| Message ID | 1527500833-16005-8-git-send-email-m.purski@samsung.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
Hi Maciej, Thank you for the patch. On Monday, 28 May 2018 12:47:11 EEST Maciej Purski wrote: > The patch adds bindings to Toshiba DSI/LVDS bridge TC358764. > Bindings describe power supplies, reset gpio and video interfaces. > > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Maciej Purski <m.purski@samsung.com> > --- > .../bindings/display/bridge/toshiba,tc358764.txt | 42 +++++++++++++++++++ > 1 file changed, 42 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > > diff --git > a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt new > file mode 100644 > index 0000000..d09bdc2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > @@ -0,0 +1,42 @@ > +TC358764 MIPI-DSI to LVDS panel bridge > + > +Required properties: > + - compatible: "toshiba,tc358764" > + - reg: the virtual channel number of a DSI peripheral > + - vddc-supply: core voltage supply > + - vddio-supply: I/O voltage supply > + - vddmipi-supply: MIPI voltage supply > + - vddlvds133-supply: LVDS1 3.3V voltage supply > + - vddlvds112-supply: LVDS1 1.2V voltage supply That's a lot of power supplies. Could some of them be merged together ? See https://patchwork.freedesktop.org/patch/216058/ for an earlier discussion on the same subject. > + - reset-gpios: a GPIO spec for the reset pin > + > +The device node can contain zero to two 'port' child nodes, each with one > +child > +'endpoint' node, according to the bindings defined in [1]. > +The following are properties specific to those nodes. > + > +port: > + - reg: (required) can be 0 for DSI port or 1 for LVDS port; This seems pretty vague to me. It could be read as meaning that ports are completely optional, and that the port number you list can be used, but that something else could be used to. Let's make the port nodes mandatory. I propose the following. Required nodes: The TC358764 has DSI and LVDS ports whose connections are described using the OF graph bindings defined in Documentation/devicetree/bindings/graph.txt. The device node must contain one 'port' child node per DSI and LVDS port. The port nodes are numbered as follows. Port Number ------------------------------------------------------------------- DSI Input 0 LVDS Output 1 Each port node must contain endpoint nodes describing the hardware connections. > +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt > + > +Example: > + > + bridge@0 { > + reg = <0>; > + compatible = "toshiba,tc358764"; > + vddc-supply = <&vcc_1v2_reg>; > + vddio-supply = <&vcc_1v8_reg>; > + vddmipi-supply = <&vcc_1v2_reg>; > + vddlvds133-supply = <&vcc_3v3_reg>; > + vddlvds112-supply = <&vcc_1v2_reg>; > + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; > + #address-cells = <1>; > + #size-cells = <0>; > + port@1 { > + reg = <1>; > + lvds_ep: endpoint { > + remote-endpoint = <&panel_ep>; > + }; > + }; > + };
On 28.05.2018 12:18, Laurent Pinchart wrote: > Hi Maciej, > > Thank you for the patch. > > On Monday, 28 May 2018 12:47:11 EEST Maciej Purski wrote: >> The patch adds bindings to Toshiba DSI/LVDS bridge TC358764. >> Bindings describe power supplies, reset gpio and video interfaces. >> >> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> >> Signed-off-by: Maciej Purski <m.purski@samsung.com> >> --- >> .../bindings/display/bridge/toshiba,tc358764.txt | 42 +++++++++++++++++++ >> 1 file changed, 42 insertions(+) >> create mode 100644 >> Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >> >> diff --git >> a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt new >> file mode 100644 >> index 0000000..d09bdc2 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >> @@ -0,0 +1,42 @@ >> +TC358764 MIPI-DSI to LVDS panel bridge >> + >> +Required properties: >> + - compatible: "toshiba,tc358764" >> + - reg: the virtual channel number of a DSI peripheral >> + - vddc-supply: core voltage supply >> + - vddio-supply: I/O voltage supply >> + - vddmipi-supply: MIPI voltage supply >> + - vddlvds133-supply: LVDS1 3.3V voltage supply >> + - vddlvds112-supply: LVDS1 1.2V voltage supply > That's a lot of power supplies. Could some of them be merged together ? See > https://patchwork.freedesktop.org/patch/216058/ for an earlier discussion on > the same subject. Specs says about 3 supply voltage values: - 1.2V - digital core, DSI-RX PHY - 1.8-3.3V - digital