diff mbox

[v2,06/20,SCSI] mpt3sas: Provides the physical location of sas drives

Message ID 1435647306-36956-7-git-send-email-Sreekanth.Reddy@avagotech.com (mailing list archive)
State New, archived
Headers show

Commit Message

Sreekanth Reddy June 30, 2015, 6:54 a.m. UTC 
This Patch will provide more details of the devices such as slot number, enclosure logical id, enclosure level & connector name in the following scenarios,

- When end device is added in the topology,
- When the end device is removed from the setup,
- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during error handling,
- When any command to the device fails with Sense key Hardware error or Medium error or Unit Attention,
- When firmware returns device error or device not ready status for the end device,
- When a Predicted fault is detected on an end device.

This information can be used by the user to identify the location of the desired drive in the topology.

Driver will get these information by reading the sas device page0.

Changes in v2:
     Fixed the undefined scsih_scsi_ioc_info() function compilation errors which we observe 
only if CONFIG_SCSI_MPT3SAS_LOGGING flag is disabled.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.h  |   2 +
 drivers/scsi/mpt3sas/mpt3sas_scsih.c | 240 +++++++++++++++++++++++++++++------
 2 files changed, 203 insertions(+), 39 deletions(-)
diff mbox

Patch

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index 01d92db..da82a97 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -324,6 +324,8 @@  struct _sas_device {
 	u8	fast_path;
 	u8	pfa_led_on;
 	u8	pend_sas_rphy_add;
+	u8	enclosure_level;
+	u8	connector_name[4];
 };
 
 /**
diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index d457dba..ec3b3d3 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -585,6 +585,22 @@  _scsih_sas_device_remove(struct MPT3SAS_ADAPTER *ioc,
 
 	if (!sas_device)
 		return;
+	pr_info(MPT3SAS_FMT
+	    "removing handle(0x%04x), sas_addr(0x%016llx)\n",
+	    ioc->name, sas_device->handle,
+	    (unsigned long long) sas_device->sas_address);
+
+	if (sas_device->enclosure_handle != 0)
+		pr_info(MPT3SAS_FMT
+		   "removing enclosure logical id(0x%016llx), slot(%d)\n",
+		   ioc->name, (unsigned long long)
+		   sas_device->enclosure_logical_id, sas_device->slot);
+
+	if (sas_device->connector_name[0] != '\0')
+		pr_info(MPT3SAS_FMT
+		   "removing enclosure level(0x%04x), connector name( %s)\n",
+		   ioc->name, sas_device->enclosure_level,
+		   sas_device->connector_name);
 
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_del(&sas_device->list);
@@ -663,6 +679,18 @@  _scsih_sas_device_add(struct MPT3SAS_ADAPTER *ioc,
 		ioc->name, __func__, sas_device->handle,
 		(unsigned long long)sas_device->sas_address));
 
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure logical id(0x%016llx), slot( %d)\n",
+		    ioc->name, __func__, (unsigned long long)
+		    sas_device->enclosure_logical_id, sas_device->slot));
+
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure level(0x%04x), connector name( %s)\n",
+		    ioc->name, __func__,
+		    sas_device->enclosure_level, sas_device->connector_name));
+
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_add_tail(&sas_device->list, &ioc->sas_device_list);
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
@@ -704,6 +732,18 @@  _scsih_sas_device_init_add(struct MPT3SAS_ADAPTER *ioc,
 		__func__, sas_device->handle,
 		(unsigned long long)sas_device->sas_address));
 
