| Message ID | 1382033211-32329-2-git-send-email-s.nawrocki@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 10/17/2013 08:06 PM, Sylwester Nawrocki wrote: > This patch adds binding documentation for the Samsung S5K6A3(YX) > raw image sensor. > > Signed-off-by: Sylwester Nawrocki<s.nawrocki@samsung.com> > Signed-off-by: Kyungmin Park<kyungmin.park@samsung.com> Hi Mauro, Can we merge it now without a DT binding maintainer Ack ? There was no comments for 2 months and I believe the Ack is not mandatory for this kind of standard binding and very similar binding has been already reviewed (for the S5K5BAF sensor). I just updated slightly the clock/clock-names property description, so I would post patch [1] to the mailing lists before adding it to a pull request. Thanks, Sylwester [1] http://git.linuxtv.org/snawrocki/samsung.git/commitdiff/4249788ea8c9b9d9bc95cd088351e2cdda1838f6 > --- > Changes since v2: > - added AF regulator supply. > --- > .../devicetree/bindings/media/samsung-s5k6a3.txt | 32 ++++++++++++++++++++ > 1 file changed, 32 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt > > diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt > new file mode 100644 > index 0000000..3806e77 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt > @@ -0,0 +1,32 @@ > +Samsung S5K6A3(YX) raw image sensor > +--------------------------------- > + > +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces > +and CCI (I2C compatible) control bus. > + > +Required properties: > + > +- compatible : "samsung,s5k6a3"; > +- reg : I2C slave address of the sensor; > +- svdda-supply : core voltage supply; > +- svddio-supply : I/O voltage supply; > +- afvdd-supply : AF (actuator) voltage supply; > +- gpios : specifier of a GPIO connected to the RESET pin; > +- clocks : should contain the sensor's EXTCLK clock specifier, > + from common clock bindings; > +- clock-names : should contain "extclk" entry; > + > +Optional properties: > + > +- clock-frequency : the frequency at which the "extclk" clock should be > + configured to operate, in Hz; if this property is not > + specified default 24 MHz value will be used. > + > +The common video interfaces bindings (see video-interfaces.txt) should be > +used to specify link to the image data receiver. The S5K6A3(YX) device > +node should contain one 'port' child node with an 'endpoint' subnode. > + > +Following properties are valid for the endpoint node: > + > +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in > + video-interfaces.txt. The sensor supports only one data lane. -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt new file mode 100644 index 0000000..3806e77 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt @@ -0,0 +1,32 @@ +Samsung S5K6A3(YX) raw image sensor +--------------------------------- + +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces +and CCI (I2C compatible) control bus. + +Required properties: + +- compatible : "samsung,s5k6a3"; +- reg : I2C slave address of the sensor; +- svdda-supply : core voltage supply; +- svddio-supply : I/O voltage supply; +- afvdd-supply : AF (actuator) voltage supply; +- gpios : specifier of a GPIO connected to the RESET pin; +- clocks : should contain the sensor's EXTCLK clock specifier, + from common clock bindings; +- clock-names : should contain "extclk" entry; + +Optional properties: + +- clock-frequency : the frequency at which the "extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be +used to specify link to the image data receiver. The S5K6A3(YX) device +node should contain one 'port' child node with an 'endpoint' subnode. + +Following properties are valid for the endpoint node: + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. The sensor supports only one data lane.