| Message ID | 1409066937-3574-2-git-send-email-javier.martinez@collabora.co.uk (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
Hi Javier, Am 26.08.2014 17:28, schrieb Javier Martinez Canillas: > From: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > > The Peach Pit board has an Atmel maXTouch trackpad device. > Add the needed Device Tree nodes to support it. > > This Device Tree change is based on the Chrome OS 3.8 tree > but adapted to use the mainline Atmel maXTouch DT binding. > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > [javier.martinez: added linux,gpio-keymap property and changed IRQ type] > Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> > --- > > Changes since v1: > - Change trackpad IRQ pad function from 0x0 (GPIO input) to 0xf (GPIO IRQ). > suggested by Tomasz Figa. > - Remove BTN_TOOL_* from "linux,gpio-keymap" property since those are set > by input mt core if INPUT_MT_POINTER is set. Suggested by Nick Dyer. > - Use correct values for "linux,gpio-keymap" property. Suggested by Nick Dyer. > - Remove support for Peach Pi board since it uses a different Atmel touchpad > that requires an Atmel object protocol (T100) not supported by the driver. > - Use IRQ type constants from <dt-bindings/interrupt-controller/irq.h> instead > of magic numbers. Suggested by Andreas Farber. > --- > arch/arm/boot/dts/exynos5420-peach-pit.dts | 31 ++++++++++++++++++++++++++++++ > 1 file changed, 31 insertions(+) > > diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts > index 228a6b1..e4f82d5 100644 > --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts > +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts > @@ -11,6 +11,7 @@ > /dts-v1/; > #include <dt-bindings/input/input.h> > #include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/irq.h> > #include "exynos5420.dtsi" > > / { > @@ -157,6 +158,29 @@ > }; > }; > > +&hsi2c_8 { > + status = "okay"; > + clock-frequency = <333000>; > + > + trackpad@4b { > + compatible="atmel,maxtouch"; > + reg=<0x4b>; > + interrupt-parent=<&gpx1>; > + interrupts=<1 IRQ_TYPE_EDGE_FALLING>; Nit: Here's a style break (4x spaces around '=' missing). > + wakeup-source; > + pinctrl-names = "default"; > + pinctrl-0 = <&trackpad_irq>; > + linux,gpio-keymap = < KEY_RESERVED > + KEY_RESERVED > + 0 /* GPIO 0 */ > + 0 /* GPIO 1 */ > + 0 /* GPIO 2 */ > + BTN_LEFT /* GPIO 3 */ > + KEY_RESERVED > + KEY_RESERVED >; > + }; Coincidentally, I experimentally came up with a very similar DT node for Spring the weekend: + trackpad@4b { + compatible = "atmel,maxtouch"; + reg = <0x4b>; + interrupt-parent = <&gpx1>; + interrupts = <2 IRQ_TYPE_NONE>; + pinctrl-names = "default"; + pinctrl-0 = <&trackpad_irq>; + linux,gpio-keymap = <KEY_RESERVED + KEY_RESERVED + KEY_RESERVED + KEY_RESERVED + KEY_RESERVED + BTN_LEFT>; + wakeup-source; + }; 0 == KEY_RESERVED, so you can consistently use it for GPIO 0-2, too. :) I probably should add the two trailing _RESERVEDs, too? With my above snippet I got an awful lot of "Interrupt triggered but zero messages" warnings (which I simply commented out as quickfix). Is that why you are using _EDGE_FALLING? Or pin-function 0xf? (In my case the ChromeOS DT had IRQ_TYPE_NONE and pin-function 0x0.) Regards, Andreas > +}; > + > &hsi2c_9 { > status = "okay"; > clock-frequency = <400000>; > @@ -249,6 +273,13 @@ > samsung,pin-drv = <0>; > }; > > + trackpad_irq: trackpad-irq { > + samsung,pins = "gpx1-1"; > + samsung,pin-function = <0xf>; > + samsung,pin-pud = <0>; > + samsung,pin-drv = <0>; > + }; > + > power_key_irq: power-key-irq { > samsung,pins = "gpx1-2"; > samsung,pin-function = <0>;