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure logical id(0x%016llx), slot( %d)\n",
+		    ioc->name, __func__, (unsigned long long)
+		    sas_device->enclosure_logical_id, sas_device->slot));
+
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure level(0x%04x), connector name( %s)\n",
+		    ioc->name, __func__, sas_device->enclosure_level,
+		    sas_device->connector_name));
+
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_add_tail(&sas_device->list, &ioc->sas_device_init_list);
 	_scsih_determine_boot_device(ioc, sas_device, 0);
@@ -1772,10 +1812,16 @@  _scsih_slave_configure(struct scsi_device *sdev)
 	    "sas_addr(0x%016llx), phy(%d), device_name(0x%016llx)\n",
 	    ds, handle, (unsigned long long)sas_device->sas_address,
 	    sas_device->phy, (unsigned long long)sas_device->device_name);
-	sdev_printk(KERN_INFO, sdev,
-		"%s: enclosure_logical_id(0x%016llx), slot(%d)\n",
-		ds, (unsigned long long)
-	    sas_device->enclosure_logical_id, sas_device->slot);
+	if (sas_device->enclosure_handle != 0)
+		sdev_printk(KERN_INFO, sdev,
+		     "%s: enclosure_logical_id(0x%016llx), slot(%d)\n",
+		     ds, (unsigned long long)
+		     sas_device->enclosure_logical_id, sas_device->slot);
+	if (sas_device->connector_name[0] != '\0')
+		sdev_printk(KERN_INFO, sdev,
+		     "%s: enclosure level(0x%04x), connector name( %s)\n",
+		     ds, sas_device->enclosure_level,
+		     sas_device->connector_name);
 
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 
@@ -2189,10 +2235,17 @@  _scsih_tm_display_info(struct MPT3SAS_ADAPTER *ioc, struct scsi_cmnd *scmd)
 			    sas_device->handle,
 			    (unsigned long long)sas_device->sas_address,
 			    sas_device->phy);
-			starget_printk(KERN_INFO, starget,
-			    "enclosure_logical_id(0x%016llx), slot(%d)\n",
-			   (unsigned long long)sas_device->enclosure_logical_id,
-			    sas_device->slot);
+			if (sas_device->enclosure_handle != 0)
+				starget_printk(KERN_INFO, starget,
+				 "enclosure_logical_id(0x%016llx), slot(%d)\n",
+				 (unsigned long long)
+				 sas_device->enclosure_logical_id,
+				 sas_device->slot);
+			if (sas_device->connector_name)
+				starget_printk(KERN_INFO, starget,
+				"enclosure level(0x%04x),connector name(%s)\n",
+				 sas_device->enclosure_level,
+				 sas_device->connector_name);
 		}
 		spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 	}
@@ -2813,6 +2866,18 @@  _scsih_tm_tr_send(struct MPT3SAS_ADAPTER *ioc, u16 handle)
 			"setting delete flag: handle(0x%04x), sas_addr(0x%016llx)\n",
 			ioc->name, handle,
 		    (unsigned long long)sas_address));
+		if (sas_device->enclosure_handle != 0)
+			dewtprintk(ioc, pr_info(MPT3SAS_FMT
+			 "setting delete flag:enclosure logical id(0x%016llx),"
+			 " slot(%d)\n", ioc->name, (unsigned long long)
+			  sas_device->enclosure_logical_id,
+			  sas_device->slot));
+		if (sas_device->connector_name)
+			dewtprintk(ioc, pr_info(MPT3SAS_FMT
+			 "setting delete flag: enclosure level(0x%04x),"
+			 " connector name( %s)\n", ioc->name,
+			  sas_device->enclosure_level,
+			  sas_device->connector_name));
 		_scsih_ublock_io_device(ioc, sas_address);
 		sas_target_priv_data->handle = MPT3SAS_INVALID_DEVICE_HANDLE;
 	}
@@ -3828,10 +3893,19 @@  _scsih_scsi_ioc_info(struct MPT3SAS_ADAPTER *ioc, struct scsi_cmnd *scmd,
 				"\tsas_address(0x%016llx), phy(%d)\n",
 				ioc->name, (unsigned long long)
 			    sas_device->sas_address, sas_device->phy);
-			pr_warn(MPT3SAS_FMT
-			    "\tenclosure_logical_id(0x%016llx), slot(%d)\n",
-			    ioc->name, (unsigned long long)
-			    sas_device->enclosure_logical_id, sas_device->slot);
+			if (sas_device->enclosure_handle != 0)
+				pr_warn(MPT3SAS_FMT
+				  "\tenclosure_logical_id(0x%016llx),"
+				  "slot(%d)\n", ioc->name,
+				  (unsigned long long)
+				  sas_device->enclosure_logical_id,
+				  sas_device->slot);
+			if (sas_device->connector_name[0])
+				pr_warn(MPT3SAS_FMT
+				  "\tenclosure level(0x%04x),"
+				  " connector name( %s)\n", ioc->name,
+				  sas_device->enclosure_level,
+				  sas_device->connector_name);
 		}
 		spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 	}
@@ -4006,7 +4080,16 @@  _scsih_smart_predicted_fault(struct MPT3SAS_ADAPTER *ioc, u16 handle)
 		spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 		return;
 	}
-	starget_printk(KERN_WARNING, starget, "predicted fault\n");
+	if (sas_device->enclosure_handle != 0)
+		starget_printk(KERN_INFO, starget, "predicted fault, "
+			"enclosure logical id(0x%016llx), slot(%d)\n",
+			(unsigned long long)sas_device->enclosure_logical_id,
+			sas_device->slot);
+	if (sas_device->connector_name[0] != '\0')
+		starget_printk(KERN_WARNING, starget, "predicted fault, "
+			"enclosure level(0x%04x), connector name( %s)\n",
+			sas_device->enclosure_level,
+			sas_device->connector_name);
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 
 	if (ioc->pdev->subsystem_vendor == PCI_VENDOR_ID_IBM)
@@ -4126,8 +4209,15 @@  _scsih_io_done(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 msix_index, u32 reply)
 			_scsih_smart_predicted_fault(ioc,
 			    le16_to_cpu(mpi_reply->DevHandle));
 		mpt3sas_trigger_scsi(ioc, data.skey, data.asc, data.ascq);
-	}
 
