| Message ID | 20230214104508.51955-6-krzysztof.kozlowski@linaro.org (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | media: dt-bindings: Convert Samsung SoC Camera to DT schema | expand |
On Tue, Feb 14, 2023 at 11:45:06AM +0100, Krzysztof Kozlowski wrote: > Convert the Samsung Exynos4212/4412 SoC Imaging Subsystem (FIMC-IS) > bindings to DT schema. Changes during conversion - adjust to existing > DTS and Linux driver: add iommus and power-domains. > > Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > --- > .../bindings/media/exynos4-fimc-is.txt | 50 ---- > .../media/samsung,exynos4212-fimc-is.yaml | 221 ++++++++++++++++++ > MAINTAINERS | 1 + > 3 files changed, 222 insertions(+), 50 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/media/exynos4-fimc-is.txt > create mode 100644 Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml > > diff --git a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt > deleted file mode 100644 > index 32ced99d4244..000000000000 > --- a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt > +++ /dev/null > @@ -1,50 +0,0 @@ > -Exynos4x12 SoC series Imaging Subsystem (FIMC-IS) > - > -The FIMC-IS is a subsystem for processing image signal from an image sensor. > -The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5 > -processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C > -and SPI bus controllers, PWM and ADC. > - > -fimc-is node > ------------- > - > -Required properties: > -- compatible : should be "samsung,exynos4212-fimc-is" for Exynos4212 and > - Exynos4412 SoCs; > -- reg : physical base address and length of the registers set; > -- interrupts : must contain two FIMC-IS interrupts, in order: ISP0, ISP1; > -- clocks : list of clock specifiers, corresponding to entries in > - clock-names property; > -- clock-names : must contain "ppmuispx", "ppmuispx", "lite0", "lite1" > - "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "gicisp", > - "pwm_isp", "mcuctl_isp", "uart", "ispdiv0", "ispdiv1", > - "mcuispdiv0", "mcuispdiv1", "aclk200", "div_aclk200", > - "aclk400mcuisp", "div_aclk400mcuisp" entries, > - matching entries in the clocks property. > -pmu subnode > ------------ > - > -Required properties: > - - reg : must contain PMU physical base address and size of the register set. > - > -The following are the FIMC-IS peripheral device nodes and can be specified > -either standalone or as the fimc-is node child nodes. > - > -i2c-isp (ISP I2C bus controller) nodes > ------------------------------------------- > - > -Required properties: > - > -- compatible : should be "samsung,exynos4212-i2c-isp" for Exynos4212 and > - Exynos4412 SoCs; > -- reg : physical base address and length of the registers set; > -- clocks : must contain gate clock specifier for this controller; > -- clock-names : must contain "i2c_isp" entry. > - > -For the above nodes it is required to specify a pinctrl state named "default", > -according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt. > - > -Device tree nodes of the image sensors' controlled directly by the FIMC-IS > -firmware must be child nodes of their corresponding ISP I2C bus controller node. > -The data link of these image sensors must be specified using the common video > -interfaces bindings, defined in video-interfaces.txt. > diff --git a/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml > new file mode 100644 > index 000000000000..288f4bf3d44d > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml > @@ -0,0 +1,221 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/samsung,exynos4212-fimc-is.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Samsung Exynos4212/4412 SoC Imaging Subsystem (FIMC-IS) > + > +maintainers: > + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > + - Sylwester Nawrocki <s.nawrocki@samsung.com> > + > +description: > + The FIMC-IS is a subsystem for processing image signal from an image sensor. > + The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5 > + processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C > + and SPI bus controllers, PWM and ADC. > + > +properties: > + compatible: > + enum: > + - samsung,exynos4212-fimc-is > + > + reg: > + maxItems: 1 > + > + '#address-cells': > + const: 1 > + > + clocks: > + maxItems: 21 > + > + clock-names: > + items: > + - const: lite0 > + - const: lite1 > + - const: ppmuispx > + - const: ppmuispmx > + - const: isp > + - const: drc > + - const: fd > + - const: mcuisp > + - const: gicisp > + - const: mcuctl_isp > + - const: pwm_isp > + - const: ispdiv0 > + - const: ispdiv1 > + - const: mcuispdiv0 > + - const: mcuispdiv1 > + - const: mpll > + - const: aclk200 > + - const: aclk400mcuisp > + - const: div_aclk200 > + - const: div_aclk400mcuisp > + - const: uart > + > + interrupts: > + maxItems: 2 > + > + iommus: > + maxItems: 4 > + > + iommu-names: > + items: > + - const: isp > + - const: drc > + - const: fd > + - const: mcuctl > + > + power-domains: > + maxItems: 1 > + > + ranges: true > + > + '#size-cells': > + const: 1 Normally this is next to #address-cells. > + > +patternProperties: > + "^pmu@[0-9a-f]+$": > + type: object > + additionalProperties: false > + description: > + Node representing the SoC's Power Management Unit (duplicated with the > + correct PMU node in the SoC). > + > + properties: > + reg: > + maxItems: 1 > + > + required: > + - reg > + > + "^i2c-isp@[0-9a-f]+$": > + type: object > + $ref: /schemas/i2c/i2c-controller.yaml# > + unevaluatedProperties: false > + #additionalProperties: false ?? > + description: > + ISP I2C bus controller
On 15/02/2023 21:53, Rob Herring wrote: >> + power-domains: >> + maxItems: 1 >> + >> + ranges: true >> + >> + '#size-cells': >> + const: 1 > > Normally this is next to #address-cells. I kept alphabetical sorting, but I can move this with ranges close to the reg/address-cells. > >> + >> +patternProperties: >> + "^pmu@[0-9a-f]+$": >> + type: object >> + additionalProperties: false >> + description: >> + Node representing the SoC's Power Management Unit (duplicated with the >> + correct PMU node in the SoC). >> + >> + properties: >> + reg: >> + maxItems: 1 >> + >> + required: >> + - reg >> + >> + "^i2c-isp@[0-9a-f]+$": >> + type: object >> + $ref: /schemas/i2c/i2c-controller.yaml# >> + unevaluatedProperties: false >> + #additionalProperties: false > > ?? Indeed, some debug code... Best regards, Krzysztof
diff --git a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt deleted file mode 100644 index 32ced99d4244..000000000000 --- a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt +++ /dev/null @@ -1,50 +0,0 @@ -Exynos4x12 SoC series Imaging Subsystem (FIMC-IS) - -The FIMC-IS is a subsystem for processing image signal from an image sensor. -The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5 -processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C -and SPI bus controllers, PWM and ADC. - -fimc-is node ------------- - -Required properties: -- compatible : should be "samsung,exynos4212-fimc-is" for Exynos4212 and - Exynos4412 SoCs; -- reg : physical base address and length of the registers set; -- interrupts : must contain two FIMC-IS interrupts, in order: ISP0, ISP1; -- clocks : list of clock specifiers, corresponding to entries in - clock-names property; -- clock-names : must contain "ppmuispx", "ppmuispx", "lite0", "lite1" - "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "gicisp", - "pwm_isp", "mcuctl_isp", "uart", "ispdiv0", "ispdiv1", - "mcuispdiv0", "mcuispdiv1", "aclk200", "div_aclk200", - "aclk400mcuisp", "div_aclk400mcuisp" entries, - matching entries in the clocks property. -pmu subnode ------------ - -Required properties: - - reg : must contain PMU physical base address and size of the register set. - -The following are the FIMC-IS peripheral device nodes and can be specified -either standalone or as the fimc-is node child nodes. - -i2c-isp (ISP I2C bus controller) nodes ------------------------------------------- - -Required properties: - -- compatible : should be "samsung,exynos4212-i2c-isp" for Exynos4212 and - Exynos4412 SoCs; -- reg : physical base address and length of the registers set; -- clocks : must contain gate clock specifier for this controller; -- clock-names : must contain "i2c_isp" entry. - -For the above nodes it is required to specify a pinctrl state named "default", -according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt. - -Device tree nodes of the image sensors' controlled directly by the FIMC-IS -firmware must be child nodes of their corresponding ISP I2C bus controller node. -The data link of these image sensors must be specified using the common video -interfaces bindings, defined in video-interfaces.txt. diff --git a/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml new file mode 100644 index 000000000000..288f4bf3d44d --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml @@ -0,0 +1,221 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,exynos4212-fimc-is.