| Message ID | 20230819031731.22618-8-semen.protsenko@linaro.org (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: exynos: Enable USB for E850-96 board | expand |
On 19/08/2023 05:17, Sam Protsenko wrote: > Add USB controller and USB PHY controller nodes for Exynos850 SoC. > > The USB controller has next features: > - Dual Role Device (DRD) controller > - DWC3 compatible > - Supports USB 2.0 host and USB 2.0 device interfaces > - Supports full-speed (12 Mbps) and high-speed (480 Mbps) modes with > USB device 2.0 interface > - Supports on-chip USB PHY transceiver > - Supports up to 16 bi-directional endpoints (that includes control > endpoint 0) > - Complies with xHCI 1.00 specification > > Only USB 2.0 is supported in Exynos850, so only UTMI+ PHY interface is > specified in "phys" property (index 0) and PIPE3 is omitted (index 1). > > Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> > --- > arch/arm64/boot/dts/exynos/exynos850.dtsi | 30 +++++++++++++++++++++++ > 1 file changed, 30 insertions(+) > > diff --git a/arch/arm64/boot/dts/exynos/exynos850.dtsi b/arch/arm64/boot/dts/exynos/exynos850.dtsi > index aa077008b3be..198d1dfcc672 100644 > --- a/arch/arm64/boot/dts/exynos/exynos850.dtsi > +++ b/arch/arm64/boot/dts/exynos/exynos850.dtsi > @@ -570,6 +570,36 @@ sysreg_cmgp: syscon@11c20000 { > clocks = <&cmu_cmgp CLK_GOUT_SYSREG_CMGP_PCLK>; > }; > > + usbdrd: usb@13600000 { > + compatible = "samsung,exynos850-dwusb3"; > + clocks = <&cmu_hsi CLK_GOUT_USB_BUS_EARLY_CLK>, > + <&cmu_hsi CLK_GOUT_USB_REF_CLK>; > + clock-names = "bus_early", "ref"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0x0 0x13600000 0x10000>; Please put ranges after compatible. I know that existing code does not follow this convention, though. > + status = "disabled"; > + Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/exynos/exynos850.dtsi b/arch/arm64/boot/dts/exynos/exynos850.dtsi index aa077008b3be..198d1dfcc672 100644 --- a/arch/arm64/boot/dts/exynos/exynos850.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos850.dtsi @@ -570,6 +570,36 @@ sysreg_cmgp: syscon@11c20000 { clocks = <&cmu_cmgp CLK_GOUT_SYSREG_CMGP_PCLK>; }; + usbdrd: usb@13600000 { + compatible = "samsung,exynos850-dwusb3"; + clocks = <&cmu_hsi CLK_GOUT_USB_BUS_EARLY_CLK>, + <&cmu_hsi CLK_GOUT_USB_REF_CLK>; + clock-names = "bus_early", "ref"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x13600000 0x10000>; + status = "disabled"; + + usbdrd_dwc3: usb@0 { + compatible = "snps,dwc3"; + reg = <0x0 0x10000>; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd_phy 0>; + phy-names = "usb2-phy"; + }; + }; + + usbdrd_phy: phy@135d0000 { + compatible = "samsung,exynos850-usbdrd-phy"; + reg = <0x135d0000 0x100>; + clocks = <&cmu_hsi CLK_GOUT_USB_PHY_ACLK>, + <&cmu_hsi CLK_GOUT_USB_PHY_REF_CLK>; + clock-names = "phy", "ref"; + samsung,pmu-syscon = <&pmu_system_controller>; + #phy-cells = <1>; + status = "disabled"; + }; + usi_uart: usi@138200c0 { compatible = "samsung,exynos850-usi"; reg = <0x138200c0 0x20>;
Add USB controller and USB PHY controller nodes for Exynos850 SoC. The USB controller has next features: - Dual Role Device (DRD) controller - DWC3 compatible - Supports USB 2.0 host and USB 2.0 device interfaces - Supports full-speed (12 Mbps) and high-speed (480 Mbps) modes with USB device 2.0 interface - Supports on-chip USB PHY transceiver - Supports up to 16 bi-directional endpoints (that includes control endpoint 0) - Complies with xHCI 1.00 specification Only USB 2.0 is supported in Exynos850, so only UTMI+ PHY interface is specified in "phys" property (index 0) and PIPE3 is omitted (index 1). Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> --- arch/arm64/boot/dts/exynos/exynos850.dtsi | 30 +++++++++++++++++++++++ 1 file changed, 30 insertions(+)