I/O - 3.3V - LVDS-TX PHY So I guess it should be minimal number of supplies. Natural candidates: - vddc-supply: core voltage supply, 1.2V - vddio-supply: I/O voltage supply, 1.8V or 3.3V - vddlvds-supply: LVDS1/2 voltage supply, 3.3V I have changed name of the latest supply to be more consistent with other supplies, and changed 1.8-3.3 (which incorrectly suggest voltage range), to more precise voltage alternative. > >> + - reset-gpios: a GPIO spec for the reset pin >> + >> +The device node can contain zero to two 'port' child nodes, each with one >> +child >> +'endpoint' node, according to the bindings defined in [1]. >> +The following are properties specific to those nodes. >> + >> +port: >> + - reg: (required) can be 0 for DSI port or 1 for LVDS port; > This seems pretty vague to me. It could be read as meaning that ports are > completely optional, and that the port number you list can be used, but that > something else could be used to. > > Let's make the port nodes mandatory. I propose the following. > > Required nodes: > > The TC358764 has DSI and LVDS ports whose connections are described using the > OF graph bindings defined in Documentation/devicetree/bindings/graph.txt. The > device node must contain one 'port' child node per DSI and LVDS port. The port > nodes are numbered as follows. > > Port Number > ------------------------------------------------------------------- > DSI Input 0 > LVDS Output 1 > > Each port node must contain endpoint nodes describing the hardware > connections. Since the bridge is controlled via DSI bus, DSI input port is not necessary. Regards Andrzej > >> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt >> + >> +Example: >> + >> + bridge@0 { >> + reg = <0>; >> + compatible = "toshiba,tc358764"; >> + vddc-supply = <&vcc_1v2_reg>; >> + vddio-supply = <&vcc_1v8_reg>; >> + vddmipi-supply = <&vcc_1v2_reg>; >> + vddlvds133-supply = <&vcc_3v3_reg>; >> + vddlvds112-supply = <&vcc_1v2_reg>; >> + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + port@1 { >> + reg = <1>; >> + lvds_ep: endpoint { >> + remote-endpoint = <&panel_ep>; >> + }; >> + }; >> + }; -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Andrzej, On Wednesday, 30 May 2018 12:59:12 EEST Andrzej Hajda wrote: > On 28.05.2018 12:18, Laurent Pinchart wrote: > > On Monday, 28 May 2018 12:47:11 EEST Maciej Purski wrote: > >> The patch adds bindings to Toshiba DSI/LVDS bridge TC358764. > >> Bindings describe power supplies, reset gpio and video interfaces. > >> > >> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > >> Signed-off-by: Maciej Purski <m.purski@samsung.com> > >> --- > >> > >> .../bindings/display/bridge/toshiba,tc358764.txt | 42 ++++++++++++++++ > >> 1 file changed, 42 insertions(+) > >> create mode 100644 > >> > >> Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >> > >> diff --git > >> a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >> new > >> file mode 100644 > >> index 0000000..d09bdc2 > >> --- /dev/null > >> +++ > >> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >> @@ -0,0 +1,42 @@ > >> +TC358764 MIPI-DSI to LVDS panel bridge > >> + > >> +Required properties: > >> + - compatible: "toshiba,tc358764" > >> + - reg: the virtual channel number of a DSI peripheral > >> + - vddc-supply: core voltage supply > >> + - vddio-supply: I/O voltage supply > >> + - vddmipi-supply: MIPI voltage supply > >> + - vddlvds133-supply: LVDS1 3.3V voltage supply > >> + - vddlvds112-supply: LVDS1 1.2V voltage supply > > > > That's a lot of power supplies. Could some of them be merged together ? > > See https://patchwork.freedesktop.org/patch/216058/ for an earlier > > discussion on the same subject. > > Specs says about 3 supply voltage values: > - 1.2V - digital core, DSI-RX PHY > - 1.8-3.3V - digital I/O > - 3.3V - LVDS-TX PHY > > So I guess it should be minimal number of supplies. Natural candidates: > > - vddc-supply: core voltage supply, 1.2V > - vddio-supply: I/O voltage supply, 1.8V or 3.3V > - vddlvds-supply: LVDS1/2 voltage supply, 3.3V > > I have changed name of the latest supply to be more consistent with > other supplies, and changed 1.8-3.3 (which incorrectly suggest voltage > range), to more precise voltage alternative. This looks fine to me. > >> + - reset-gpios: a GPIO spec for the reset pin > >> + > >> +The device node can contain zero to two 'port' child nodes, each with > >> one > >> +child > >> +'endpoint' node, according to the bindings defined in [1]. > >> +The following are properties specific to those nodes. > >> + > >> +port: > >> + - reg: (required) can be 0 for DSI port or 1 for LVDS port; > > > > This seems pretty vague to me. It could be read as meaning that ports are > > completely optional, and that the port number you list can be used, but > > that something else could be used to. > > > > Let's make the port nodes mandatory. I propose the following. > > > > Required nodes: > > > > The TC358764 has DSI and LVDS ports whose connections are described using > > the OF graph bindings defined in > > Documentation/devicetree/bindings/graph.txt. The device node must contain > > one 'port' child node per DSI and LVDS port. The port nodes are numbered > > as follows. > > > > Port Number > > ------------------------------------------------------------------- > > DSI Input 0 > > LVDS Output 1 > > > > Each port node must contain endpoint nodes describing the hardware > > connections. > > Since the bridge is controlled via DSI bus, DSI input port is not necessary. I don't agree with this. Regardless of how the bridge is controlled, I think we should always use ports to describe the data connections. Otherwise it would get more complicated for display controller drivers to use different types of bridges. > >> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt > >> + > >> +Example: > >> + > >> + bridge@0 { > >> + reg = <0>; > >> + compatible = "toshiba,tc358764"; > >> + vddc-supply = <&vcc_1v2_reg>; > >> + vddio-supply = <&vcc_1v8_reg>; > >> + vddmipi-supply = <&vcc_1v2_reg>; > >> + vddlvds133-supply = <&vcc_3v3_reg>; > >> + vddlvds112-supply = <&vcc_1v2_reg>; > >> + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + port@1 { > >> + reg = <1>; > >> + lvds_ep: endpoint { > >> + remote-endpoint = <&panel_ep>; > >> + }; > >> + }; > >> + };
On 30.05.2018 14:35, Laurent Pinchart wrote: > Hi Andrzej, > > On Wednesday, 30 May 2018 12:59:12 EEST Andrzej Hajda wrote: >> On 28.05.2018 12:18, Laurent Pinchart wrote: >>> On Monday, 28 May 2018 12:47:11 EEST Maciej Purski wrote: >>>> The patch adds bindings to Toshiba DSI/LVDS bridge TC358764. >>>> Bindings describe power supplies, reset gpio and video interfaces. >>>> >>>> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> >>>> Signed-off-by: Maciej Purski <m.purski@samsung.com> >>>> --- >>>> >>>> .../bindings/display/bridge/toshiba,tc358764.txt | 42 ++++++++++++++++ >>>> 1 file changed, 42 insertions(+) >>>> create mode 100644 >>>> >>>> Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> >>>> diff --git >>>> a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> new >>>> file mode 100644 >>>> index 0000000..d09bdc2 >>>> --- /dev/null >>>> +++ >>>> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> @@ -0,0 +1,42 @@ >>>> +TC358764 MIPI-DSI to LVDS panel bridge >>>> + >>>> +Required properties: >>>> + - compatible: "toshiba,tc358764" >>>> + - reg: the virtual channel number of a DSI peripheral >>>> + - vddc-supply: core voltage supply >>>> + - vddio-supply: I/O voltage supply >>>> + - vddmipi-supply: MIPI voltage supply >>>> + - vddlvds133-supply: LVDS1 3.3V voltage supply >>>> + - vddlvds112-supply: LVDS1 1.2V voltage supply >>> That's a lot of power supplies. Could some of them be merged together ? >>> See https://patchwork.freedesktop.org/patch/216058/ for an earlier >>> discussion on the same subject. >> Specs says about 3 supply voltage values: >> - 1.2V - digital core, DSI-RX PHY >> - 1.8-3.3V - digital I/O >> - 3.3V - LVDS-TX PHY >> >> So I guess it should be minimal number of supplies. Natural candidates: >> >> - vddc-supply: core voltage supply, 1.2V >> - vddio-supply: I/O voltage supply, 1.8V or 3.3V >> - vddlvds-supply: LVDS1/2 voltage supply, 3.3V >> >> I have changed name of the latest supply to be more consistent with >> other supplies, and changed 1.8-3.3 (which incorrectly suggest voltage >> range), to more precise voltage alternative. > This looks fine to me. > >>>> + - reset-gpios: a GPIO spec for the reset pin >>>> + >>>> +The device node can contain zero to two 'port' child nodes, each with >>>> one >>>> +child >>>> +'endpoint' node, according to the bindings defined in [1]. >>>> +The following are properties specific to those nodes. >>>> + >>>> +port: >>>> + - reg: (required) can be 0 for DSI port or 1 for LVDS port; >>> This seems pretty vague to me. It could be read as meaning that ports are >>> completely optional, and that the port number you list can be used, but >>> that something else could be used to. >>> >>> Let's make the port nodes mandatory. I propose the following. >>> >>> Required nodes: >>> >>> The TC358764 has DSI and LVDS ports whose connections are described using >>> the OF graph bindings defined in >>> Documentation/devicetree/bindings/graph.txt. The device node must contain >>> one 'port' child node per DSI and LVDS port. The port nodes are numbered >>> as follows. >>> >>> Port Number >>> ------------------------------------------------------------------- >>> DSI Input 0 >>> LVDS Output 1 >>> >>> Each port node must contain endpoint nodes describing the hardware >>> connections. >> Since the bridge is controlled via DSI bus, DSI input port is not necessary. > I don't agree with this. Regardless of how the bridge is controlled, I think > we should always use ports to describe the data connections. Otherwise it > would get more complicated for display controller drivers to use different > types of bridges. It was discussed already, and DT guideline is to skip graphs in simple case of parent/child nodes, see for example [1]. [1]: https://marc.info/?l=dri-devel&m=148354108702517&w=2 Regards Andrzej >>>> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt >>>> + >>>> +Example: >>>> + >>>> + bridge@0 { >>>> + reg = <0>; >>>> + compatible = "toshiba,tc358764"; >>>> + vddc-supply = <&vcc_1v2_reg>; >>>> + vddio-supply = <&vcc_1v8_reg>; >>>> + vddmipi-supply = <&vcc_1v2_reg>; >>>> + vddlvds133-supply = <&vcc_3v3_reg>; >>>> + vddlvds112-supply = <&vcc_1v2_reg>; >>>> + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; >>>> + #address-cells = <1>; >>>> + #size-cells = <0>; >>>> + port@1 { >>>> + reg = <1>; >>>> + lvds_ep: endpoint { >>>> + remote-endpoint = <&panel_ep>; >>>> + }; >>>> + }; >>>> + }; -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Andrzej, On Wednesday, 30 May 2018 16:07:29 EEST Andrzej Hajda wrote: > On 30.05.2018 14:35, Laurent Pinchart wrote: > > On Wednesday, 30 May 2018 12:59:12 EEST Andrzej Hajda wrote: > >> On 28.05.2018 12:18, Laurent Pinchart wrote: > >>> On Monday, 28 May 2018 12:47:11 EEST Maciej Purski wrote: > >>>> The patch adds bindings to Toshiba DSI/LVDS bridge TC358764. > >>>> Bindings describe power supplies, reset gpio and video interfaces. > >>>> > >>>> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > >>>> Signed-off-by: Maciej Purski <m.purski@samsung.com> > >>>> --- > >>>> > >>>> .../bindings/display/bridge/toshiba,tc358764.txt | 42 > >>>> ++++++++++++++++ > >>>> 1 file changed, 42 insertions(+) > >>>> create mode 100644 > >>>> > >>>> Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >>>> > >>>> diff --git > >>>> a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >>>> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >>>> new > >>>> file mode 100644 > >>>> index 0000000..d09bdc2 > >>>> --- /dev/null > >>>> +++ > >>>> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > >>>> @@ -0,0 +1,42 @@ > >>>> +TC358764 MIPI-DSI to LVDS panel bridge > >>>> + > >>>> +Required properties: > >>>> + - compatible: "toshiba,tc358764" > >>>> + - reg: the virtual channel number of a DSI peripheral > >>>> + - vddc-supply: core voltage supply > >>>> + - vddio-supply: I/O voltage supply > >>>> + - vddmipi-supply: MIPI voltage supply > >>>> + - vddlvds133-supply: LVDS1 3.3V voltage supply > >>>> + - vddlvds112-supply: LVDS1 1.2V voltage supply > >>> > >>> That's a lot of power supplies. Could some of them be merged together ? > >>> See https://patchwork.freedesktop.org/patch/216058/ for an earlier > >>> discussion on the same subject. > >> > >> Specs says about 3 supply voltage values: > >> - 1.2V - digital core, DSI-RX PHY > >> - 1.8-3.3V - digital I/O > >> - 3.3V - LVDS-TX PHY > >> > >> So I guess it should be minimal number of supplies. Natural candidates: > >> > >> - vddc-supply: core voltage supply, 1.2V > >> - vddio-supply: I/O voltage supply, 1.8V or 3.3V > >> - vddlvds-supply: LVDS1/2 voltage supply, 3.3V > >> > >> I have changed name of the latest supply to be more consistent with > >> other supplies, and changed 1.8-3.3 (which incorrectly suggest voltage > >> range), to more precise voltage alternative. > > > > This looks fine to me. > > > >>>> + - reset-gpios: a GPIO spec for the reset pin > >>>> + > >>>> +The device node can contain zero to two 'port' child nodes, each with > >>>> one > >>>> +child > >>>> +'endpoint' node, according to the bindings defined in [1]. > >>>> +The following are properties specific to those nodes. > >>>> + > >>>> +port: > >>>> + - reg: (required) can be 0 for DSI port or 1 for LVDS port; > >>> > >>> This seems pretty vague to me. It could be read as meaning that ports > >>> are > >>> completely optional, and that the port number you list can be used, but > >>> that something else could be used to. > >>> > >>> Let's make the port nodes mandatory. I propose the following. > >>> > >>> Required nodes: > >>> > >>> The TC358764 has DSI and LVDS ports whose connections are described > >>> using > >>> the OF graph bindings defined in > >>> Documentation/devicetree/bindings/graph.txt. The device node must > >>> contain > >>> one 'port' child node per DSI and LVDS port. The port nodes are numbered > >>> as follows. > >>> > >>> Port Number > >>> > >>> ------------------------------------------------------------------- > >>> > >>> DSI Input 0 > >>> LVDS Output 1 > >>> > >>> Each port node must contain endpoint nodes describing the hardware > >>> connections. > >> > >> Since the bridge is controlled via DSI bus, DSI input port is not > >> necessary. > > > > I don't agree with this. Regardless of how the bridge is controlled, I > > think we should always use ports to describe the data connections. > > Otherwise it would get more complicated for display controller drivers to > > use different types of bridges. > > It was discussed already, and DT guideline is to skip graphs in simple > case of parent/child nodes, see for example [1]. > > [1]: https://marc.info/?l=dri-devel&m=148354108702517&w=2 That's when the child as no other connection at all. I don't think it makes sense to mix description of connections through parent/child relationships and through ports for a single device. And that being said, I don't agree with Rob's comment there. Having two different methods to describe connections means that you have to implement them both in all display controller drivers (and even all bridge drivers in the case of chained bridges). That's an extra complexity that can easily be avoided by standardizing DT bindings. I also wonder whether Rob's position hasn't been reconsidered since then; I vaguely recalled another more recent discussion on this topic. I'm a bit too busy now to try and dig it up now I'm afraid :-/ > >>>> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt > >>>> + > >>>> +Example: > >>>> + > >>>> + bridge@0 { > >>>> + reg = <0>; > >>>> + compatible = "toshiba,tc358764"; > >>>> + vddc-supply = <&vcc_1v2_reg>; > >>>> + vddio-supply = <&vcc_1v8_reg>; > >>>> + vddmipi-supply = <&vcc_1v2_reg>; > >>>> + vddlvds133-supply = <&vcc_3v3_reg>; > >>>> + vddlvds112-supply = <&vcc_1v2_reg>; > >>>> + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; > >>>> + #address-cells = <1>; > >>>> + #size-cells = <0>; > >>>> + port@1 { > >>>> + reg = <1>; > >>>> + lvds_ep: endpoint { > >>>> + remote-endpoint = <&panel_ep>; > >>>> + }; > >>>> + }; > >>>> + };
diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt new file mode 100644 index 0000000..d09bdc2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt @@ -0,0 +1,42 @@ +TC358764 MIPI-DSI to LVDS panel bridge + +Required properties: + - compatible: "toshiba,tc358764" + - reg: the virtual channel number of a DSI peripheral + - vddc-supply: core voltage supply + - vddio-supply: I/O voltage supply + - vddmipi-supply: MIPI voltage supply + - vddlvds133-supply: LVDS1 3.3V voltage supply + - vddlvds112-supply: LVDS1 1.2V voltage supply + - reset-gpios: a GPIO spec for the reset pin + +The device node can contain zero to two 'port' child nodes, each with one +child +'endpoint' node, according to the bindings defined in [1]. +The following are properties specific to those nodes. + +port: + - reg: (required) can be 0 for DSI port or 1 for LVDS port; + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + bridge@0 { + reg = <0>; + compatible = "toshiba,tc358764"; + vddc-supply = <&vcc_1v2_reg>; + vddio-supply = <&vcc_1v8_reg>; + vddmipi-supply = <&vcc_1v2_reg>; + vddlvds133-supply = <&vcc_3v3_reg>; + vddlvds112-supply = <&vcc_1v2_reg>; + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + port@1 { + reg = <1>; + lvds_ep: endpoint { + remote-endpoint = <&panel_ep>; + }; + }; + };