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos4212/4412 SoC Imaging Subsystem (FIMC-IS) + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: + The FIMC-IS is a subsystem for processing image signal from an image sensor. + The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5 + processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C + and SPI bus controllers, PWM and ADC. + +properties: + compatible: + enum: + - samsung,exynos4212-fimc-is + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + clocks: + maxItems: 21 + + clock-names: + items: + - const: lite0 + - const: lite1 + - const: ppmuispx + - const: ppmuispmx + - const: isp + - const: drc + - const: fd + - const: mcuisp + - const: gicisp + - const: mcuctl_isp + - const: pwm_isp + - const: ispdiv0 + - const: ispdiv1 + - const: mcuispdiv0 + - const: mcuispdiv1 + - const: mpll + - const: aclk200 + - const: aclk400mcuisp + - const: div_aclk200 + - const: div_aclk400mcuisp + - const: uart + + interrupts: + maxItems: 2 + + iommus: + maxItems: 4 + + iommu-names: + items: + - const: isp + - const: drc + - const: fd + - const: mcuctl + + power-domains: + maxItems: 1 + + ranges: true + + '#size-cells': + const: 1 + +patternProperties: + "^pmu@[0-9a-f]+$": + type: object + additionalProperties: false + description: + Node representing the SoC's Power Management Unit (duplicated with the + correct PMU node in the SoC). + + properties: + reg: + maxItems: 1 + + required: + - reg + + "^i2c-isp@[0-9a-f]+$": + type: object + $ref: /schemas/i2c/i2c-controller.yaml# + unevaluatedProperties: false + #additionalProperties: false + description: + ISP I2C bus controller + + properties: + compatible: + const: samsung,exynos4212-i2c-isp + + reg: + maxItems: 1 + + + clocks: + maxItems: 1 + + clock-names: + items: + - const: i2c_isp + + pinctrl-0: true + pinctrl-names: + items: + - const: default + + required: + - compatible + - reg + - clocks + - clock-names + +required: + - compatible + - reg + - '#address-cells' + - clocks + - clock-names + - interrupts + - ranges + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + fimc-is@12000000 { + compatible = "samsung,exynos4212-fimc-is"; + reg = <0x12000000 0x260000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&isp_clock CLK_ISP_FIMC_LITE0>, + <&isp_clock CLK_ISP_FIMC_LITE1>, + <&isp_clock CLK_ISP_PPMUISPX>, + <&isp_clock CLK_ISP_PPMUISPMX>, + <&isp_clock CLK_ISP_FIMC_ISP>, + <&isp_clock CLK_ISP_FIMC_DRC>, + <&isp_clock CLK_ISP_FIMC_FD>, + <&isp_clock CLK_ISP_MCUISP>, + <&isp_clock CLK_ISP_GICISP>, + <&isp_clock CLK_ISP_MCUCTL_ISP>, + <&isp_clock CLK_ISP_PWM_ISP>, + <&isp_clock CLK_ISP_DIV_ISP0>, + <&isp_clock CLK_ISP_DIV_ISP1>, + <&isp_clock CLK_ISP_DIV_MCUISP0>, + <&isp_clock CLK_ISP_DIV_MCUISP1>, + <&clock CLK_MOUT_MPLL_USER_T>, + <&clock CLK_ACLK200>, + <&clock CLK_ACLK400_MCUISP>, + <&clock CLK_DIV_ACLK200>, + <&clock CLK_DIV_ACLK400_MCUISP>, + <&clock CLK_UART_ISP_SCLK>; + clock-names = "lite0", "lite1", "ppmuispx", + "ppmuispmx", "isp", + "drc", "fd", "mcuisp", + "gicisp", "mcuctl_isp", "pwm_isp", + "ispdiv0", "ispdiv1", "mcuispdiv0", + "mcuispdiv1", "mpll", "aclk200", + "aclk400mcuisp", "div_aclk200", + "div_aclk400mcuisp", "uart"; + iommus = <&sysmmu_fimc_isp>, <&sysmmu_fimc_drc>, + <&sysmmu_fimc_fd>, <&sysmmu_fimc_mcuctl>; + iommu-names = "isp", "drc", "fd", "mcuctl"; + power-domains = <&pd_isp>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pmu@10020000 { + reg = <0x10020000 0x3000>; + }; + + i2c-isp@12140000 { + compatible = "samsung,exynos4212-i2c-isp"; + reg = <0x12140000 0x100>; + clocks = <&isp_clock CLK_ISP_I2C1_ISP>; + clock-names = "i2c_isp"; + pinctrl-0 = <&fimc_is_i2c1>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + image-sensor@10 { + compatible = "samsung,s5k6a3"; + reg = <0x10>; + svdda-supply = <&cam_io_reg>; + svddio-supply = <&ldo19_reg>; + afvdd-supply = <&ldo19_reg>; + clock-frequency = <24000000>; + clocks = <&camera 1>; + clock-names = "extclk"; + gpios = <&gpm1 6 GPIO_ACTIVE_LOW>; + + port { + endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 2789c436c875..0f22dc1c95ae 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -18466,6 +18466,7 @@ L: linux-media@vger.kernel.org S: Supported Q: https://patchwork.linuxtv.org/project/linux-media/list/ F: Documentation/devicetree/bindings/media/samsung,exynos4210-csis.yaml +F: Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml F: Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-lite.yaml F: drivers/media/platform/samsung/exynos4-is/
Convert the Samsung Exynos4212/4412 SoC Imaging Subsystem (FIMC-IS) bindings to DT schema. Changes during conversion - adjust to existing DTS and Linux driver: add iommus and power-domains. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- .../bindings/media/exynos4-fimc-is.txt | 50 ---- .../media/samsung,exynos4212-fimc-is.yaml | 221 ++++++++++++++++++ MAINTAINERS | 1 + 3 files changed, 222 insertions(+), 50 deletions(-) delete mode 100644 Documentation/devicetree/bindings/media/exynos4-fimc-is.txt create mode 100644 Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml