@@ -21,16 +21,6 @@ NCR53c400 card, the Trantor T130B in its default configuration:
The NCR53c400 does not support DMA but it does have Pseudo-DMA which is
supported by the driver.
-If the default configuration does not work for you, you can use the kernel
-command lines (eg using the lilo append command):
- ncr5380=addr,irq
- ncr53c400=addr,irq
- ncr53c400a=addr,irq
- dtc3181e=addr,irq
-
-The driver does not probe for any addresses or ports other than those in
-the OVERRIDE or given to the kernel as above.
-
This driver provides some information on what it has detected in
/proc/scsi/g_NCR5380/x where x is the scsi card number as detected at boot
time. More info to come in the future.
@@ -56,136 +56,6 @@ static struct override {
#define NO_OVERRIDES ARRAY_SIZE(overrides)
-#ifndef MODULE
-
-/**
- * internal_setup - handle lilo command string override
- * @board: BOARD_* identifier for the board
- * @str: unused
- * @ints: numeric parameters
- *
- * Do LILO command line initialization of the overrides array. Display
- * errors when needed
- *
- * Locks: none
- */
-
-static void __init internal_setup(int board, char *str, int *ints)
-{
- static int commandline_current;
- switch (board) {
- case BOARD_NCR5380:
- if (ints[0] != 2 && ints[0] != 3) {
- printk(KERN_ERR "generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n");
- return;
- }
- break;
- case BOARD_NCR53C400:
- if (ints[0] != 2) {
- printk(KERN_ERR "generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n");
- return;
- }
- break;
- case BOARD_NCR53C400A:
- if (ints[0] != 2) {
- printk(KERN_ERR "generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name) ",irq\n");
- return;
- }
- break;
- case BOARD_DTC3181E:
- if (ints[0] != 2) {
- printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name) ",irq\n");
- return;
- }
- break;
- }
-
- if (commandline_current < NO_OVERRIDES) {
- overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type) ints[1];
- overrides[commandline_current].irq = ints[2];
- if (ints[0] == 3)
- overrides[commandline_current].dma = ints[3];
- else
- overrides[commandline_current].dma = DMA_NONE;
- overrides[commandline_current].board = board;
- ++commandline_current;
- }
-}
-
-
-/**
- * do_NCR53C80_setup - set up entry point
- * @str: unused
- *
- * Setup function invoked at boot to parse the ncr5380= command
- * line.
- */
-
-static int __init do_NCR5380_setup(char *str)
-{
- int ints[10];
-
- get_options(str, ARRAY_SIZE(ints), ints);
- internal_setup(BOARD_NCR5380, str, ints);
- return 1;
-}
-
-/**
- * do_NCR53C400_setup - set up entry point
- * @str: unused
- * @ints: integer parameters from kernel setup code
- *
- * Setup function invoked at boot to parse the ncr53c400= command
- * line.
- */
-
-static int __init do_NCR53C400_setup(char *str)
-{
- int ints[10];
-
- get_options(str, ARRAY_SIZE(ints), ints);
- internal_setup(BOARD_NCR53C400, str, ints);
- return 1;
-}
-
-/**
- * do_NCR53C400A_setup - set up entry point
- * @str: unused
- * @ints: integer parameters from kernel setup code
- *
- * Setup function invoked at boot to parse the ncr53c400a= command
- * line.
- */
-
-static int __init do_NCR53C400A_setup(char *str)
-{
- int ints[10];
-
- get_options(str, ARRAY_SIZE(ints), ints);
- internal_setup(BOARD_NCR53C400A, str, ints);
- return 1;
-}
-
-/**
- * do_DTC3181E_setup - set up entry point
- * @str: unused
- * @ints: integer parameters from kernel setup code
- *
- * Setup function invoked at boot to parse the dtc3181e= command
- * line.
- */
-
-static int __init do_DTC3181E_setup(char *str)
-{
- int ints[10];
-
- get_options(str, ARRAY_SIZE(ints), ints);
- internal_setup(BOARD_DTC3181E, str, ints);
- return 1;
-}
-
-#endif
-
#ifndef SCSI_G_NCR5380_MEM
/*
* Configure I/O address of 53C400A or DTC436 by writing magic numbers
@@ -741,8 +611,3 @@ static struct isapnp_device_id id_table[] = {
MODULE_DEVICE_TABLE(isapnp, id_table);
#endif
-
-__setup("ncr5380=", do_NCR5380_setup);
-__setup("ncr53c400=", do_NCR53C400_setup);
-__setup("ncr53c400a=", do_NCR53C400A_setup);
-__setup("dtc3181e=", do_DTC3181E_setup);
Remove deprecated __setup for parsing command line parameters. g_NCR5380.* parameters could be used instead. This might break existing setups with g_NCR5380 built-in (if there are any). But it has to go in order to remove the overrides[] array. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> --- Documentation/scsi/g_NCR5380.txt | 10 --- drivers/scsi/g_NCR5380.c | 135 -------------------------------------- 2 files changed, 145 deletions(-)