| Message ID | 1405680964-6869-2-git-send-email-inki.dae@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Inki, +CC: Thierry and Alexandre On 07/18/2014 12:56 PM, Inki Dae wrote: > This patch adds below two flags for LPM transfer, and it attaches LPM flags > to a msg in accordance with master's mode_flags set by LCD Panel driver. > > MIPI_DSI_MODE_CMD_LPM: low power command transfer > MIPI_DSI_MODE_VIDEO_LPM: low power video transfer What is the difference between these two? Why not just MIPI_DSI_MODE_LPM combined optionally with MIPI_DSI_MODE_VIDEO ? Anyway as I understand the only role of this flag is to always trigger MIPI_DSI_MSG_USE_LPM flag in DSI message. Maybe better is to check both flags in DSI host, using some helper function. > > MIPI DSI spec says, > "the host processor controls the desired mode of clock operation. > Host protocol and applications control Clock Lane operating mode > (High Speed or Low Power mode). System designers are responsible > for understanding the clock requirements for peripherals attached > to DSI and controlling clock behavior in accordance with those > requirements." > > Some LCD Panel devices, nt35502a, would need LPM transfer support > because they should receive some initial commands with LPM by default > hardware setting. It would be good to see usage of this flag in the driver. Is it possible to post it? I have posted few months ago TC358764 driver[1] which also uses LPM for initialization, have you look at it. [1]: http://lists.freedesktop.org/archives/dri-devel/2014-February/053713.html Regards Andrzej > > Signed-off-by: Inki Dae <inki.dae@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> > --- > drivers/gpu/drm/drm_mipi_dsi.c | 3 +++ > include/drm/drm_mipi_dsi.h | 4 ++++ > 2 files changed, 7 insertions(+) > > diff --git a/drivers/gpu/drm/drm_mipi_dsi.c b/drivers/gpu/drm/drm_mipi_dsi.c > index e633df2..6b2bbda 100644 > --- a/drivers/gpu/drm/drm_mipi_dsi.c > +++ b/drivers/gpu/drm/drm_mipi_dsi.c > @@ -232,6 +232,9 @@ int mipi_dsi_dcs_write(struct mipi_dsi_device *dsi, unsigned int channel, > break; > } > > + if (dsi->mode_flags & MIPI_DSI_MODE_CMD_LPM) > + msg.flags = MIPI_DSI_MSG_USE_LPM; > + > return ops->transfer(dsi->host, &msg); > } > EXPORT_SYMBOL(mipi_dsi_dcs_write); > diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h > index 944f33f..1c41e49 100644 > --- a/include/drm/drm_mipi_dsi.h > +++ b/include/drm/drm_mipi_dsi.h > @@ -94,6 +94,10 @@ void mipi_dsi_host_unregister(struct mipi_dsi_host *host); > #define MIPI_DSI_MODE_VSYNC_FLUSH BIT(8) > /* disable EoT packets in HS mode */ > #define MIPI_DSI_MODE_EOT_PACKET BIT(9) > +/* command low power mode */ > +#define MIPI_DSI_MODE_CMD_LPM BIT(10) > +/* video low power mode */ > +#define MIPI_DSI_MODE_VIDEO_LPM BIT(11) > > enum mipi_dsi_pixel_format { > MIPI_DSI_FMT_RGB888, -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 2014? 07? 24? 19:23, Andrzej Hajda wrote: > Hi Inki, > > +CC: Thierry and Alexandre > > On 07/18/2014 12:56 PM, Inki Dae wrote: >> This patch adds below two flags for LPM transfer, and it attaches LPM flags >> to a msg in accordance with master's mode_flags set by LCD Panel driver. >> >> MIPI_DSI_MODE_CMD_LPM: low power command transfer >> MIPI_DSI_MODE_VIDEO_LPM: low power video transfer > What is the difference between these two? They mean that MIPI DSI controller have to transfer command or video to Panel in Low Power Mode according to these flags. > Why not just MIPI_DSI_MODE_LPM combined optionally with > MIPI_DSI_MODE_VIDEO ? > Anyway as I understand the only role of this flag is to always trigger > MIPI_DSI_MSG_USE_LPM flag in DSI message. Maybe better is to check both > flags in DSI host, using some helper function. No any flag would mean that video and command data have to be transferred in HS mode. On the other hands, if there is one of above flags, the data would be transferred in Low Power Mode. So I think separated flags, MIPI_DSI_MODE_VIDEO/COMMAND and MIPI_DSI_MODE_LPM causes unnecessary flag combination. > >> >> MIPI DSI spec says, >> "the host processor controls the desired mode of clock operation. >> Host protocol and applications control Clock Lane operating mode >> (High Speed or Low Power mode). System designers are responsible >> for understanding the clock requirements for peripherals attached >> to DSI and controlling clock behavior in accordance with those >> requirements." >> >> Some LCD Panel devices, nt35502a, would need LPM transfer support >> because they should receive some initial commands with LPM by default >> hardware setting. > > It would be good to see usage of this flag in the driver. Is it possible > to post it? Yes, but that driver is needed for more cleanup works. Anyway I will post it in the near future. > > I have posted few months ago TC358764 driver[1] which also uses LPM for > initialization, have you look at it. > > [1]: > http://lists.freedesktop.org/archives/dri-devel/2014-February/053713.html > > Regards > Andrzej > >> >> Signed-off-by: Inki Dae <inki.dae@samsung.com> >> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> >> --- >> drivers/gpu/drm/drm_mipi_dsi.c | 3 +++ >> include/drm/drm_mipi_dsi.h | 4 ++++ >> 2 files changed, 7 insertions(+) >> >> diff --git a/drivers/gpu/drm/drm_mipi_dsi.c b/drivers/gpu/drm/drm_mipi_dsi.c >> index e633df2..6b2bbda 100644 >> --- a/drivers/gpu/drm/drm_mipi_dsi.c >> +++ b/drivers/gpu/drm/drm_mipi_dsi.c >> @@ -232,6 +232,9 @@ int mipi_dsi_dcs_write(struct mipi_dsi_device *dsi, unsigned int channel, >> break; >> } >> >> + if (dsi->mode_flags & MIPI_DSI_MODE_CMD_LPM) >> + msg.flags = MIPI_DSI_MSG_USE_LPM; >> + >> return ops->transfer(dsi->host, &msg); >> } >> EXPORT_SYMBOL(mipi_dsi_dcs_write); >> diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h >> index 944f33f..1c41e49 100644 >> --- a/include/drm/drm_mipi_dsi.h >> +++ b/include/drm/drm_mipi_dsi.h >> @@ -94,6 +94,10 @@ void mipi_dsi_host_unregister(struct mipi_dsi_host *host); >> #define MIPI_DSI_MODE_VSYNC_FLUSH BIT(8) >> /* disable EoT packets in HS mode */ >> #define MIPI_DSI_MODE_EOT_PACKET BIT(9) >> +/* command low power mode */ >> +#define MIPI_DSI_MODE_CMD_LPM BIT(10) >> +/* video low power mode */ >> +#define MIPI_DSI_MODE_VIDEO_LPM BIT(11) >> >> enum mipi_dsi_pixel_format { >> MIPI_DSI_FMT_RGB888, > > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/gpu/drm/drm_mipi_dsi.c b/drivers/gpu/drm/drm_mipi_dsi.c index e633df2..6b2bbda 100644 --- a/drivers/gpu/drm/drm_mipi_dsi.c +++ b/drivers/gpu/drm/drm_mipi_dsi.c @@ -232,6 +232,9 @@ int mipi_dsi_dcs_write(struct mipi_dsi_device *dsi, unsigned int channel, break; } + if (dsi->mode_flags & MIPI_DSI_MODE_CMD_LPM) + msg.flags = MIPI_DSI_MSG_USE_LPM; + return ops->transfer(dsi->host, &msg); } EXPORT_SYMBOL(mipi_dsi_dcs_write); diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h index 944f33f..1c41e49 100644 --- a/include/drm/drm_mipi_dsi.h +++ b/include/drm/drm_mipi_dsi.h @@ -94,6 +94,10 @@ void mipi_dsi_host_unregister(struct mipi_dsi_host *host); #define MIPI_DSI_MODE_VSYNC_FLUSH BIT(8) /* disable EoT packets in HS mode */ #define MIPI_DSI_MODE_EOT_PACKET BIT(9) +/* command low power mode */ +#define MIPI_DSI_MODE_CMD_LPM BIT(10) +/* video low power mode */ +#define MIPI_DSI_MODE_VIDEO_LPM BIT(11) enum mipi_dsi_pixel_format { MIPI_DSI_FMT_RGB888,
This patch adds below two flags for LPM transfer, and it attaches LPM flags to a msg in accordance with master's mode_flags set by LCD Panel driver. MIPI_DSI_MODE_CMD_LPM: low power command transfer MIPI_DSI_MODE_VIDEO_LPM: low power video transfer MIPI DSI spec says, "the host processor controls the desired mode of clock operation. Host protocol and applications control Clock Lane operating mode (High Speed or Low Power mode). System designers are responsible for understanding the clock requirements for peripherals attached to DSI and controlling clock behavior in accordance with those requirements." Some LCD Panel devices, nt35502a, would need LPM transfer support because they should receive some initial commands with LPM by default hardware setting. Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> --- drivers/gpu/drm/drm_mipi_dsi.c | 3 +++ include/drm/drm_mipi_dsi.h | 4 ++++ 2 files changed, 7 insertions(+)