wake-host {
+ rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+ vmmc-supply = <&vcc_io>;
+ vqmmc-supply = <&vcc_io>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&usb20_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_dis &bt_wake_host &chip_en &host_wake_bt &wl_dis &wl_wake_host>;
+ status = "okay";
+};
+
+&vop {
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
Beelink A1 is a TV box implementing the higher-end options of the RK3328 reference design - the DTB from the stock Android firmware is clearly the "rk3328-box-plus" variant from the Rockchip 3.10 BSP with minor modifications to accommodate the USB WiFi module and additional VFD-style LED driver. It features: - 4GB of 32-bit LPDDR3 - 16GB of HS200 eMMC (newer models with 32GB also exist) - Realtek RTL8211F phy for gigabit ethernet - Fn-Link 6221E-UUC module (RealTek RTL8821CU) for 11ac WiFi and Bluetooth 4.2 - HDMI and analog A/V - 1x USB 3.0 type A host, 1x USB 2.0 type A OTG, 1x micro SD - IR receiver and a neat little LED clock display. Signed-off-by: Robin Murphy <robin.murphy@arm.com> --- arch/arm64/boot/dts/rockchip/Makefile | 1 + arch/arm64/boot/dts/rockchip/rk3328-a1.dts | 359 +++++++++++++++++++++ 2 files changed, 360 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-a1.dts