Hello Andreas, On 08/27/2014 12:53 AM, Andreas Färber wrote: >> >> +&hsi2c_8 { >> + status = "okay"; >> + clock-frequency = <333000>; >> + >> + trackpad@4b { >> + compatible="atmel,maxtouch"; >> + reg=<0x4b>; >> + interrupt-parent=<&gpx1>; >> + interrupts=<1 IRQ_TYPE_EDGE_FALLING>; > > Nit: Here's a style break (4x spaces around '=' missing). > True, these bits were copied from the downstream Chrome OS verbatim and the missing space around '=' was there, I missed that when reviewing. I'll re-spin and fix those style issues. >> + wakeup-source; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&trackpad_irq>; >> + linux,gpio-keymap = < KEY_RESERVED >> + KEY_RESERVED >> + 0 /* GPIO 0 */ >> + 0 /* GPIO 1 */ >> + 0 /* GPIO 2 */ >> + BTN_LEFT /* GPIO 3 */ >> + KEY_RESERVED >> + KEY_RESERVED >; >> + }; > > Coincidentally, I experimentally came up with a very similar DT node for > Spring the weekend: > > + trackpad@4b { > + compatible = "atmel,maxtouch"; > + reg = <0x4b>; > + interrupt-parent = <&gpx1>; > + interrupts = <2 IRQ_TYPE_NONE>; > + pinctrl-names = "default"; > + pinctrl-0 = <&trackpad_irq>; > + linux,gpio-keymap = <KEY_RESERVED > + KEY_RESERVED > + KEY_RESERVED > + KEY_RESERVED > + KEY_RESERVED > + BTN_LEFT>; > + wakeup-source; > + }; > > 0 == KEY_RESERVED, so you can consistently use it for GPIO 0-2, too. :) > I know that the value of KEY_RESERVED is 0 but I didn't use KEY_RESERVED for the GPIO on purpose. What I understood is that the SPT_GPIOPWN_T19 object sends messages using a status byte so you have a maximum of 8 GPIO but not every maXTouch devices use all of them. So in the particular case of the device in the Peach Pit, from the 8 possible GPIO only 4 can be used and these are pins 2-5. So in theory you could connect 3 more GPIO in case you had more buttons (e.g: BTN_RIGHT, BTN_MIDDLE) but only 1 is used since the Chromebook just have BTN_LEFT. Nick sent a patch [0] that extend the atmel touchpad DT binding and the doc says "Use KEY_RESERVED for unused padding values". But is not clear what value you should use for GPIO that are actually supported by the device but have no keycode associated. So by using 0 instead of KEY_RESERVED I wanted to document that pins 2-4 are actually supported and not reserved by the device but there is no keycode associated with that GPIO. If there was a BTN_NONE or KEY_UNUSED it would had been better but I think that making a distinction between these two cases (reserved pin vs GPIO available but not used) is useful. > I probably should add the two trailing _RESERVEDs, too? > I see that is used for properties that are arrays, for example "linux,keymap" in Documentation/devicetree/bindings/input/matrix-keymap.txt. > With my above snippet I got an awful lot of "Interrupt triggered but > zero messages" warnings (which I simply commented out as quickfix). > Is that why you are using _EDGE_FALLING? Or pin-function 0xf? > (In my case the ChromeOS DT had IRQ_TYPE_NONE and pin-function 0x0.) > These are two separate but related things: a) IRQF_TRIGGER_FALLING: Yes, the Chrome OS DT for Peach Pit also has IRQ_TYPE_NONE but the DTS is not correct. If you look at the Chrome OS atmel driver (drivers/input/touchscreen/atmel_mxt_ts.c), it passes IRQF_TRIGGER_FALLING to request_threaded_irq(): /* Default to falling edge if no platform data provided */ irqflags = data->pdata ? data->pdata->irqflags : IRQF_TRIGGER_FALLING; error = request_threaded_irq(client->irq, NULL, mxt_interrupt, irqflags | IRQF_ONESHOT, client->name, data); The above code is wrong since is overwriting the edge/level type flags set by OF when parsing the "interrupts" property so you have to use the expected IRQ flags in your DTS. b) pin-function 0xf instead of 0x0: The pin-function 0x0 is GPIO input while 0xf is GPIO IRQ. Usually on other SoCs to use a GPIO IRQ you just configure the pad as GPIO input and then enable the pin as an interrupt but on Exynos SoC these are really two different functions. So if you configure the pin as GPIO input and this happens after the pin is configured as GPIO IRQ, interrupts are not triggered. I faced that issue before [1] and was solved with Tomasz's commit: f6a8249 pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs which changes the pinctrl-exynos driver to setup a pin as GPIO IRQ on .irq_request_resources instead of .irq_set_type. So, with that patch even when pin-function re-configures the function to GPIO input, is then configured as GPIO IRQ when request_threaded_irq() is called. So probably is working for you just because you tested on linux-next that already has Tomasz's changes but still the correct thing to do is to setup the pin as 0xf. This change probably is needed on other pins used as GPIO IRQ that are using 0x0 now. Sorry, the email became longer than I wanted but I hope is helpful to you. > Regards, > Andreas > Best regards, Javier [0]: https://lkml.org/lkml/2014/8/15/244 [1]: https://lkml.org/lkml/2014/8/8/621 -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Javier, Am 27.08.2014 09:13, schrieb Javier Martinez Canillas: > On 08/27/2014 12:53 AM, Andreas Färber wrote: >>> >>> +&hsi2c_8 { >>> + status = "okay"; >>> + clock-frequency = <333000>; >>> + >>> + trackpad@4b { >>> + compatible="atmel,maxtouch"; >>> + reg=<0x4b>; >>> + interrupt-parent=<&gpx1>; >>> + interrupts=<1 IRQ_TYPE_EDGE_FALLING>; >> >> Nit: Here's a style break (4x spaces around '=' missing). >> > > True, these bits were copied from the downstream Chrome OS verbatim and > the missing space around '=' was there, I missed that when reviewing. > > I'll re-spin and fix those style issues. > >>> + wakeup-source; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&trackpad_irq>; >>> + linux,gpio-keymap = < KEY_RESERVED >>> + KEY_RESERVED >>> + 0 /* GPIO 0 */ >>> + 0 /* GPIO 1 */ >>> + 0 /* GPIO 2 */ >>> + BTN_LEFT /* GPIO 3 */ >>> + KEY_RESERVED >>> + KEY_RESERVED >; >>> + }; >> >> Coincidentally, I experimentally came up with a very similar DT node for >> Spring the weekend: >> >> + trackpad@4b { >> + compatible = "atmel,maxtouch"; >> + reg = <0x4b>; >> + interrupt-parent = <&gpx1>; >> + interrupts = <2 IRQ_TYPE_NONE>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&trackpad_irq>; >> + linux,gpio-keymap = <KEY_RESERVED >> + KEY_RESERVED >> + KEY_RESERVED >> + KEY_RESERVED >> + KEY_RESERVED >> + BTN_LEFT>; >> + wakeup-source; >> + }; >> >> 0 == KEY_RESERVED, so you can consistently use it for GPIO 0-2, too. :) >> > > I know that the value of KEY_RESERVED is 0 but I didn't use KEY_RESERVED > for the GPIO on purpose. > > What I understood is that the SPT_GPIOPWN_T19 object sends messages using > a status byte so you have a maximum of 8 GPIO but not every maXTouch > devices use all of them. So in the particular case of the device in the > Peach Pit, from the 8 possible GPIO only 4 can be used and these are pins > 2-5. So in theory you could connect 3 more GPIO in case you had more > buttons (e.g: BTN_RIGHT, BTN_MIDDLE) but only 1 is used since the > Chromebook just have BTN_LEFT. FWIW when I press to the bottom right of my touchpad, I do get right-click functionality even with just BTN_LEFT specified in the keymap. Magic. :) > Nick sent a patch [0] that extend the atmel touchpad DT binding and the > doc says "Use KEY_RESERVED for unused padding values". But is not clear > what value you should use for GPIO that are actually supported by the > device but have no keycode associated. > > So by using 0 instead of KEY_RESERVED I wanted to document that pins 2-4 > are actually supported and not reserved by the device but there is no > keycode associated with that GPIO. You already documented that via comments though. > If there was a BTN_NONE or KEY_UNUSED it would had been better but I think > that making a distinction between these two cases (reserved pin vs GPIO > available but not used) is useful. Maybe Nick can comment here. >> I probably should add the two trailing _RESERVEDs, too? >> > > I see that is used for properties that are arrays, for example > "linux,keymap" in Documentation/devicetree/bindings/input/matrix-keymap.txt. That does not answer my question: Do all maxTouch touchpads (or specifically that in Spring) need eight entries, padded with said KEY_RESERVED? In my experiments using just six entries (i.e., until the non-zero entry) worked okay - so does this T19 message have specifically eight bits? Tegra used just four entries iirc. >> With my above snippet I got an awful lot of "Interrupt triggered but >> zero messages" warnings (which I simply commented out as quickfix). >> Is that why you are using _EDGE_FALLING? Or pin-function 0xf? >> (In my case the ChromeOS DT had IRQ_TYPE_NONE and pin-function 0x0.) >> > > These are two separate but related things: > > a) IRQF_TRIGGER_FALLING: > > Yes, the Chrome OS DT for Peach Pit also has IRQ_TYPE_NONE but the DTS is > not correct. > > If you look at the Chrome OS atmel driver > (drivers/input/touchscreen/atmel_mxt_ts.c), it passes IRQF_TRIGGER_FALLING > to request_threaded_irq(): > > /* Default to falling edge if no platform data provided */ > irqflags = data->pdata ? data->pdata->irqflags : IRQF_TRIGGER_FALLING; > error = request_threaded_irq(client->irq, NULL, mxt_interrupt, > irqflags | IRQF_ONESHOT, > client->name, data); > > The above code is wrong since is overwriting the edge/level type flags set > by OF when parsing the "interrupts" property so you have to use the > expected IRQ flags in your DTS. > > b) pin-function 0xf instead of 0x0: > > The pin-function 0x0 is GPIO input while 0xf is GPIO IRQ. Usually on other > SoCs to use a GPIO IRQ you just configure the pad as GPIO input and then > enable the pin as an interrupt but on Exynos SoC these are really two > different functions. So if you configure the pin as GPIO input and this > happens after the pin is configured as GPIO IRQ, interrupts are not triggered. > > I faced that issue before [1] and was solved with Tomasz's commit: > > f6a8249 pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs > > which changes the pinctrl-exynos driver to setup a pin as GPIO IRQ on > .irq_request_resources instead of .irq_set_type. So, with that patch even > when pin-function re-configures the function to GPIO input, is then > configured as GPIO IRQ when request_threaded_irq() is called. > > So probably is working for you just because you tested on linux-next that > already has Tomasz's changes but still the correct thing to do is to setup > the pin as 0xf. This change probably is needed on other pins used as GPIO > IRQ that are using 0x0 now. > > Sorry, the email became longer than I wanted but I hope is helpful to you. Thanks for the explanations, I'll test those settings on Spring then. Could you point me to what ChromeOS tree and branch I should be looking at? For instance, the linux-next.git chromeos-3.8 branch did not have any DT for Spring. Therefore my series is based on /proc/device-tree rather than any ChromeOS source code. Thanks, Andreas
Hello Andreas, On 08/27/2014 03:11 PM, Andreas Färber wrote: > Hi Javier, >>> >>> + trackpad@4b { >>> + compatible = "atmel,maxtouch"; >>> + reg = <0x4b>; >>> + interrupt-parent = <&gpx1>; >>> + interrupts = <2 IRQ_TYPE_NONE>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&trackpad_irq>; >>> + linux,gpio-keymap = <KEY_RESERVED >>> + KEY_RESERVED >>> + KEY_RESERVED >>> + KEY_RESERVED >>> + KEY_RESERVED >>> + BTN_LEFT>; >>> + wakeup-source; >>> + }; >>> >>> 0 == KEY_RESERVED, so you can consistently use it for GPIO 0-2, too. :) >>> >> >> I know that the value of KEY_RESERVED is 0 but I didn't use KEY_RESERVED >> for the GPIO on purpose. >> >> What I understood is that the SPT_GPIOPWN_T19 object sends messages using >> a status byte so you have a maximum of 8 GPIO but not every maXTouch >> devices use all of them. So in the particular case of the device in the >> Peach Pit, from the 8 possible GPIO only 4 can be used and these are pins >> 2-5. So in theory you could connect 3 more GPIO in case you had more >> buttons (e.g: BTN_RIGHT, BTN_MIDDLE) but only 1 is used since the >> Chromebook just have BTN_LEFT. > > FWIW when I press to the bottom right of my touchpad, I do get > right-click functionality even with just BTN_LEFT specified in the > keymap. Magic. :) > Right, I'm not an expert in input but after asking a colleague he explained to me that user-space input drivers deal with the MT tracking for you, but there is still a single event code reported (BTN_LEFT) as an indication that the touchpad has been physically clicked. That's why you are having right click even when the hardware is not reporting it. You can confirm that by running plain evdev or by clicking on the touchpad using an object (e.g: a pencil) so ABS_MT_* events won't be reported. >> Nick sent a patch [0] that extend the atmel touchpad DT binding and the >> doc says "Use KEY_RESERVED for unused padding values". But is not clear >> what value you should use for GPIO that are actually supported by the >> device but have no keycode associated. >> >> So by using 0 instead of KEY_RESERVED I wanted to document that pins 2-4 >> are actually supported and not reserved by the device but there is no >> keycode associated with that GPIO. > > You already documented that via comments though. > Yes but still I don't like to use KEY_RESERVED for all the pins since some of them are not really reserved. Can we agree on disagree here and after Nick answer I can post as a follow-up patch after this series gets merged? >> If there was a BTN_NONE or KEY_UNUSED it would had been better but I think >> that making a distinction between these two cases (reserved pin vs GPIO >> available but not used) is useful. > > Maybe Nick can comment here. > >>> I probably should add the two trailing _RESERVEDs, too? >>> >> >> I see that is used for properties that are arrays, for example >> "linux,keymap" in Documentation/devicetree/bindings/input/matrix-keymap.txt. > > That does not answer my question: Do all maxTouch touchpads (or > specifically that in Spring) need eight entries, padded with said > KEY_RESERVED? In my experiments using just six entries (i.e., until the > non-zero entry) worked okay - so does this T19 message have specifically > eight bits? Tegra used just four entries iirc. > I guess there are other touchpads that have a different offset (e.g: using the last 4 pins) so I think that is good as a way of documenting the layout even if not strictly necessary for the driver. But again, without proper documentation is hard to say so I'll let Nick to answer that. >>> With my above snippet I got an awful lot of "Interrupt triggered but >>> zero messages" warnings (which I simply commented out as quickfix). >>> Is that why you are using _EDGE_FALLING? Or pin-function 0xf? >>> (In my case the ChromeOS DT had IRQ_TYPE_NONE and pin-function 0x0.) >>> >> >> These are two separate but related things: >> >> a) IRQF_TRIGGER_FALLING: >> >> Yes, the Chrome OS DT for Peach Pit also has IRQ_TYPE_NONE but the DTS is >> not correct. >> >> If you look at the Chrome OS atmel driver >> (drivers/input/touchscreen/atmel_mxt_ts.c), it passes IRQF_TRIGGER_FALLING >> to request_threaded_irq(): >> >> /* Default to falling edge if no platform data provided */ >> irqflags = data->pdata ? data->pdata->irqflags : IRQF_TRIGGER_FALLING; >> error = request_threaded_irq(client->irq, NULL, mxt_interrupt, >> irqflags | IRQF_ONESHOT, >> client->name, data); >> >> The above code is wrong since is overwriting the edge/level type flags set >> by OF when parsing the "interrupts" property so you have to use the >> expected IRQ flags in your DTS. >> >> b) pin-function 0xf instead of 0x0: >> >> The pin-function 0x0 is GPIO input while 0xf is GPIO IRQ. Usually on other >> SoCs to use a GPIO IRQ you just configure the pad as GPIO input and then >> enable the pin as an interrupt but on Exynos SoC these are really two >> different functions. So if you configure the pin as GPIO input and this >> happens after the pin is configured as GPIO IRQ, interrupts are not triggered. >> >> I faced that issue before [1] and was solved with Tomasz's commit: >> >> f6a8249 pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs >> >> which changes the pinctrl-exynos driver to setup a pin as GPIO IRQ on >> .irq_request_resources instead of .irq_set_type. So, with that patch even >> when pin-function re-configures the function to GPIO input, is then >> configured as GPIO IRQ when request_threaded_irq() is called. >> >> So probably is working for you just because you tested on linux-next that >> already has Tomasz's changes but still the correct thing to do is to setup >> the pin as 0xf. This change probably is needed on other pins used as GPIO >> IRQ that are using 0x0 now. >> >> Sorry, the email became longer than I wanted but I hope is helpful to you. > > Thanks for the explanations, I'll test those settings on Spring then. > > Could you point me to what ChromeOS tree and branch I should be looking > at? For instance, the linux-next.git chromeos-3.8 branch did not have > any DT for Spring. Therefore my series is based on /proc/device-tree > rather than any ChromeOS source code. > I use as a reference https://chromium.googlesource.com/chromiumos/third_party/kernel branch chromeos-3.8 > Thanks, > Andreas > Best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 27/08/14 15:22, Javier Martinez Canillas wrote: >>> If there was a BTN_NONE or KEY_UNUSED it would had been better but I think >>> that making a distinction between these two cases (reserved pin vs GPIO >>> available but not used) is useful. >> >> Maybe Nick can comment here. Yes, this is probably useful to document. However, I fear that it's not going to be obvious what the distinction is to someone who doesn't have the Atmel docs. Perhaps it would be clearer to just do something like: linux,gpio-keymap = <KEY_RESERVED KEY_RESERVED KEY_RESERVED /* GPIO0 */ KEY_RESERVED /* GPIO1 */ KEY_RESERVED /* GPIO2 */ BTN_LEFT>; /* GPIO3 */ If you omit any trailing KEY_RESERVED values it doesn't affect anything. I was also going to suggest that you put something like "/* Atmel mXT224SL */" in your .dts file so it's clear what version of the maXTouch device you are configuring. -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello Nick, On 09/02/2014 03:46 PM, Nick Dyer wrote: > On 27/08/14 15:22, Javier Martinez Canillas wrote: >>>> If there was a BTN_NONE or KEY_UNUSED it would had been better but I think >>>> that making a distinction between these two cases (reserved pin vs GPIO >>>> available but not used) is useful. >>> >>> Maybe Nick can comment here. > > Yes, this is probably useful to document. However, I fear that it's not > going to be obvious what the distinction is to someone who doesn't have the > Atmel docs. Perhaps it would be clearer to just do something like: > > linux,gpio-keymap = <KEY_RESERVED > KEY_RESERVED > KEY_RESERVED /* GPIO0 */ > KEY_RESERVED /* GPIO1 */ > KEY_RESERVED /* GPIO2 */ > BTN_LEFT>; /* GPIO3 */ > > If you omit any trailing KEY_RESERVED values it doesn't affect anything. > > I was also going to suggest that you put something like "/* Atmel mXT224SL > */" in your .dts file so it's clear what version of the maXTouch device you > are configuring. > Ok, I'll re-spin with those changes. Thanks a lot for your feedback. Best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 228a6b1..e4f82d5 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -11,6 +11,7 @@ /dts-v1/; #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> #include "exynos5420.dtsi" / { @@ -157,6 +158,29 @@ }; }; +&hsi2c_8 { + status = "okay"; + clock-frequency = <333000>; + + trackpad@4b { + compatible="atmel,maxtouch"; + reg=<0x4b>; + interrupt-parent=<&gpx1>; + interrupts=<1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + pinctrl-names = "default"; + pinctrl-0 = <&trackpad_irq>; + linux,gpio-keymap = < KEY_RESERVED + KEY_RESERVED + 0 /* GPIO 0 */ + 0 /* GPIO 1 */ + 0 /* GPIO 2 */ + BTN_LEFT /* GPIO 3 */ + KEY_RESERVED + KEY_RESERVED >; + }; +}; + &hsi2c_9 { status = "okay"; clock-frequency = <400000>; @@ -249,6 +273,13 @@ samsung,pin-drv = <0>; }; + trackpad_irq: trackpad-irq { + samsung,pins = "gpx1-1"; + samsung,pin-function = <0xf>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + power_key_irq: power-key-irq { samsung,pins = "gpx1-2"; samsung,pin-function = <0>;