@@ -21,6 +21,10 @@ Optional properties:
number should be provided. If it is externally controlled and no GPIO
entry then driver will just configure this rails as external control
and will not provide any enable/disable APIs.
+- ti,overcurrent-wait: This is applicable to FET registers, which have a
+ poorly defined "overcurrent wait" field. If this property is present it
+ should be between 0 - 3. If this property isn't present we won't touch the
+ "overcurrent wait" field and we'll leave it to the BIOS/EC to deal with.
Each regulator is defined using the standard binding for regulators.
@@ -28,15 +28,57 @@
#include <linux/regulator/of_regulator.h>
#include <linux/mfd/tps65090.h>
+#define CTRL_WT_BIT 2 /* Regulator wait time 0 bit */
+
+#define MAX_OVERCURRENT_WAIT 3 /* Overcurrent wait must be <= this */
+
+/**
+ * struct tps65090_regulator - Per-regulator data for a tps65090 regulator
+ *
+ * @dev: Pointer to our device.
+ * @desc: The struct regulator_desc for the regulator.
+ * @rdev: The struct regulator_dev for the regulator.
+ * @overcurrent_wait_valid: True if overcurrent_wait is valid.
+ * @overcurrent_wait: For FETs, the value to put in the WTFET bitfield.
+ */
+
struct tps65090_regulator {
struct device *dev;
struct regulator_desc *desc;
struct regulator_dev *rdev;
+ bool overcurrent_wait_valid;
+ int overcurrent_wait;
};
static struct regulator_ops tps65090_ext_control_ops = {
};
+/**
+ * tps65090_reg_set_overcurrent_wait - Setup overcurrent wait
+ *
+ * This will set the overcurrent wait time based on what's in the regulator
+ * info.
+ *
+ * @ri: Overall regulator data
+ * @rdev: Regulator device
+ * @return 0 if no error, non-zero if there was an error writing the register.
+ */
+static int tps65090_reg_set_overcurrent_wait(struct tps65090_regulator *ri,
+ struct regulator_dev *rdev)
+{
+ int ret;
+
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ MAX_OVERCURRENT_WAIT << CTRL_WT_BIT,
+ ri->overcurrent_wait << CTRL_WT_BIT);
+ if (ret) {
+ dev_err(&rdev->dev, "Error updating overcurrent wait %#x\n",
+ rdev->desc->enable_reg);
+ }
+
+ return ret;
+}
+
static struct regulator_ops tps65090_reg_contol_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
@@ -209,6 +251,11 @@ static struct tps65090_platform_data *tps65090_parse_dt_reg_data(
rpdata->gpio = of_get_named_gpio(np,
"dcdc-ext-control-gpios", 0);
+ if (of_property_read_u32(tps65090_matches[idx].of_node,
+ "ti,overcurrent-wait",
+ &rpdata->overcurrent_wait) == 0)
+ rpdata->overcurrent_wait_valid = true;
+
tps65090_pdata->reg_pdata[idx] = rpdata;
}
return tps65090_pdata;
@@ -258,6 +305,8 @@ static int tps65090_regulator_probe(struct platform_device *pdev)
ri = &pmic[num];
ri->dev = &pdev->dev;
ri->desc = &tps65090_regulator_desc[num];
+ ri->overcurrent_wait_valid = tps_pdata->overcurrent_wait_valid;
+ ri->overcurrent_wait = tps_pdata->overcurrent_wait;
/*
* TPS5090 DCDC support the control from external digital input.
@@ -299,6 +348,12 @@ static int tps65090_regulator_probe(struct platform_device *pdev)
}
ri->rdev = rdev;
+ if (ri->overcurrent_wait_valid) {
+ ret = tps65090_reg_set_overcurrent_wait(ri, rdev);
+ if (ret < 0)
+ return ret;
+ }
+
/* Enable external control if it is require */
if (tps_pdata && is_dcdc(num) && tps_pdata->reg_init_data &&
tps_pdata->enable_ext_control) {
@@ -92,11 +92,16 @@ struct tps65090 {
* DCDC1, DCDC2 and DCDC3.
* @gpio: Gpio number if external control is enabled and controlled through
* gpio.
+ * @overcurrent_wait_valid: True if the overcurrent_wait should be applied.
+ * @overcurrent_wait: Value to set as the overcurrent wait time. This is the
+ * actual bitfield value, not a time in ms (valid value are 0 - 3).
*/
struct tps65090_regulator_plat_data {
struct regulator_init_data *reg_init_data;
bool enable_ext_control;
int gpio;
+ bool overcurrent_wait_valid;
+ int overcurrent_wait;
};
struct tps65090_platform_data {