new file mode 100644
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4412 based Galaxy S3 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4412-midas.dtsi"
+
+/ {
+ aliases {
+ i2c9 = &i2c_ak8975;
+ i2c10 = &i2c_cm36651;
+ };
+
+ regulators {
+ lcd_vdd3_reg: voltage-regulator-2 {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD_VDD_2.2V";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ ps_als_reg: voltage-regulator-5 {
+ compatible = "regulator-fixed";
+ regulator-name = "LED_A_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ i2c_ak8975: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&gpy2 4 GPIO_ACTIVE_HIGH>, <&gpy2 5 GPIO_ACTIVE_HIGH>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ak8975@c {
+ compatible = "asahi-kasei,ak8975";
+ reg = <0x0c>;
+ gpios = <&gpj0 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ i2c_cm36651: i2c-gpio-2 {
+ compatible = "i2c-gpio";
+ gpios = <&gpf0 0 GPIO_ACTIVE_LOW>, <&gpf0 1 GPIO_ACTIVE_LOW>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cm36651@18 {
+ compatible = "capella,cm36651";
+ reg = <0x18>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ vled-supply = <&ps_als_reg>;
+ };
+ };
+};
+
+&buck9_reg {
+ maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+};
+
+&cam_af_reg {
+ gpio = <&gpm0 4 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&cam_io_reg {
+ gpio = <&gpm0 2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&dsi_0 {
+ status = "okay";
+
+ panel@0 {
+ compatible = "samsung,s6e8aa0";
+ reg = <0>;
+ vdd3-supply = <&lcd_vdd3_reg>;
+ vci-supply = <&ldo25_reg>;
+ reset-gpios = <&gpf2 1 GPIO_ACTIVE_HIGH>;
+ power-on-delay= <50>;
+ reset-delay = <100>;
+ init-delay = <100>;
+ flip-horizontal;
+ flip-vertical;
+ panel-width-mm = <58>;
+ panel-height-mm = <103>;
+
+ display-timings {
+ timing-0 {
+ clock-frequency = <57153600>;
+ hactive = <720>;
+ vactive = <1280>;
+ hfront-porch = <5>;
+ hback-porch = <5>;
+ hsync-len = <5>;
+ vfront-porch = <13>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+ };
+};
+
+&i2c_3 {
+ mms114-touchscreen@48 {
+ compatible = "melfas,mms114";
+ reg = <0x48>;
+ interrupt-parent = <&gpm2>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ x-size = <720>;
+ y-size = <1280>;
+ avdd-supply = <&ldo23_reg>;
+ vdd-supply = <&ldo24_reg>;
+ };
+};
+
+&ldo25_reg {
+ regulator-name = "LCD_VCC_3.3V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
+
+&s5c73m3 {
+ standby-gpios = <&gpm0 1 GPIO_ACTIVE_LOW>; /* ISP_STANDBY */
+ vdda-supply = <&ldo17_reg>;
+ status = "okay";
+};
similarity index 91%
copy from arch/arm/boot/dts/exynos4412-trats2.dts
copy to arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -10,7 +10,7 @@
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
-*/
+ */
/dts-v1/;
#include "exynos4412.dtsi"
@@ -21,23 +21,14 @@
#include <dt-bindings/pinctrl/samsung.h>
/ {
- model = "Samsung Trats 2 based on Exynos4412";
- compatible = "samsung,trats2", "samsung,exynos4412", "samsung,exynos4";
+ compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
aliases {
- i2c9 = &i2c_ak8975;
- i2c10 = &i2c_cm36651;
i2c11 = &i2c_max77693;
i2c12 = &i2c_max77693_fuel;
};
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x40000000>;
- };
-
chosen {
- bootargs = "console=ttySAC2,115200N8 root=/dev/mmcblk0p5 rootwait earlyprintk panic=5";
stdout-path = &serial_2;
};
@@ -68,17 +59,8 @@
regulator-name = "CAM_SENSOR_A";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpm0 2 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- lcd_vdd3_reg: voltage-regulator-2 {
- compatible = "regulator-fixed";
- regulator-name = "LCD_VDD_2.2V";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
+ status = "disabled";
};
cam_af_reg: voltage-regulator-3 {
@@ -86,17 +68,8 @@
regulator-name = "CAM_AF";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpm0 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- ps_als_reg: voltage-regulator-5 {
- compatible = "regulator-fixed";
- regulator-name = "LED_A_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>;
enable-active-high;
+ status = "disabled";
};
vsil12: voltage-regulator-6 {
@@ -227,37 +200,6 @@
};
};
- i2c_ak8975: i2c-gpio-0 {
- compatible = "i2c-gpio";
- gpios = <&gpy2 4 GPIO_ACTIVE_HIGH>, <&gpy2 5 GPIO_ACTIVE_HIGH>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- ak8975@c {
- compatible = "asahi-kasei,ak8975";
- reg = <0x0c>;
- gpios = <&gpj0 7 GPIO_ACTIVE_HIGH>;
- };
- };
-
- i2c_cm36651: i2c-gpio-2 {
- compatible = "i2c-gpio";
- gpios = <&gpf0 0 GPIO_ACTIVE_LOW>, <&gpf0 1 GPIO_ACTIVE_LOW>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- cm36651@18 {
- compatible = "capella,cm36651";
- reg = <0x18>;
- interrupt-parent = <&gpx0>;
- interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
- vled-supply = <&ps_als_reg>;
- };
- };
-
i2c-mhl {
compatible = "i2c-gpio";
gpios = <&gpf0 4 GPIO_ACTIVE_HIGH>, <&gpf0 6 GPIO_ACTIVE_HIGH>;
@@ -296,8 +238,6 @@
<&clock CLK_MOUT_CAM1>;
assigned-clock-parents = <&clock CLK_XUSBXTI>,
<&clock CLK_XUSBXTI>;
-
-
};
wlan_pwrseq: sdhci3-pwrseq {
@@ -454,36 +394,6 @@
samsung,burst-clock-frequency = <500000000>;
samsung,esc-clock-frequency = <20000000>;
samsung,pll-clock-frequency = <24000000>;
- status = "okay";
-
- panel@0 {
- compatible = "samsung,s6e8aa0";
- reg = <0>;
- vdd3-supply = <&lcd_vdd3_reg>;
- vci-supply = <&ldo25_reg>;
- reset-gpios = <&gpf2 1 GPIO_ACTIVE_HIGH>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- flip-horizontal;
- flip-vertical;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
-
- display-timings {
- timing-0 {
- clock-frequency = <57153600>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
- };
};
&exynos_usbphy {
@@ -605,14 +515,12 @@
pinctrl-names = "default";
status = "okay";
- s5c73m3@3c {
+ s5c73m3: s5c73m3@3c {
compatible = "samsung,s5c73m3";
reg = <0x3c>;
- standby-gpios = <&gpm0 1 GPIO_ACTIVE_LOW>; /* ISP_STANDBY */
xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */
vdd-int-supply = <&buck9_reg>;
vddio-cis-supply = <&ldo9_reg>;
- vdda-supply = <&ldo17_reg>;
vddio-host-supply = <&ldo18_reg>;
vdd-af-supply = <&cam_af_reg>;
vdd-reg-supply = <&cam_io_reg>;
@@ -620,6 +528,7 @@
/* CAM_A_CLKOUT */
clocks = <&camera 0>;
clock-names = "cis_extclk";
+ status = "disabled";
port {
s5c73m3_ep: endpoint {
remote-endpoint = <&csis0_ep>;
@@ -636,17 +545,6 @@
pinctrl-0 = <&i2c3_bus>;
pinctrl-names = "default";
status = "okay";
-
- mms114-touchscreen@48 {
- compatible = "melfas,mms114";
- reg = <0x48>;
- interrupt-parent = <&gpm2>;
- interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
- x-size = <720>;
- y-size = <1280>;
- avdd-supply = <&ldo23_reg>;
- vdd-supply = <&ldo24_reg>;
- };
};
&i2c_4 {
@@ -874,9 +772,7 @@
};
ldo25_reg: LDO25 {
- regulator-name = "LCD_VCC_3.3V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
+ regulator-name = "LDO25";
};
ldo26_reg: LDO26 {
@@ -960,7 +856,6 @@
regulator-name = "CAM_ISP_CORE_1.2V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1200000>;
- maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
};
};
};
dissimilarity index 98%
@@ -1,1415 +1,26 @@
-/*
- * Samsung's Exynos4412 based Trats 2 board device tree source
- *
- * Copyright (c) 2013 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Device tree source file for Samsung's Trats 2 board which is based on
- * Samsung's Exynos4412 SoC.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/dts-v1/;
-#include "exynos4412.dtsi"
-#include "exynos4412-ppmu-common.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clock/maxim,max77686.h>
-#include <dt-bindings/pinctrl/samsung.h>
-
-/ {
- model = "Samsung Trats 2 based on Exynos4412";
- compatible = "samsung,trats2", "samsung,exynos4412", "samsung,exynos4";
-
- aliases {
- i2c9 = &i2c_ak8975;
- i2c10 = &i2c_cm36651;
- i2c11 = &i2c_max77693;
- i2c12 = &i2c_max77693_fuel;
- };
-
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x40000000>;
- };
-
- chosen {
- bootargs = "console=ttySAC2,115200N8 root=/dev/mmcblk0p5 rootwait earlyprintk panic=5";
- stdout-path = &serial_2;
- };
-
- firmware@204f000 {
- compatible = "samsung,secure-firmware";
- reg = <0x0204F000 0x1000>;
- };
-
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti", "fixed-clock";
- clock-frequency = <0>;
- };
-
- xusbxti {
- compatible = "samsung,clock-xusbxti", "fixed-clock";
- clock-frequency = <24000000>;
- };
- };
-
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- cam_io_reg: voltage-regulator-1 {
- compatible = "regulator-fixed";
- regulator-name = "CAM_SENSOR_A";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- gpio = <&gpm0 2 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- lcd_vdd3_reg: voltage-regulator-2 {
