@@ -90,7 +90,17 @@
#define PHYCLKRST_COMMONONN BIT(0)
#define EXYNOS5_DRD_PHYREG0 0x14
+#define PHYREG0_SSC_REF_CLK_SEL BIT(21)
+#define PHYREG0_SSC_RANGE BIT(20)
+#define PHYREG0_CR_WRITE BIT(19)
+#define PHYREG0_CR_READ BIT(18)
+#define PHYREG0_CR_DATA_IN(_x) ((_x) << 2)
+#define PHYREG0_CR_CAP_DATA BIT(1)
+#define PHYREG0_CR_CAP_ADDR BIT(0)
+
#define EXYNOS5_DRD_PHYREG1 0x18
+#define PHYREG1_CR_DATA_OUT(_x) ((_x) << 1)
+#define PHYREG1_CR_ACK BIT(0)
#define EXYNOS5_DRD_PHYPARAM0 0x1c
@@ -119,6 +129,25 @@
#define EXYNOS5_DRD_PHYRESUME 0x34
#define EXYNOS5_DRD_LINKPORT 0x44
+/* USB 3.0 DRD PHY SS Function Control Reg; accessed by CR_PORT */
+#define EXYNOS5_DRD_PHYSS_LOSLEVEL_OVRD_IN (0x15)
+#define LOSLEVEL_OVRD_IN_LOS_BIAS_5420 (0x5 << 13)
+#define LOSLEVEL_OVRD_IN_LOS_BIAS_DEFAULT (0x0 << 13)
+#define LOSLEVEL_OVRD_IN_EN (0x1 << 10)
+#define LOSLEVEL_OVRD_IN_LOS_LEVEL_DEFAULT (0x9 << 0)
+
+#define EXYNOS5_DRD_PHYSS_TX_VBOOSTLEVEL_OVRD_IN (0x12)
+#define TX_VBOOSTLEVEL_OVRD_IN_VBOOST_5420 (0x5 << 13)
+#define TX_VBOOSTLEVEL_OVRD_IN_VBOOST_DEFAULT (0x4 << 13)
+
+#define EXYNOS5_DRD_PHYSS_LANE0_TX_DEBUG (0x1010)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_19M2_20M (0x4 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_24M (0x8 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_25M_26M (0x8 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_48M_50M_52M (0x20 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_62M5 (0x20 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_96M_100M (0x40 << 4)
+
#define KHZ 1000
#define MHZ (KHZ * KHZ)
@@ -527,6 +556,151 @@ static int exynos5_usbdrd_phy_power_off(struct phy *phy)
return 0;
}
+static int crport_handshake(struct exynos5_usbdrd_phy *phy_drd,
+ u32 val, u32 cmd)
+{
+ u32 usec = 100;
+ unsigned int result;
+
+ writel(val | cmd, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+
+ do {
+ result = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYREG1);
+ if (result & PHYREG1_CR_ACK)
+ break;
+
+ udelay(1);
+ } while (usec-- > 0);
+
+ if (!usec) {
+ dev_err(phy_drd->dev,
+ "CRPORT handshake timeout1 (0x%08x)\n", val);
+ return -ETIME;
+ }
+
+ usec = 100;
+
+ writel(val, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+
+ do {
+ result = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYREG1);
+ if (!(result & PHYREG1_CR_ACK))
+ break;
+
+ udelay(1);
+ } while (usec-- > 0);
+
+ if (!usec) {
+ dev_err(phy_drd->dev,
+ "CRPORT handshake timeout2 (0x%08x)\n", val);
+ return -ETIME;
+ }
+
+ return 0;
+}
+
+static int crport_ctrl_write(struct exynos5_usbdrd_phy *phy_drd,
+ u32 addr, u32 data)
+{
+ int ret;
+
+ /* Write Address */
+ writel(PHYREG0_CR_DATA_IN(addr),
+ phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+ ret = crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(addr),
+ PHYREG0_CR_CAP_ADDR);
+ if (ret)
+ return ret;
+
+ /* Write Data */
+ writel(PHYREG0_CR_DATA_IN(data),
+ phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+ ret = crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(data),
+ PHYREG0_CR_CAP_DATA);
+ if (ret)
+ return ret;
+
+ ret = crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(data),
+ PHYREG0_CR_WRITE);
+
+ return ret;
+}
+
+/*
+ * Calibrate few PHY parameters using CR_PORT register to meet
+ * SuperSpeed requirements on Exynos5420 and Exynos5800 systems,
+ * which have 28nm USB 3.0 DRD PHY.