+#ifdef CONFIG_SCSI_MPT3SAS_LOGGING
+		if (!(ioc->logging_level & MPT_DEBUG_REPLY) &&
+		     ((scmd->sense_buffer[2] == UNIT_ATTENTION) ||
+		     (scmd->sense_buffer[2] == MEDIUM_ERROR) ||
+		     (scmd->sense_buffer[2] == HARDWARE_ERROR)))
+			_scsih_scsi_ioc_info(ioc, scmd, mpi_reply, smid);
+#endif
+	}
 	switch (ioc_status) {
 	case MPI2_IOCSTATUS_BUSY:
 	case MPI2_IOCSTATUS_INSUFFICIENT_RESOURCES:
@@ -4795,6 +4885,16 @@  _scsih_check_device(struct MPT3SAS_ADAPTER *ioc,
 			sas_device->handle, handle);
 		sas_target_priv_data->handle = handle;
 		sas_device->handle = handle;
+		if (sas_device_pg0.Flags &
+		     MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID) {
+			sas_device->enclosure_level =
+				le16_to_cpu(sas_device_pg0.EnclosureLevel);
+			memcpy(&sas_device->connector_name[0],
+				&sas_device_pg0.ConnectorName[0], 4);
+		} else {
+			sas_device->enclosure_level = 0;
+			sas_device->connector_name[0] = '\0';
+		}
 	}
 
 	/* check if device is present */
@@ -4901,14 +5001,24 @@  _scsih_add_device(struct MPT3SAS_ADAPTER *ioc, u16 handle, u8 phy_num,
 		    ioc->name, __FILE__, __LINE__, __func__);
 	sas_device->enclosure_handle =
 	    le16_to_cpu(sas_device_pg0.EnclosureHandle);
-	sas_device->slot =
-	    le16_to_cpu(sas_device_pg0.Slot);
+	if (sas_device->enclosure_handle != 0)
+		sas_device->slot =
+		    le16_to_cpu(sas_device_pg0.Slot);
 	sas_device->device_info = device_info;
 	sas_device->sas_address = sas_address;
 	sas_device->phy = sas_device_pg0.PhyNum;
 	sas_device->fast_path = (le16_to_cpu(sas_device_pg0.Flags) &
 	    MPI25_SAS_DEVICE0_FLAGS_FAST_PATH_CAPABLE) ? 1 : 0;
 
+	if (sas_device_pg0.Flags & MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID) {
+		sas_device->enclosure_level =
+			le16_to_cpu(sas_device_pg0.EnclosureLevel);
+		memcpy(&sas_device->connector_name[0],
+			&sas_device_pg0.ConnectorName[0], 4);
+	} else {
+		sas_device->enclosure_level = 0;
+		sas_device->connector_name[0] = '\0';
+	}
 	/* get enclosure_logical_id */
 	if (sas_device->enclosure_handle && !(mpt3sas_config_get_enclosure_pg0(
 	   ioc, &mpi_reply, &enclosure_pg0, MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE,
@@ -4950,6 +5060,18 @@  _scsih_remove_device(struct MPT3SAS_ADAPTER *ioc,
 		ioc->name, __func__,
 	    sas_device->handle, (unsigned long long)
 	    sas_device->sas_address));
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enter: enclosure logical id(0x%016llx), slot(%d)\n",
+		    ioc->name, __func__,
+		    (unsigned long long)sas_device->enclosure_logical_id,
+		    sas_device->slot));
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		  "%s: enter: enclosure level(0x%04x), connector name( %s)\n",
+		  ioc->name, __func__,
+		  sas_device->enclosure_level,
+		  sas_device->connector_name));
 
 	if (sas_device->starget && sas_device->starget->hostdata) {
 		sas_target_priv_data = sas_device->starget->hostdata;
@@ -4966,12 +5088,34 @@  _scsih_remove_device(struct MPT3SAS_ADAPTER *ioc,
 		"removing handle(0x%04x), sas_addr(0x%016llx)\n",
 		ioc->name, sas_device->handle,
 	    (unsigned long long) sas_device->sas_address);
+	if (sas_device->enclosure_handle != 0)
+		pr_info(MPT3SAS_FMT
+		  "removing : enclosure logical id(0x%016llx), slot(%d)\n",
+		  ioc->name,
+		  (unsigned long long)sas_device->enclosure_logical_id,
+		  sas_device->slot);
+	if (sas_device->connector_name[0] != '\0')
+		pr_info(MPT3SAS_FMT
+		  "removing enclosure level(0x%04x), connector name( %s)\n",
+		  ioc->name, sas_device->enclosure_level,
+		  sas_device->connector_name);
 
 	dewtprintk(ioc, pr_info(MPT3SAS_FMT
 		"%s: exit: handle(0x%04x), sas_addr(0x%016llx)\n",
 		ioc->name, __func__,
-	    sas_device->handle, (unsigned long long)
-	    sas_device->sas_address));
+		sas_device->handle, (unsigned long long)
+		sas_device->sas_address));
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: exit: enclosure logical id(0x%016llx), slot(%d)\n",
+		    ioc->name, __func__,
+		    (unsigned long long)sas_device->enclosure_logical_id,
+		    sas_device->slot));
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: exit: enclosure level(0x%04x), connector name(%s)\n",
+		    ioc->name, __func__, sas_device->enclosure_level,
+		    sas_device->connector_name));
 
 	kfree(sas_device);
 }
@@ -6364,9 +6508,7 @@  _scsih_prep_device_scan(struct MPT3SAS_ADAPTER *ioc)
 /**
  * _scsih_mark_responding_sas_device - mark a sas_devices as responding
  * @ioc: per adapter object
- * @sas_address: sas address
- * @slot: enclosure slot id
- * @handle: device handle
+ * @sas_device_pg0: SAS Device page 0
  *
  * After host reset, find out whether devices are still responding.
  * Used in _scsih_remove_unresponsive_sas_devices.
@@ -6374,8 +6516,8 @@  _scsih_prep_device_scan(struct MPT3SAS_ADAPTER *ioc)
  * Return nothing.
  */
 static void
-_scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc, u64 sas_address,
-	u16 slot, u16 handle)
+_scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc,
+Mpi2SasDevicePage0_t *sas_device_pg0)
 {
 	struct MPT3SAS_TARGET *sas_target_priv_data = NULL;
 	struct scsi_target *starget;
@@ -6384,8 +6526,8 @@  _scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc, u64 sas_address,
 
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_for_each_entry(sas_device, &ioc->sas_device_list, list) {
-		if (sas_device->sas_address == sas_address &&
-		    sas_device->slot == slot) {
+		if ((sas_device->sas_address == sas_device_pg0->SASAddress) &&
+			(sas_device->slot == sas_device_pg0->Slot)) {
 			sas_device->responding = 1;
 			starget = sas_device->starget;
 			if (starget && starget->hostdata) {
@@ -6394,22 +6536,40 @@  _scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc, u64 sas_address,
 				sas_target_priv_data->deleted = 0;
 			} else
 				sas_target_priv_data = NULL;
-			if (starget)
+			if (starget) {
 				starget_printk(KERN_INFO, starget,
-				    "handle(0x%04x), sas_addr(0x%016llx), "
-				    "enclosure logical id(0x%016llx), "
-				    "slot(%d)\n", handle,
-				    (unsigned long long)sas_device->sas_address,
+				    "handle(0x%04x), sas_addr(0x%016llx)\n",
+				    sas_device_pg0->DevHandle,
 				    (unsigned long long)
-				    sas_device->enclosure_logical_id,
-				    sas_device->slot);
-			if (sas_device->handle == handle)
+				    sas_device->sas_address);
+
+				if (sas_device->enclosure_handle != 0)
+					starget_printk(KERN_INFO, starget,
+					 "enclosure logical id(0x%016llx),"
+					 " slot(%d)\n",
+					 (unsigned long long)
+					 sas_device->enclosure_logical_id,
+					 sas_device->slot);
+			}
+			if (sas_device_pg0->Flags &
+			      MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID) {
+				sas_device->enclosure_level =
+				   le16_to_cpu(sas_device_pg0->EnclosureLevel);
+				memcpy(&sas_device->connector_name[0],
+					&sas_device_pg0->ConnectorName[0], 4);
+			} else {
+				sas_device->enclosure_level = 0;
+				sas_device->connector_name[0] = '\0';
+			}
+
+			if (sas_device->handle == sas_device_pg0->DevHandle)
 				goto out;
 			pr_info("\thandle changed from(0x%04x)!!!\n",
 			    sas_device->handle);
-			sas_device->handle = handle;
+			sas_device->handle = sas_device_pg0->DevHandle;
 			if (sas_target_priv_data)
-				sas_target_priv_data->handle = handle;
+				sas_target_priv_data->handle =
+					sas_device_pg0->DevHandle;
 			goto out;
 		}
 	}
@@ -6448,13 +6608,15 @@  _scsih_search_responding_sas_devices(struct MPT3SAS_ADAPTER *ioc)
 		    MPI2_IOCSTATUS_MASK;
 		if (ioc_status != MPI2_IOCSTATUS_SUCCESS)
 			break;
-		handle = le16_to_cpu(sas_device_pg0.DevHandle);
+		handle = sas_device_pg0.DevHandle =
+				le16_to_cpu(sas_device_pg0.DevHandle);
 		device_info = le32_to_cpu(sas_device_pg0.DeviceInfo);
 		if (!(_scsih_is_end_device(device_info)))
 			continue;
-		_scsih_mark_responding_sas_device(ioc,
-		    le64_to_cpu(sas_device_pg0.SASAddress),
-		    le16_to_cpu(sas_device_pg0.Slot), handle);
+		sas_device_pg0.SASAddress =
+				le64_to_cpu(sas_device_pg0.SASAddress);
+		sas_device_pg0.Slot = le16_to_cpu(sas_device_pg0.Slot);
+		_scsih_mark_responding_sas_device(ioc, &sas_device_pg0);
 	}
 
  out: