@@ -625,6 +625,7 @@ choice
config DEBUG_S3C_UART0
depends on PLAT_SAMSUNG
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
+ select DEBUG_S3C24XX_UART if ARCH_S3C24XX
bool "Use S3C UART 0 for low-level debug"
help
Say Y here if you want the debug print routines to direct
@@ -637,6 +638,7 @@ choice
config DEBUG_S3C_UART1
depends on PLAT_SAMSUNG
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
+ select DEBUG_S3C24XX_UART if ARCH_S3C24XX
bool "Use S3C UART 1 for low-level debug"
help
Say Y here if you want the debug print routines to direct
@@ -649,6 +651,7 @@ choice
config DEBUG_S3C_UART2
depends on PLAT_SAMSUNG
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
+ select DEBUG_S3C24XX_UART if ARCH_S3C24XX
bool "Use S3C UART 2 for low-level debug"
help
Say Y here if you want the debug print routines to direct
@@ -950,6 +953,10 @@ config DEBUG_EXYNOS_UART
config DEBUG_S3C2410_UART
bool
+ select DEBUG_S3C24XX_UART
+
+config DEBUG_S3C24XX_UART
+ bool
config DEBUG_OMAP2PLUS_UART
bool
@@ -1059,6 +1066,12 @@ config DEBUG_UART_PHYS
default 0x40090000 if ARCH_LPC32XX
default 0x40100000 if DEBUG_PXA_UART1
default 0x42000000 if ARCH_GEMINI
+ default 0x50000000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART0 || \
+ DEBUG_S3C2410_UART0)
+ default 0x50004000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART1 || \
+ DEBUG_S3C2410_UART1)
+ default 0x50008000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART2 || \
+ DEBUG_S3C2410_UART2)
default 0x7c0003f8 if FOOTBRIDGE
default 0x80230000 if DEBUG_PICOXCELL_UART
default 0x80070000 if DEBUG_IMX23_UART
@@ -1088,7 +1101,7 @@ config DEBUG_UART_PHYS
default 0xfffff700 if ARCH_IOP33X
depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
DEBUG_LL_UART_EFM32 || \
- DEBUG_UART_8250 || DEBUG_UART_PL01X
+ DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_S3C24XX_UART
config DEBUG_UART_VIRT
hex "Virtual base address of debug UART"
@@ -1105,6 +1118,12 @@ config DEBUG_UART_VIRT
default 0xf2100000 if DEBUG_PXA_UART1
default 0xf4090000 if ARCH_LPC32XX
default 0xf4200000 if ARCH_GEMINI
+ default 0xf7000000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART0 || \
+ DEBUG_S3C2410_UART0)
+ default 0xf7004000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART1 || \
+ DEBUG_S3C2410_UART1)
+ default 0xf7008000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART2 || \
+ DEBUG_S3C2410_UART2)
default 0xf7fc9000 if DEBUG_BERLIN_UART
default 0xf8009000 if DEBUG_VEXPRESS_UART0_CA9
default 0xf8090000 if DEBUG_VEXPRESS_UART0_RS1
@@ -1146,7 +1165,7 @@ config DEBUG_UART_VIRT
default 0xff003000 if DEBUG_U300_UART
default DEBUG_UART_PHYS if !MMU
depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
- DEBUG_UART_8250 || DEBUG_UART_PL01X
+ DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_S3C24XX_UART
config DEBUG_UART_8250_SHIFT
int "Register offset shift for the 8250 debug UART"
@@ -12,18 +12,13 @@
* published by the Free Software Foundation.
*/
-#include <mach/map.h>
#include <linux/serial_s3c.h>
#define S3C2410_UART1_OFF (0x4000)
.macro addruart, rp, rv, tmp
- ldr \rp, = S3C24XX_PA_UART
- ldr \rv, = S3C24XX_VA_UART
-#if CONFIG_DEBUG_S3C_UART != 0
- add \rp, \rp, #(S3C2410_UART1_OFF * CONFIG_DEBUG_S3C_UART)
- add \rv, \rv, #(S3C2410_UART1_OFF * CONFIG_DEBUG_S3C_UART)
-#endif
+ ldr \rp, = CONFIG_DEBUG_UART_PHYS
+ ldr \rv, = CONFIG_DEBUG_UART_VIRT
.endm
.macro fifo_full_s3c2410 rd, rx
This removes the need for mach/-headers in the debug macro. Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- arch/arm/Kconfig.debug | 23 +++++++++++++++++++++-- arch/arm/mach-s3c24xx/include/mach/debug-macro.S | 9 ++------- 2 files changed, 23 insertions(+), 9 deletions(-)