+ */
+static int exynos5420_usbdrd_phy_calibrate(struct exynos5_usbdrd_phy *phy_drd)
+{
+ unsigned int temp;
+ int ret = 0;
+
+ /*
+ * Change los_bias to (0x5) for 28nm PHY from a
+ * default value (0x0); los_level is set as default
+ * (0x9) as also reflected in los_level[30:26] bits
+ * of PHYPARAM0 register.
+ */
+ temp = LOSLEVEL_OVRD_IN_LOS_BIAS_5420 |
+ LOSLEVEL_OVRD_IN_EN |
+ LOSLEVEL_OVRD_IN_LOS_LEVEL_DEFAULT;
+ ret = crport_ctrl_write(phy_drd,
+ EXYNOS5_DRD_PHYSS_LOSLEVEL_OVRD_IN,
+ temp);
+ if (ret) {
+ dev_err(phy_drd->dev,
+ "Failed setting Loss-of-Signal level for SuperSpeed\n");
+ return ret;
+ }
+
+ /*
+ * Set tx_vboost_lvl to (0x5) for 28nm PHY Tuning,
+ * to raise Tx signal level from its default value of (0x4)
+ */
+ temp = TX_VBOOSTLEVEL_OVRD_IN_VBOOST_5420;
+ ret = crport_ctrl_write(phy_drd,
+ EXYNOS5_DRD_PHYSS_TX_VBOOSTLEVEL_OVRD_IN,
+ temp);
+ if (ret) {
+ dev_err(phy_drd->dev,
+ "Failed setting Tx-Vboost-Level for SuperSpeed\n");
+ return ret;
+ }
+
+ /*
+ * Set proper time to wait for RxDetect measurement, for
+ * desired reference clock of PHY, by tuning the CR_PORT
+ * register LANE0.TX_DEBUG which is internal to PHY.
+ * This fixes issue with few USB 3.0 devices, which are
+ * not detected (not even generate interrupts on the bus
+ * on insertion) without this change.
+ * e.g. Samsung SUM-TSB16S 3.0 USB drive.
+ */
+ switch (phy_drd->extrefclk) {
+ case EXYNOS5_FSEL_50MHZ:
+ temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_48M_50M_52M;
+ break;
+ case EXYNOS5_FSEL_20MHZ:
+ case EXYNOS5_FSEL_19MHZ2:
+ temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_19M2_20M;
+ break;
+ case EXYNOS5_FSEL_24MHZ:
+ default:
+ temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_24M;
+ break;
+ }
+
+ ret = crport_ctrl_write(phy_drd,
+ EXYNOS5_DRD_PHYSS_LANE0_TX_DEBUG,
+ temp);
+ if (ret)
+ dev_err(phy_drd->dev,
+ "Failed setting RxDetect measurement time for SuperSpeed\n");
+
+ return ret;
+}
+
static struct phy *exynos5_usbdrd_phy_xlate(struct device *dev,
struct of_phandle_args *args)
{
@@ -538,11 +712,20 @@ static struct phy *exynos5_usbdrd_phy_xlate(struct device *dev,
return phy_drd->phys[args->args[0]].phy;
}
+static int exynos5_usbdrd_phy_calibrate(struct phy *phy)
+{
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+ return exynos5420_usbdrd_phy_calibrate(phy_drd);
+}
+
static const struct phy_ops exynos5_usbdrd_phy_ops = {
.init = exynos5_usbdrd_phy_init,
.exit = exynos5_usbdrd_phy_exit,
.power_on = exynos5_usbdrd_phy_power_on,
.power_off = exynos5_usbdrd_phy_power_off,
+ .calibrate = exynos5_usbdrd_phy_calibrate,
.owner = THIS_MODULE,
};
@@ -156,9 +156,10 @@ static void __dwc3_set_mode(struct work_struct *work)
} else {
if (dwc->usb2_phy)
otg_set_vbus(dwc->usb2_phy->otg, true);
- if (dwc->usb2_generic_phy)
+ if (dwc->usb2_generic_phy) {
phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
-
+ phy_calibrate(dwc->usb2_generic_phy);
+ }
}
break;
case DWC3_GCTL_PRTCAP_DEVICE:
@@ -955,6 +956,8 @@ static int dwc3_core_init_mode(struct dwc3 *dwc)
dev_err(dev, "failed to initialize host\n");
return ret;
}
+ if (dwc->usb2_generic_phy)
+ phy_calibrate(dwc->usb2_generic_phy);
break;
case USB_DR_MODE_OTG:
INIT_WORK(&dwc->drd_work, __dwc3_set_mode);