- compatible = "regulator-fixed";
- regulator-name = "LCD_VDD_2.2V";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- cam_af_reg: voltage-regulator-3 {
- compatible = "regulator-fixed";
- regulator-name = "CAM_AF";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- gpio = <&gpm0 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- ps_als_reg: voltage-regulator-5 {
- compatible = "regulator-fixed";
- regulator-name = "LED_A_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vsil12: voltage-regulator-6 {
- compatible = "regulator-fixed";
- regulator-name = "VSIL_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&buck7_reg>;
- };
-
- vcc33mhl: voltage-regulator-7 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_3.3_MHL";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vcc18mhl: voltage-regulator-8 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_1.8_MHL";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- key-down {
- gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
- linux,code = <114>;
- label = "volume down";
- debounce-interval = <10>;
- };
-
- key-up {
- gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
- linux,code = <115>;
- label = "volume up";
- debounce-interval = <10>;
- };
-
- key-power {
- gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
- linux,code = <116>;
- label = "power";
- debounce-interval = <10>;
- wakeup-source;
- };
-
- key-ok {
- gpios = <&gpx0 1 GPIO_ACTIVE_LOW>;
- linux,code = <139>;
- label = "ok";
- debounce-inteval = <10>;
- wakeup-source;
- };
- };
-
- i2c_max77693: i2c-gpio-1 {
- compatible = "i2c-gpio";
- gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- max77693@66 {
- compatible = "maxim,max77693";
- interrupt-parent = <&gpx1>;
- interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
- reg = <0x66>;
-
- regulators {
- esafeout1_reg: ESAFEOUT1 {
- regulator-name = "ESAFEOUT1";
- };
- esafeout2_reg: ESAFEOUT2 {
- regulator-name = "ESAFEOUT2";
- };
- charger_reg: CHARGER {
- regulator-name = "CHARGER";
- regulator-min-microamp = <60000>;
- regulator-max-microamp = <2580000>;
- };
- };
-
- max77693_haptic {
- compatible = "maxim,max77693-haptic";
- haptic-supply = <&ldo26_reg>;
- pwms = <&pwm 0 38022 0>;
- };
-
- charger {
- compatible = "maxim,max77693-charger";
-
- maxim,constant-microvolt = <4350000>;
- maxim,min-system-microvolt = <3600000>;
- maxim,thermal-regulation-celsius = <100>;
- maxim,battery-overcurrent-microamp = <3500000>;
- maxim,charge-input-threshold-microvolt = <4300000>;
- };
- };
- };
-
- i2c_max77693_fuel: i2c-gpio-3 {
- compatible = "i2c-gpio";
- gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>, <&gpf1 4 GPIO_ACTIVE_HIGH>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- max77693-fuel-gauge@36 {
- compatible = "maxim,max17047";
- interrupt-parent = <&gpx2>;
- interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
- reg = <0x36>;
-
- maxim,over-heat-temp = <700>;
- maxim,over-volt = <4500>;
- };
- };
-
- i2c_ak8975: i2c-gpio-0 {
- compatible = "i2c-gpio";
- gpios = <&gpy2 4 GPIO_ACTIVE_HIGH>, <&gpy2 5 GPIO_ACTIVE_HIGH>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- ak8975@c {
- compatible = "asahi-kasei,ak8975";
- reg = <0x0c>;
- gpios = <&gpj0 7 GPIO_ACTIVE_HIGH>;
- };
- };
-
- i2c_cm36651: i2c-gpio-2 {
- compatible = "i2c-gpio";
- gpios = <&gpf0 0 GPIO_ACTIVE_LOW>, <&gpf0 1 GPIO_ACTIVE_LOW>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- cm36651@18 {
- compatible = "capella,cm36651";
- reg = <0x18>;
- interrupt-parent = <&gpx0>;
- interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
- vled-supply = <&ps_als_reg>;
- };
- };
-
- i2c-mhl {
- compatible = "i2c-gpio";
- gpios = <&gpf0 4 GPIO_ACTIVE_HIGH>, <&gpf0 6 GPIO_ACTIVE_HIGH>;
- i2c-gpio,delay-us = <100>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pinctrl-0 = <&i2c_mhl_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- sii9234: hdmi-bridge@39 {
- compatible = "sil,sii9234";
- avcc33-supply = <&vcc33mhl>;
- iovcc18-supply = <&vcc18mhl>;
- avcc12-supply = <&vsil12>;
- cvcc12-supply = <&vsil12>;
- reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>;
- interrupt-parent = <&gpf3>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x39>;
-
- port {
- mhl_to_hdmi: endpoint {
- remote-endpoint = <&hdmi_to_mhl>;
- };
- };
- };
- };
-
- camera: camera {
- pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
- pinctrl-names = "default";
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_CAM0>,
- <&clock CLK_MOUT_CAM1>;
- assigned-clock-parents = <&clock CLK_XUSBXTI>,
- <&clock CLK_XUSBXTI>;
-
-
- };
-
- wlan_pwrseq: sdhci3-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpj0 0 GPIO_ACTIVE_LOW>;
- clocks = <&max77686 MAX77686_CLK_PMIC>;
- clock-names = "ext_clock";
- };
-
- sound {
- compatible = "samsung,trats2-audio";
- samsung,i2s-controller = <&i2s0>;
- samsung,model = "Trats2";
- samsung,audio-codec = <&wm1811>;
- samsung,audio-routing =
- "SPK", "SPKOUTLN",
- "SPK", "SPKOUTLP",
- "SPK", "SPKOUTRN",
- "SPK", "SPKOUTRP";
- };
-
- thermistor-ap {
- compatible = "murata,ncp15wb473";
- pullup-uv = <1800000>; /* VCC_1.8V_AP */
- pullup-ohm = <100000>; /* 100K */
- pulldown-ohm = <100000>; /* 100K */
- io-channels = <&adc 1>; /* AP temperature */
- };
-
- thermistor-battery {
- compatible = "murata,ncp15wb473";
- pullup-uv = <1800000>; /* VCC_1.8V_AP */
- pullup-ohm = <100000>; /* 100K */
- pulldown-ohm = <100000>; /* 100K */
- io-channels = <&adc 2>; /* Battery temperature */
- };
-
- thermal-zones {
- cpu_thermal: cpu-thermal {
- cooling-maps {
- map0 {
- /* Corresponds to 800MHz at freq_table */
- cooling-device = <&cpu0 7 7>;
- };
- map1 {
- /* Corresponds to 200MHz at freq_table */
- cooling-device = <&cpu0 13 13>;
- };
- };
- };
- };
-};
-
-&adc {
- vdd-supply = <&ldo3_reg>;
- status = "okay";
-};
-
-&bus_dmc {
- devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
- vdd-supply = <&buck1_reg>;
- status = "okay";
-};
-
-&bus_acp {
- devfreq = <&bus_dmc>;
- status = "okay";
-};
-
-&bus_c2c {
- devfreq = <&bus_dmc>;
- status = "okay";
-};
-
-&bus_leftbus {
- devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
- vdd-supply = <&buck3_reg>;
- status = "okay";
-};
-
-&bus_rightbus {
- devfreq = <&bus_leftbus>;
- status = "okay";
-};
-
-&bus_display {
- devfreq = <&bus_leftbus>;
- status = "okay";
-};
-
-&bus_fsys {
- devfreq = <&bus_leftbus>;
- status = "okay";
-};
-
-&bus_peri {
- devfreq = <&bus_leftbus>;
- status = "okay";
-};
-
-&bus_mfc {
- devfreq = <&bus_leftbus>;
- status = "okay";
-};
-
-&cpu0 {
- cpu0-supply = <&buck2_reg>;
-};
-
-&csis_0 {
- status = "okay";
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- assigned-clocks = <&clock CLK_MOUT_CSIS0>,
- <&clock CLK_SCLK_CSIS0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-
- /* Camera C (3) MIPI CSI-2 (CSIS0) */
- port@3 {
- reg = <3>;
- csis0_ep: endpoint {
- remote-endpoint = <&s5c73m3_ep>;
- data-lanes = <1 2 3 4>;
- samsung,csis-hs-settle = <12>;
- };
- };
-};
-
-&csis_1 {
- status = "okay";
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- assigned-clocks = <&clock CLK_MOUT_CSIS1>,
- <&clock CLK_SCLK_CSIS1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-
- /* Camera D (4) MIPI CSI-2 (CSIS1) */
- port@4 {
- reg = <4>;
- csis1_ep: endpoint {
- remote-endpoint = <&is_s5k6a3_ep>;
- data-lanes = <1>;
- samsung,csis-hs-settle = <18>;
- samsung,csis-wclk;
- };
- };
-};
-
-&dsi_0 {
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- samsung,burst-clock-frequency = <500000000>;
- samsung,esc-clock-frequency = <20000000>;
- samsung,pll-clock-frequency = <24000000>;
- status = "okay";
-
- panel@0 {
- compatible = "samsung,s6e8aa0";
- reg = <0>;
- vdd3-supply = <&lcd_vdd3_reg>;
- vci-supply = <&ldo25_reg>;
- reset-gpios = <&gpf2 1 GPIO_ACTIVE_HIGH>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- flip-horizontal;
- flip-vertical;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
-
- display-timings {
- timing-0 {
- clock-frequency = <57153600>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
- };
-};
-
-&exynos_usbphy {
- vbus-supply = <&esafeout1_reg>;
- status = "okay";
-};
-
-&fimc_0 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC0>,
- <&clock CLK_SCLK_FIMC0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-};
-
-&fimc_1 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC1>,
- <&clock CLK_SCLK_FIMC1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-};
-
-&fimc_2 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC2>,
- <&clock CLK_SCLK_FIMC2>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-};
-
-&fimc_3 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC3>,
- <&clock CLK_SCLK_FIMC3>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-};
-
-&fimc_is {
- pinctrl-0 = <&fimc_is_uart>;
- pinctrl-names = "default";
- status = "okay";
-
- i2c1_isp: i2c-isp@12140000 {
- pinctrl-0 = <&fimc_is_i2c1>;
- pinctrl-names = "default";
-
- s5k6a3@10 {
- compatible = "samsung,s5k6a3";
- reg = <0x10>;
- svdda-supply = <&cam_io_reg>;
- svddio-supply = <&ldo19_reg>;
- afvdd-supply = <&ldo19_reg>;
- clock-frequency = <24000000>;
- /* CAM_B_CLKOUT */
- clocks = <&camera 1>;
- clock-names = "extclk";
- samsung,camclk-out = <1>;
- gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>;
-
- port {
- is_s5k6a3_ep: endpoint {
- remote-endpoint = <&csis1_ep>;
- data-lanes = <1>;
- };
- };
- };
- };
-};
-
-&fimc_lite_0 {
- status = "okay";
-};
-
-&fimc_lite_1 {
- status = "okay";
-};
-
-&fimd {
- status = "okay";
-};
-
-&hdmi {
- hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd>;
- vdd-supply = <&ldo3_reg>;
- vdd_osc-supply = <&ldo4_reg>;
- vdd_pll-supply = <&ldo3_reg>;
- ddc = <&i2c_5>;
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@1 {
- reg = <1>;
- hdmi_to_mhl: endpoint {
- remote-endpoint = <&mhl_to_hdmi>;
- };
- };
- };
-};
-
-&hsotg {
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
- dr_mode = "peripheral";
- status = "okay";
-};
-
-&i2c_0 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- s5c73m3@3c {
- compatible = "samsung,s5c73m3";
- reg = <0x3c>;
- standby-gpios = <&gpm0 1 GPIO_ACTIVE_LOW>; /* ISP_STANDBY */
- xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */
- vdd-int-supply = <&buck9_reg>;
- vddio-cis-supply = <&ldo9_reg>;
- vdda-supply = <&ldo17_reg>;
- vddio-host-supply = <&ldo18_reg>;
- vdd-af-supply = <&cam_af_reg>;
- vdd-reg-supply = <&cam_io_reg>;
- clock-frequency = <24000000>;
- /* CAM_A_CLKOUT */
- clocks = <&camera 0>;
- clock-names = "cis_extclk";
- port {
- s5c73m3_ep: endpoint {
- remote-endpoint = <&csis0_ep>;
- data-lanes = <1 2 3 4>;
- };
- };
- };
-};
-
-&i2c_3 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- mms114-touchscreen@48 {
- compatible = "melfas,mms114";
- reg = <0x48>;
- interrupt-parent = <&gpm2>;
- interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
- x-size = <720>;
- y-size = <1280>;
- avdd-supply = <&ldo23_reg>;
- vdd-supply = <&ldo24_reg>;
- };
-};
-
-&i2c_4 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c4_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- wm1811: wm1811@1a {
- compatible = "wlf,wm1811";
- reg = <0x1a>;
- clocks = <&pmu_system_controller 0>;
- clock-names = "MCLK1";
- DCVDD-supply = <&ldo3_reg>;
- DBVDD1-supply = <&ldo3_reg>;
- wlf,ldo1ena = <&gpj0 4 0>;
- };
-};
-
-&i2c_5 {
- status = "okay";
-};
-
-&i2c_7 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c7_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- max77686: max77686_pmic@9 {
- compatible = "maxim,max77686";
- interrupt-parent = <&gpx0>;
- interrupts = <7 IRQ_TYPE_NONE>;
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VALIVE_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VM1M2_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "VCC_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "VCC_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "VCC_1.8V_IO";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "VMPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "VPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "VMIPI_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "CAM_ISP_MIPI_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "VABB1_1.95V";
- regulator-min-microvolt = <1950000>;
- regulator-max-microvolt = <1950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "VUOTG_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "NFC_AVDD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo14_reg: LDO14 {
- regulator-name = "VABB2_1.95V";
- regulator-min-microvolt = <1950000>;
- regulator-max-microvolt = <1950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "VHSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "VHSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "CAM_SENSOR_CORE_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo18_reg: LDO18 {
- regulator-name = "CAM_ISP_SEN_IO_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo20_reg: LDO20 {
- regulator-name = "VDDQ_PRE_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "VTF_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
- };
-
- ldo22_reg: LDO22 {
- regulator-name = "VMEM_VDD_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
- };
-
- ldo23_reg: LDO23 {
- regulator-name = "TSP_AVDD_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "TSP_VDD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo25_reg: LDO25 {
- regulator-name = "LCD_VCC_3.3V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo26_reg: LDO26 {
- regulator-name = "MOTOR_VCC_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "VMEM_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "VCC_SUB_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "VCC_SUB_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "VMEM_VDDF_3.0V";
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "CAM_ISP_CORE_1.2V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1200000>;
- maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
- };
- };
- };
-};
-
-&i2c_8 {
- status = "okay";
-};
-
-&i2s0 {
- pinctrl-0 = <&i2s0_bus>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&mixer {
- status = "okay";
-};
-
-&mshc_0 {
- broken-cd;
- non-removable;
- card-detect-delay = <200>;
- vmmc-supply = <&ldo22_reg>;
- clock-frequency = <400000000>;
- samsung,dw-mshc-ciu-div = <0>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- status = "okay";
- bus-width = <8>;
- cap-mmc-highspeed;
-};
-
-&pmu_system_controller {
- assigned-clocks = <&pmu_system_controller 0>;
- assigned-clock-parents = <&clock CLK_XUSBXTI>;
-};
-
-&pinctrl_0 {
- pinctrl-names = "default";
- pinctrl-0 = <&sleep0>;
-
- mhl_int: mhl-int {
- samsung,pins = "gpf3-5";
- samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
- };
-
- i2c_mhl_bus: i2c-mhl-bus {
- samsung,pins = "gpf0-4", "gpf0-6";
- samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
- samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
- samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
- };
-
- sleep0: sleep-states {
- PIN_SLP(gpa0-0, INPUT, NONE);
- PIN_SLP(gpa0-1, OUT0, NONE);
- PIN_SLP(gpa0-2, INPUT, NONE);
- PIN_SLP(gpa0-3, INPUT, UP);
- PIN_SLP(gpa0-4, INPUT, NONE);
- PIN_SLP(gpa0-5, INPUT, DOWN);
- PIN_SLP(gpa0-6, INPUT, DOWN);
- PIN_SLP(gpa0-7, INPUT, UP);
-
- PIN_SLP(gpa1-0, INPUT, DOWN);
- PIN_SLP(gpa1-1, INPUT, DOWN);
- PIN_SLP(gpa1-2, INPUT, DOWN);
- PIN_SLP(gpa1-3, INPUT, DOWN);
- PIN_SLP(gpa1-4, INPUT, DOWN);
- PIN_SLP(gpa1-5, INPUT, DOWN);
-
- PIN_SLP(gpb-0, INPUT, NONE);
- PIN_SLP(gpb-1, INPUT, NONE);
- PIN_SLP(gpb-2, INPUT, NONE);
- PIN_SLP(gpb-3, INPUT, NONE);
- PIN_SLP(gpb-4, INPUT, DOWN);
- PIN_SLP(gpb-5, INPUT, UP);
- PIN_SLP(gpb-6, INPUT, DOWN);
- PIN_SLP(gpb-7, INPUT, DOWN);
-
- PIN_SLP(gpc0-0, INPUT, DOWN);
- PIN_SLP(gpc0-1, INPUT, DOWN);
- PIN_SLP(gpc0-2, INPUT, DOWN);
- PIN_SLP(gpc0-3, INPUT, DOWN);
- PIN_SLP(gpc0-4, INPUT, DOWN);
-
- PIN_SLP(gpc1-0, INPUT, NONE);
- PIN_SLP(gpc1-1, PREV, NONE);
- PIN_SLP(gpc1-2, INPUT, NONE);
- PIN_SLP(gpc1-3, INPUT, NONE);
- PIN_SLP(gpc1-4, INPUT, NONE);
-
- PIN_SLP(gpd0-0, INPUT, DOWN);
- PIN_SLP(gpd0-1, INPUT, DOWN);
- PIN_SLP(gpd0-2, INPUT, NONE);
- PIN_SLP(gpd0-3, INPUT, NONE);
-
- PIN_SLP(gpd1-0, INPUT, DOWN);
- PIN_SLP(gpd1-1, INPUT, DOWN);
- PIN_SLP(gpd1-2, INPUT, NONE);
- PIN_SLP(gpd1-3, INPUT, NONE);
-
- PIN_SLP(gpf0-0, INPUT, NONE);
- PIN_SLP(gpf0-1, INPUT, NONE);
- PIN_SLP(gpf0-2, INPUT, DOWN);
- PIN_SLP(gpf0-3, INPUT, DOWN);
- PIN_SLP(gpf0-4, INPUT, NONE);
- PIN_SLP(gpf0-5, INPUT, DOWN);
- PIN_SLP(gpf0-6, INPUT, NONE);
- PIN_SLP(gpf0-7, INPUT, DOWN);
-
- PIN_SLP(gpf1-0, INPUT, DOWN);
- PIN_SLP(gpf1-1, INPUT, DOWN);
- PIN_SLP(gpf1-2, INPUT, DOWN);
- PIN_SLP(gpf1-3, INPUT, DOWN);
- PIN_SLP(gpf1-4, INPUT, NONE);
- PIN_SLP(gpf1-5, INPUT, NONE);
- PIN_SLP(gpf1-6, INPUT, DOWN);
- PIN_SLP(gpf1-7, PREV, NONE);
-
- PIN_SLP(gpf2-0, PREV, NONE);
- PIN_SLP(gpf2-1, INPUT, DOWN);
- PIN_SLP(gpf2-2, INPUT, DOWN);
- PIN_SLP(gpf2-3, INPUT, DOWN);
- PIN_SLP(gpf2-4, INPUT, DOWN);
- PIN_SLP(gpf2-5, INPUT, DOWN);
- PIN_SLP(gpf2-6, INPUT, NONE);
- PIN_SLP(gpf2-7, INPUT, NONE);
-
- PIN_SLP(gpf3-0, INPUT, NONE);
- PIN_SLP(gpf3-1, PREV, NONE);
- PIN_SLP(gpf3-2, PREV, NONE);
- PIN_SLP(gpf3-3, PREV, NONE);
- PIN_SLP(gpf3-4, OUT1, NONE);
- PIN_SLP(gpf3-5, INPUT, DOWN);
-
- PIN_SLP(gpj0-0, PREV, NONE);
- PIN_SLP(gpj0-1, PREV, NONE);
- PIN_SLP(gpj0-2, PREV, NONE);
- PIN_SLP(gpj0-3, INPUT, DOWN);
- PIN_SLP(gpj0-4, PREV, NONE);
- PIN_SLP(gpj0-5, PREV, NONE);
- PIN_SLP(gpj0-6, INPUT, DOWN);
- PIN_SLP(gpj0-7, INPUT, DOWN);
-
- PIN_SLP(gpj1-0, INPUT, DOWN);
- PIN_SLP(gpj1-1, PREV, NONE);
- PIN_SLP(gpj1-2, PREV, NONE);
- PIN_SLP(gpj1-3, INPUT, DOWN);
- PIN_SLP(gpj1-4, INPUT, DOWN);
- };
-};
-
-&pinctrl_1 {
- pinctrl-names = "default";
- pinctrl-0 = <&sleep1>;
-
- hdmi_hpd: hdmi-hpd {
- samsung,pins = "gpx3-7";
- samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
- };
-
- sleep1: sleep-states {
- PIN_SLP(gpk0-0, PREV, NONE);
- PIN_SLP(gpk0-1, PREV, NONE);
- PIN_SLP(gpk0-2, OUT0, NONE);
- PIN_SLP(gpk0-3, PREV, NONE);
- PIN_SLP(gpk0-4, PREV, NONE);
- PIN_SLP(gpk0-5, PREV, NONE);
- PIN_SLP(gpk0-6, PREV, NONE);
-
- PIN_SLP(gpk1-0, INPUT, DOWN);
- PIN_SLP(gpk1-1, INPUT, DOWN);
- PIN_SLP(gpk1-2, INPUT, DOWN);
- PIN_SLP(gpk1-3, PREV, NONE);
- PIN_SLP(gpk1-4, PREV, NONE);
- PIN_SLP(gpk1-5, PREV, NONE);
- PIN_SLP(gpk1-6, PREV, NONE);
-
- PIN_SLP(gpk2-0, INPUT, DOWN);
- PIN_SLP(gpk2-1, INPUT, DOWN);
- PIN_SLP(gpk2-2, INPUT, DOWN);
- PIN_SLP(gpk2-3, INPUT, DOWN);
- PIN_SLP(gpk2-4, INPUT, DOWN);
- PIN_SLP(gpk2-5, INPUT, DOWN);
- PIN_SLP(gpk2-6, INPUT, DOWN);
-
- PIN_SLP(gpk3-0, OUT0, NONE);
- PIN_SLP(gpk3-1, INPUT, NONE);
- PIN_SLP(gpk3-2, INPUT, DOWN);
- PIN_SLP(gpk3-3, INPUT, NONE);
- PIN_SLP(gpk3-4, INPUT, NONE);
- PIN_SLP(gpk3-5, INPUT, NONE);
- PIN_SLP(gpk3-6, INPUT, NONE);
-
- PIN_SLP(gpl0-0, INPUT, DOWN);
- PIN_SLP(gpl0-1, INPUT, DOWN);
- PIN_SLP(gpl0-2, INPUT, DOWN);
- PIN_SLP(gpl0-3, INPUT, DOWN);
- PIN_SLP(gpl0-4, PREV, NONE);
- PIN_SLP(gpl0-6, PREV, NONE);
-
- PIN_SLP(gpl1-0, INPUT, DOWN);
- PIN_SLP(gpl1-1, INPUT, DOWN);
- PIN_SLP(gpl2-0, INPUT, DOWN);
- PIN_SLP(gpl2-1, INPUT, DOWN);
- PIN_SLP(gpl2-2, INPUT, DOWN);
- PIN_SLP(gpl2-3, INPUT, DOWN);
- PIN_SLP(gpl2-4, INPUT, DOWN);
- PIN_SLP(gpl2-5, INPUT, DOWN);
- PIN_SLP(gpl2-6, PREV, NONE);
- PIN_SLP(gpl2-7, INPUT, DOWN);
-
- PIN_SLP(gpm0-0, INPUT, DOWN);
- PIN_SLP(gpm0-1, INPUT, DOWN);
- PIN_SLP(gpm0-2, INPUT, DOWN);
- PIN_SLP(gpm0-3, INPUT, DOWN);
- PIN_SLP(gpm0-4, INPUT, DOWN);
- PIN_SLP(gpm0-5, INPUT, DOWN);
- PIN_SLP(gpm0-6, INPUT, DOWN);
- PIN_SLP(gpm0-7, INPUT, DOWN);
-
- PIN_SLP(gpm1-0, INPUT, DOWN);
- PIN_SLP(gpm1-1, INPUT, DOWN);
- PIN_SLP(gpm1-2, INPUT, NONE);
- PIN_SLP(gpm1-3, INPUT, NONE);
- PIN_SLP(gpm1-4, INPUT, NONE);
- PIN_SLP(gpm1-5, INPUT, NONE);
- PIN_SLP(gpm1-6, INPUT, DOWN);
-
- PIN_SLP(gpm2-0, INPUT, NONE);
- PIN_SLP(gpm2-1, INPUT, NONE);
- PIN_SLP(gpm2-2, INPUT, DOWN);
- PIN_SLP(gpm2-3, INPUT, DOWN);
- PIN_SLP(gpm2-4, INPUT, DOWN);
-
- PIN_SLP(gpm3-0, PREV, NONE);
- PIN_SLP(gpm3-1, PREV, NONE);
- PIN_SLP(gpm3-2, PREV, NONE);
- PIN_SLP(gpm3-3, OUT1, NONE);
- PIN_SLP(gpm3-4, INPUT, DOWN);
- PIN_SLP(gpm3-5, INPUT, DOWN);
- PIN_SLP(gpm3-6, INPUT, DOWN);
- PIN_SLP(gpm3-7, INPUT, DOWN);
-
- PIN_SLP(gpm4-0, INPUT, DOWN);
- PIN_SLP(gpm4-1, INPUT, DOWN);
- PIN_SLP(gpm4-2, INPUT, DOWN);
- PIN_SLP(gpm4-3, INPUT, DOWN);
- PIN_SLP(gpm4-4, INPUT, DOWN);
- PIN_SLP(gpm4-5, INPUT, DOWN);
- PIN_SLP(gpm4-6, INPUT, DOWN);
- PIN_SLP(gpm4-7, INPUT, DOWN);
-
- PIN_SLP(gpy0-0, INPUT, DOWN);
- PIN_SLP(gpy0-1, INPUT, DOWN);
- PIN_SLP(gpy0-2, INPUT, DOWN);
- PIN_SLP(gpy0-3, INPUT, DOWN);
- PIN_SLP(gpy0-4, INPUT, DOWN);
- PIN_SLP(gpy0-5, INPUT, DOWN);
-
- PIN_SLP(gpy1-0, INPUT, DOWN);
- PIN_SLP(gpy1-1, INPUT, DOWN);
- PIN_SLP(gpy1-2, INPUT, DOWN);
- PIN_SLP(gpy1-3, INPUT, DOWN);
-
- PIN_SLP(gpy2-0, PREV, NONE);
- PIN_SLP(gpy2-1, INPUT, DOWN);
- PIN_SLP(gpy2-2, INPUT, NONE);
- PIN_SLP(gpy2-3, INPUT, NONE);
- PIN_SLP(gpy2-4, INPUT, NONE);
- PIN_SLP(gpy2-5, INPUT, NONE);
-
- PIN_SLP(gpy3-0, INPUT, DOWN);
- PIN_SLP(gpy3-1, INPUT, DOWN);
- PIN_SLP(gpy3-2, INPUT, DOWN);
- PIN_SLP(gpy3-3, INPUT, DOWN);
- PIN_SLP(gpy3-4, INPUT, DOWN);
- PIN_SLP(gpy3-5, INPUT, DOWN);
- PIN_SLP(gpy3-6, INPUT, DOWN);
- PIN_SLP(gpy3-7, INPUT, DOWN);
-
- PIN_SLP(gpy4-0, INPUT, DOWN);
- PIN_SLP(gpy4-1, INPUT, DOWN);
- PIN_SLP(gpy4-2, INPUT, DOWN);
- PIN_SLP(gpy4-3, INPUT, DOWN);
- PIN_SLP(gpy4-4, INPUT, DOWN);
- PIN_SLP(gpy4-5, INPUT, DOWN);
- PIN_SLP(gpy4-6, INPUT, DOWN);
- PIN_SLP(gpy4-7, INPUT, DOWN);
-
- PIN_SLP(gpy5-0, INPUT, DOWN);
- PIN_SLP(gpy5-1, INPUT, DOWN);
- PIN_SLP(gpy5-2, INPUT, DOWN);
- PIN_SLP(gpy5-3, INPUT, DOWN);
- PIN_SLP(gpy5-4, INPUT, DOWN);
- PIN_SLP(gpy5-5, INPUT, DOWN);
- PIN_SLP(gpy5-6, INPUT, DOWN);
- PIN_SLP(gpy5-7, INPUT, DOWN);
-
- PIN_SLP(gpy6-0, INPUT, DOWN);
- PIN_SLP(gpy6-1, INPUT, DOWN);
- PIN_SLP(gpy6-2, INPUT, DOWN);
- PIN_SLP(gpy6-3, INPUT, DOWN);
- PIN_SLP(gpy6-4, INPUT, DOWN);
- PIN_SLP(gpy6-5, INPUT, DOWN);
- PIN_SLP(gpy6-6, INPUT, DOWN);
- PIN_SLP(gpy6-7, INPUT, DOWN);
- };
-};
-
-&pinctrl_2 {
- pinctrl-names = "default";
- pinctrl-0 = <&sleep2>;
-
- sleep2: sleep-states {
- PIN_SLP(gpz-0, INPUT, DOWN);
- PIN_SLP(gpz-1, INPUT, DOWN);
- PIN_SLP(gpz-2, INPUT, DOWN);
- PIN_SLP(gpz-3, INPUT, DOWN);
- PIN_SLP(gpz-4, INPUT, DOWN);
- PIN_SLP(gpz-5, INPUT, DOWN);
- PIN_SLP(gpz-6, INPUT, DOWN);
- };
-};
-
-&pinctrl_3 {
- pinctrl-names = "default";
- pinctrl-0 = <&sleep3>;
-
- sleep3: sleep-states {
- PIN_SLP(gpv0-0, INPUT, DOWN);
- PIN_SLP(gpv0-1, INPUT, DOWN);
- PIN_SLP(gpv0-2, INPUT, DOWN);
- PIN_SLP(gpv0-3, INPUT, DOWN);
- PIN_SLP(gpv0-4, INPUT, DOWN);
- PIN_SLP(gpv0-5, INPUT, DOWN);
- PIN_SLP(gpv0-6, INPUT, DOWN);
- PIN_SLP(gpv0-7, INPUT, DOWN);
-
- PIN_SLP(gpv1-0, INPUT, DOWN);
- PIN_SLP(gpv1-1, INPUT, DOWN);
- PIN_SLP(gpv1-2, INPUT, DOWN);
- PIN_SLP(gpv1-3, INPUT, DOWN);
- PIN_SLP(gpv1-4, INPUT, DOWN);
- PIN_SLP(gpv1-5, INPUT, DOWN);
- PIN_SLP(gpv1-6, INPUT, DOWN);
- PIN_SLP(gpv1-7, INPUT, DOWN);
-
- PIN_SLP(gpv2-0, INPUT, DOWN);
- PIN_SLP(gpv2-1, INPUT, DOWN);
- PIN_SLP(gpv2-2, INPUT, DOWN);
- PIN_SLP(gpv2-3, INPUT, DOWN);
- PIN_SLP(gpv2-4, INPUT, DOWN);
- PIN_SLP(gpv2-5, INPUT, DOWN);
- PIN_SLP(gpv2-6, INPUT, DOWN);
- PIN_SLP(gpv2-7, INPUT, DOWN);
-
- PIN_SLP(gpv3-0, INPUT, DOWN);
- PIN_SLP(gpv3-1, INPUT, DOWN);
- PIN_SLP(gpv3-2, INPUT, DOWN);
- PIN_SLP(gpv3-3, INPUT, DOWN);
- PIN_SLP(gpv3-4, INPUT, DOWN);
- PIN_SLP(gpv3-5, INPUT, DOWN);
- PIN_SLP(gpv3-6, INPUT, DOWN);
- PIN_SLP(gpv3-7, INPUT, DOWN);
-
- PIN_SLP(gpv4-0, INPUT, DOWN);
- };
-};
-
-&pwm {
- pinctrl-0 = <&pwm0_out>;
- pinctrl-names = "default";
- samsung,pwm-outputs = <0>;
- status = "okay";
-};
-
-&rtc {
- status = "okay";
- clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
- clock-names = "rtc", "rtc_src";
-};
-
-&sdhci_2 {
- bus-width = <4>;
- cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
- cd-inverted;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo21_reg>;
- status = "okay";
-};
-
-&sdhci_3 {
- #address-cells = <1>;
- #size-cells = <0>;
- non-removable;
- bus-width = <4>;
-
- mmc-pwrseq = <&wlan_pwrseq>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
- status = "okay";
-
- brcmf: wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- interrupt-parent = <&gpx2>;
- interrupts = <5 IRQ_TYPE_NONE>;
- interrupt-names = "host-wake";
- };
-};
-
-&serial_0 {
- status = "okay";
-};
-
-&serial_1 {
- status = "okay";
-};
-
-&serial_2 {
- status = "okay";
-};
-
-&serial_3 {
- status = "okay";
-};
-
-&spi_1 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_bus>;
- cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
- status = "okay";
-
- s5c73m3_spi: s5c73m3@0 {
- compatible = "samsung,s5c73m3";
- spi-max-frequency = <50000000>;
- reg = <0>;
- controller-data {
- samsung,spi-feedback-delay = <2>;
- };
- };
-};
-
-&tmu {
- vtmu-supply = <&ldo10_reg>;
- status = "okay";
-};
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4412 based Trats 2 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ */
+
+/dts-v1/;
+#include "exynos4412-galaxy-s3.dtsi"
+
+/ {
+ model = "Samsung Trats 2 based on Exynos4412";
+ compatible = "samsung,trats2", "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x40000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttySAC2,115200N8 root=/dev/mmcblk0p5 rootwait earlyprintk panic=5";
+ };
+
+};
The midas boards share a lot with trats2. Split the common parts out of trats2 into a common midas dtsi and a common "galaxy s3" dts. Signed-off-by: Simon Shields <simon@lineageos.org> --- arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi | 140 ++ ...exynos4412-trats2.dts => exynos4412-midas.dtsi} | 119 +- arch/arm/boot/dts/exynos4412-trats2.dts | 1441 +------------------- 3 files changed, 173 insertions(+), 1527 deletions(-) create mode 100644 arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi copy arch/arm/boot/dts/{exynos4412-trats2.dts => exynos4412-midas.dtsi} (91%) rewrite arch/arm/boot/dts/exynos4412-trats2.dts (98%)